The AMD CrossFireX™ Logo
AMD CrossFireX (previously known as CrossFire) is a brand name for the multi-GPU solution by Advanced Micro Devices, originally developed by ATI Technologies. The technology allows up to four GPUs to be used in a single computer to improve graphics performance.
CrossFire was first made available to the public on September 27, 2005. The system required a CrossFire-compliant motherboard with a pair of ATI Radeon PCI Express (PCIe) graphics cards. Radeon x800s, x850s, x1800s and x1900s came in a regular edition, and a 'CrossFire Edition' which has 'master' capability built into the hardware. 'Master' capability is a term used for 5 extra image compositing chips, which combine the output of both cards. One had to buy a Master card, and pair it with a regular card from the same series. The Master card shipped with a proprietary DVI Y-dongle, which plugged into the primary DVI ports on both cards, and into the monitor cable. This dongle serves as the main link between both cards, sending incomplete images between them, and complete images to the monitor. Low-end Radeon x1300 and x1600 cards have no 'CrossFire Edition' but are enabled via software, with communication forwarded via the standard PCI Express slots on the motherboard. ATI currently has not created the infrastructure to allow FireGL cards to be set up in a CrossFire configuration. The 'slave' graphics card needed to be from the same family as the 'master'.
An example of a limitation in regard to a Master-card configuration would be the first-generation CrossFire implementation in the Radeon X850 XT Master Card. Because it used a compositing chip from Silicon Image (SiI 163B TMDS), the maximum resolution on an X850 CrossFire setup was limited to 1600×1200 at 60 Hz, or 1920×1440 at 52 Hz. This was considered a problem for CRT owners wishing to use CrossFire to play games at high resolutions, or owners of Widescreen LCD monitors. As many people found a 60 Hz refresh rate with a CRT to strain one's eyes, the practical resolution limit became 1280×1024, which did not push CrossFire enough to justify the cost. The next generation of CrossFire, as employed by the X1800 Master cards, used two sets of compositing chips and a custom double density dual-link DVI Y-dongle to double the bandwidth between cards, raising the maximum resolution and refresh rate to far higher levels.
Second-generation (Software CrossFire)
When used with ATI's "CrossFire Xpress 3200" motherboard chipset, the 'master' card is no longer required for every "CrossFire Ready" card (with the exception of the Radeon X1900 series). With the CrossFire Xpress 3200, two normal cards can be run in a Crossfire setup, using the PCI-E bus for communications. This is similar to X1300 CrossFire, which also uses PCI Express, except that the Xpress 3200 had been built for low-latency and high-speed communication between graphics cards. While performance was impacted, this move was viewed as an overall improvement in market strategy, because Crossfire Master cards were expensive, in very high demand, and largely unavailable at the retail level.
Although the CrossFire Xpress 3200 chipset is indeed capable of CrossFire through the PCI-e bus for every Radeon series below the X1900s, the driver accommodations for this CrossFire method has not yet materialized for the X1800 series. ATI has said that future revisions of the Catalyst driver suite will contain what is required for X1800 dongleless CrossFire, but has not yet mentioned a specific date.
Current generation (CrossFireX)
With the release of the Radeon X1950 Pro (RV570 GPU), ATI has completely revised CrossFire's connection infrastructure to further eliminate the need for past Y-dongle/Master card and slave card configurations for CrossFire to operate. ATI's CrossFire connector is now a ribbon-like connector attached to the top of each graphics adapter, similar to nVidia's SLI bridges, but different in physical and logical natures. As such, Master Cards no longer exist, and are not required for maximum performance. Two dongles can be used per card; these were put to full use with the release of CrossFireX. Radeon HD 2900 and HD 3000 series cards use the same ribbon connectors, but the HD 3800 series of cards only require one ribbon connector, to facilitate CrossFireX. Unlike older series of Radeon cards, different HD 3800 series cards can be combined in CrossFire, each with separate clock control.
Since the release of the codenamed Spider desktop platform from AMD on November 19, 2007, the CrossFire setup has been updated with support for a maximum of four video cards with the 790FX chipset; the CrossFire branding was then changed to "ATI CrossFireX". The setup, which, according to internal testing by AMD, will bring at least 3.2x performance increase in several games and applications which required massive graphics capabilities of the computer system, is targeted to the enthusiast market.
A later development to the CrossFire infrastructure includes a dual GPU solution with on-board PCI-E bridge that was released in early 2008, the Radeon HD 3870 X2 and later in Radeon HD 4870 X2 graphics cards, featuring only one CrossFire connector for dual card, four GPU scalability.
An earlier CrossFireX and chipset compatibility chart is shown here: The latest compatibility chart, as of March 2012, shows AMD 890, 990 and A75 chipsets — and many Intel chipsets including Z68 and X79 chipsets — as being compatible with CrossFireX; it also shows which GPU cards (in the HD 5750 / 6750 / 7750, HD 5770 / 6770 / 7770, and HD 58 / 59 / 68 / 69 / 78 / 79 series) may be paired with an external bridge (the new HD 7750 and HD 7770 cards may be paired without an external bridge).
Hybrid CrossFireX / Dual Graphics
There is also a “hybrid” mode of CrossFireX which combines on-board graphics using the AMD northbridge architecture with selected graphic cards. The current generation is called Hybrid CrossFireX and is available for motherboards with integrated AMD chipsets in the 7 and 8 series IGPs, referred to as Hybrid CrossFireX. It allows combining discrete video cards ( ) and the IGP for increased performance.  This combination results in power-savings when simple or 2D graphics are used and performance increases of 25% to over 200% in 3D graphics over using a non CrossFire option.  As of March 2012, it appears that this is now called "AMD Radeon Dual Graphics" and means using A-series Fusion APUs together with video cards.
Comparisons to Nvidia SLI
- CrossFire can be implemented with varying-GPU cards of the same generation (this is in contrast to Nvidia's SLI, which generally only works if all cards have the same GPU). This allows buyers who have varying budgets over time to purchase different cards and still get the benefits of increased performance. With the latest generation cards, they will only crossfire with other cards in their sub series. For example, GPU in the same series can be crossfired with each other. So a 5800 series GPU (e.g. a 5830) can run together with another 5800 series GPU (e.g. 5870). However GPUs not in the same hundred series cannot be crossfired successfully (e.g. a 5770 cannot run with a 5870).
- ATI CrossFire configurations can run many monitors of varying size and resolution, while SLI only allows three monitors. The exception being Nvidia Surround which enables connection of up to four 2D displays and three 3D displays, although all displays must be the same resolution for this to work.
- The first generation CrossFire implementations (the Radeon X800 to X1900 series) require an external y-cable/dongle to operate in CrossFire mode due to the PCI-e bus not being able to provide enough bandwidth to run CrossFire without losing a significant amount of performance.
- In some cases CrossFire doesn't improve 3D performance – in some extreme cases, it can lower the framerate due to the particulars of an application's coding. This is also true for Nvidia's SLI, as the problem is inherent in multi-GPU systems. This is often witnessed when running an application at low resolutions.
- When using CrossFire with AFR, the subjective framerate can often be lower than the framerate reported by benchmarking applications, and may even be poorer than the frame rate of its single-GPU equivalent. This phenomenon is known as micro stuttering and also applies to SLI since it's inherent to multi-GPU configurations.
- Scalable Link Interface
- Comparison of ATI chipsets
- Comparison of AMD chipsets
- Micro stuttering
- Hybrid CrossFireX
- "ATI Launches Crossfire... Finally". Slashdot. 26 September 2005. Retrieved 28 December 2009.
- Tech Report article on CrossFire
- HardOCP article on CrossFire
- Anandtech article on the Xpress 3200
- bit-tech review of the HD 3870, retrieved January 25, 2008
- Earlier AMD CrossFireX and Chipset Compatibility Chart
- Latest AMD CrossFireX and Chipset Compatibility Chart
- "Combination Options Chart". Retrieved 22 September 2010.
- "ATI CrossFireX™ | GAME.AMD.COM". AMD. Retrieved 23 September 2010.
- Wikipedia's page on ATI Hybrid Graphics As of 23 September 2010 Wiki link refers to two discreet cards+IGP, but unable to verify this on AMD website and it still seems unsubstantiated after reading a Google translation of the article
- Triple Hybrid CrossfireX working AMD forums, retrieved 23 September 2010
- "AMD 790GX Chipset". AMD. Retrieved 22 September 2010.
- Bell, Brandon (4 March 2008). "AMD CrossFireX and Hybrid Graphics Performance Preview". Retrieved 23 September 2010.
- Toepelt, Bert (4 March 2008). "Benchmark Analysis - 65% More Performance Through Hybrid-Crossfire". Tom's Hardware. Retrieved 23 September 2010.
- Raffael Vötter (2008-02-08). "Video proof: Micro stuttering may destroy the performance gains from current multi GPU technologies". PC Games Hardware Online. Retrieved 2009-11-03.
- ATI's CrossFire official site
- Hardocp.com's CrossFire preview
- Slashdot coverage on the release of the system