|This article needs additional citations for verification. (April 2010)|
In computing and telecommunication, an escape character is a character which invokes an alternative interpretation on subsequent characters in a character sequence. An escape character is a particular case of metacharacters. Generally, the judgement of whether something is an escape character or not depends on context.
Escape characters are part of the syntax for many programming languages, data formats and communication protocols. For a given alphabet an escape character's purpose is to start character sequences (so named escape sequences) which have to be interpreted differently from the same characters occurring without the prefixed escape character. An escape character may not have its own meaning, so all escape sequences are of 2 or more characters.
There are usually two functions of escape sequences. The first is to encode a syntactic entity, such as device commands or special data which cannot be directly represented by the alphabet. The second use, referred to as character quoting, is to represent characters which cannot be typed in current context, or would have an undesired interpretation. In the latter case an escape sequence is a digraph consisting of an escape character itself and a "quoted" character.
Generally, an escape character is not a particular case of (device) control characters, nor vice versa. If we define control characters as non-graphic, or as having a special meaning for an output device (e.g. printer or text terminal) then any escape character for this device is a control one. But escape characters used in programming (see below) are graphic, hence are not control characters. Conversely most (but not all) of the ASCII "control characters" have some control function in isolation, therefore are not escape characters.
In many programming languages, an escape character also forms some escape sequences which are referred to control characters. For example, line break has an escape sequence of
- \' single quote
- \" double quote
- \\ backslash
- \n new line
- \r carriage return
- \t tab
- \b backspace
- \f form feed
- \v vertical tab (IE < 9 treats '\v' as 'v' instead of a vertical tab ('\x0B'). If cross-browser compatibility is a concern, use \x0B instead of \v.)
- \0 null character (U+0000 NULL) (only if the next character is not a decimal digit; else it’s an octal escape sequence)
Note that the \v and \0 escapes are not allowed in JSON strings.
ASCII escape character
The ASCII "escape" character (octal: \033, hexadecimal: \x1B, or ^[, or, in decimal, 27) is used in many output devices to start a series of characters called a control sequence or escape sequence. Typically, the escape character was sent first in such a sequence to alert the device that the following characters were to be interpreted as a control sequence rather than as plain characters, then one or more characters would follow to specify some detailed action, after which the device would go back to interpreting characters normally. For example, the sequence of ^[, followed by the printable characters
[2;10H, would cause a DEC VT102 terminal to move its cursor to the 10th cell of the 2nd line of the screen. This was later developed to ANSI escape codes covered by the ANSI X3.64 standard. The escape character also starts each command sequence in the Hewlett Packard Printer Command Language.
The Escape key is usually found on standard PC keyboards. However it is commonly absent from keyboards for PDAs and other devices not designed primarily for ASCII communications. The DEC VT220 series was one of the few popular keyboards that did not have a dedicated Esc key, instead using one of the keys above the main keypad. In user interfaces of 1970s–1980s it was not uncommon to use this key as an escape character, but in modern desktop computers such use is dropped. Sometimes the key was identified with AltMode (for alternative mode). Even with no dedicated key, the escape character code could be generated by typing '[' while simultaneously holding down the Control key, 'Ctrl'.
The Point-to-Point Protocol uses the 0x7D octet (\175, or ASCII: } ) as an escape character. The octet immediately following should be XORed by 0x20 before being passed to a higher level protocol. This is applied to both 0x7D itself and the control character 0x7E (which is used in PPP to mark the beginning and end of a frame) when those octets need to be transmitted by a higher level protocol encapsulated by PPP, as well as other octets negotiated when the link is established. That is, when a higher level protocol wishes to transmit 0x7D, it is transmitted as the sequence 0x7D 0x5D, and 0x7E is transmitted as 0x7D 0x5E.
In Bourne shell (sh), the asterisk (
*) and question mark (
?) characters are wildcard characters expanded via globbing. Without a preceding escape character, an
* will expand to the names of all files in the working directory that don't start with a period iff there are such files, otherwise
* remains unexpanded. So to refer to a file literally called "*", the shell must be told not to interpret it in this way, by preceding it with a backslash (
\). This modifies the interpretation of the asterisk (
rm * # delete all files in the current directory rm \* # delete the file named *
Windows Command Prompt
The Windows command-line interpreter uses a caret character (
^) to escape reserved characters that have special meanings (in particular:
& | ( ) < > ^). The DOS command-line interpreter, though it supports similar syntax, does not support this.
For example, on the Windows Command Prompt, this will result in a syntax error.
whereas this will output the string:
- Quoted-printable, which encodes 8-bit data into 7-bit data of limited line lengths, uses the equals sign "=" as an escape character.
- Leaning toothpick syndrome
- Stropping (syntax) – in some conventions a leading character (such as an apostrophe) functions as an escape character
Not to be confused with:
- Tim Hill (1998). "The Windows NT Command Shell". MacMillan Technical Publishing. Retrieved 2010-01-13.