The classical Carnot heat engine
An adiabatic process is a process that occurs without the transfer of heat or matter between a system and its surroundings. A key concept in thermodynamics, adiabatic transfer provides a rigorous conceptual basis for the theory used to expound the first law of thermodynamics. It is also key in a practical sense, that many rapid chemical and physical processes are described using the adiabatic approximation; such processes are usually followed or preceded by events that do involve heat transfer.
Adiabatic processes are primarily and exactly defined for a system contained by walls that are completely thermally insulating and impermeable to matter; such walls are said to be adiabatic. An adiabatic transfer is a transfer of energy as work across an adiabatic wall or sector of a boundary.
Approximately, a transfer may be regarded as adiabatic if it happens in an extremely short time, so that there is no opportunity for significant heat exchange.
- 1 Description
- 2 Adiabatic heating and cooling
- 3 Ideal gas (reversible process)
- 4 Graphing adiabats
- 5 Etymology
- 6 Usage of the word adiabatic
- 7 See also
- 8 References
- 9 External links
For an adiabatic transfer of energy as work, the notation Q = 0 indicates that no energy is transferred as heat across the adiabatic boundary or wall.
An ideal or fictive quasi-static adiabatic transfer of energy as work that occurs without friction or viscous dissipation within the system is said to be isentropic, with ΔS = 0.
For a natural process of transfer of energy as heat, driven by a finite temperature difference, entropy is both transferred with the heat and "generated" within the system. Such a process is neither adiabatic nor isentropic, having Q > 0, and ΔS > 0 according to the second law of thermodynamics.
A natural adiabatic process is irreversible and is not isentropic. Adiabatic transfer of energy as work can be analyzed into two extreme component kinds. One extreme kind is without friction or viscous dissipation within the system, and this is usually pressure-volume work, denoted customarily by P dV. This is an ideal that does not occur unaccompanied in nature. It may be regarded as "reversible". The other extreme kind is isochoric work, for which dV = 0, solely through friction or viscous dissipation within the system. Isochoric work is irreversible. The second law of thermodynamics observes that a natural process of transfer of energy as work, exactly considered, always consists at least of isochoric work and often of both of these extreme kinds of work. Every natural process, adiabatic or not, exactly considered, is irreversible, with ΔS > 0, however slight may be the friction or viscosity.
Adiabatic heating and cooling
Adiabatic heat occurs when the pressure of a gas is increased from work done on it by its surroundings, e.g., a piston compressing a gas contained within an adiabatic cylinder. This finds practical application in Diesel engines which rely on the lack of quick heat dissipation during their compression stroke to elevate the fuel vapor temperature sufficiently to ignite it.
Adiabatic heating also occurs in the Earth's atmosphere when an air mass descends, for example, in a katabatic wind or Foehn or chinook wind flowing downhill over a mountain range. When a parcel of air descends, the pressure on the parcel increases. Due to this increase in pressure, the parcel's volume decreases and its temperature increases, thus increasing the internal energy.
Adiabatic cooling occurs when the pressure of a substance is decreased as it does work on its surroundings. Adiabatic cooling occurs in the Earth's atmosphere with orographic lifting and lee waves, and this can form pileus or lenticular clouds if the air is cooled below the dew point. When the pressure applied on a parcel of air decreases, the air in the parcel is allowed to expand; as the volume increases, the temperature falls and internal energy decreases.
Adiabatic cooling does not have to involve a fluid. One technique used to reach very low temperatures (thousandths and even millionths of a degree above absolute zero) is adiabatic demagnetisation, where the change in magnetic field on a magnetic material is used to provide adiabatic cooling. Also, the contents of an expanding universe (to first order) can be described as an adiabatically cooling fluid. (See - Heat death of the universe)
In practice, no process is truly adiabatic. Many processes rely on a large difference in time scales of the process of interest and the rate of heat dissipation across a system boundary, and thus are approximated by using an adiabatic assumption. There is always some heat loss, as no perfect insulators exist.
Ideal gas (reversible process)
The mathematical equation for an ideal gas undergoing a reversible (i.e., no entropy generation) adiabatic process is
where P is pressure, V is volume, and
being the specific heat for constant pressure, being the specific heat for constant volume, is the adiabatic index, and is the number of degrees of freedom (3 for monatomic gas, 5 for diatomic gas and collinear molecules e.g. carbon dioxide).
For a monatomic ideal gas, , and for a diatomic gas (such as nitrogen and oxygen, the main components of air) . Note that the above formula is only applicable to classical ideal gases and not Bose–Einstein or Fermi gases.
For reversible adiabatic processes, it is also true that
where T is an absolute temperature.
This can also be written as
Example of adiabatic compression
Let's now look at a common example of adiabatic compression- the compression stroke in a gasoline engine. We will make a few simplifying assumptions: that the uncompressed volume of the cylinder is 1000 cm3 (one liter), that the gas within is nearly pure nitrogen (thus a diatomic gas with five degrees of freedom and so = 7/5), and that the compression ratio of the engine is 10:1 (that is, the 1000 cm3 volume of uncompressed gas will compress down to 100 cm3 when the piston goes from bottom to top). The uncompressed gas is at approximately room temperature and pressure (a warm room temperature of ~27 ºC or 300 K, and a pressure of 1 bar ~ 100 kPa, or about 14.7 PSI, or typical sea-level atmospheric pressure).
so our adiabatic constant for this experiment is about 1.58 billion.
The gas is now compressed to a 100cc volume (we will assume this happens quickly enough that no heat can enter or leave the gas). The new volume is 100 ccs, but the constant for this experiment is still 1.58 billion:
so solving for P:
or about 362 PSI or 24.5 atm. Note that this pressure increase is more than a simple 10:1 compression ratio would indicate; this is because the gas is not only compressed, but the work done to compress the gas has also heated the gas and the hotter gas will have a greater pressure even if the volume had not changed.
We can solve for the temperature of the compressed gas in the engine cylinder as well, using the ideal gas law. Our initial conditions are 100,000 pa of pressure, 1000 cc volume, and 300 K of temperature, so our experimental constant is:
We know the compressed gas has V = 100 cc and P = 2.50E6 pascals, so we can solve for temperature by simple algebra:
That's a final temperature of 751 K, or 477 °C, or 892 °F, well above the ignition point of many fuels. This is why a high compression engine requires fuels specially formulated to not self-ignite (which would cause engine knocking when operated under these conditions of temperature and pressure), or that a supercharger and inter cooler to provide a lower temperature at the same pressure would be advantageous. A diesel engine operates under even more extreme conditions, with compression ratios of 20:1 or more being typical, in order to provide a very high gas temperature which ensures immediate ignition of injected fuel.
Adiabatic free expansion of a gas
For an adiabatic free expansion of an ideal gas, the gas is contained in an insulated container and then allowed to expand in a vacuum. Because there is no external pressure for the gas to expand against, the work done by or on the system is zero. Since this process does not involve any heat transfer or work, the First Law of Thermodynamics then implies that the net internal energy change of the system is zero. For an ideal gas, the temperature remains constant because the internal energy only depends on temperature in that case. Since at constant temperature, the entropy is proportional to the volume, the entropy increases in this case, therefore this process is irreversible.
Derivation of continuous formula for adiabatic heating and cooling
The definition of an adiabatic process is that heat transfer to the system is zero, . Then, according to the first law of thermodynamics,
where dU is the change in the internal energy of the system and δW is work done by the system. Any work (δW) done must be done at the expense of internal energy U, since no heat δQ is being supplied from the surroundings. Pressure-volume work δW done by the system is defined as
However, P does not remain constant during an adiabatic process but instead changes along with V.
It is desired to know how the values of dP and dV relate to each other as the adiabatic process proceeds. For an ideal gas the internal energy is given by
Differentiating Equation (3) and use of the ideal gas law, , yields
Equation (4) is often expressed as because .
Now substitute equations (2) and (4) into equation (1) to obtain
and divide both sides by PV:
After integrating the left and right sides from to V and from to P and changing the sides respectively,
Exponentiate both sides, and substitute with , the heat capacity ratio
and eliminate the negative sign to obtain
Derivation of discrete formula
The change in internal energy of a system, measured from state 1 to state 2, is equal to
At the same time, the work done by the pressure-volume changes as a result from this process, is equal to
Since we require the process to be adiabatic, the following equation needs to be true
By the previous derivation,
Rearranging (4) gives
Substituting this into (2) gives
Using the ideal gas law and assuming a constant molar quantity (as often happens in practical cases),
By the continuous formula,
Substituting into the previous expression for ,
Substituting this expression and (1) in (3) gives
An adiabat is a curve of constant entropy on the P-V diagram. Properties of adiabats on a P-V diagram are:
- Every adiabat asymptotically approaches both the V axis and the P axis (just like isotherms).
- Each adiabat intersects each isotherm exactly once.
- An adiabat looks similar to an isotherm, except that during an expansion, an adiabat loses more pressure than an isotherm, so it has a steeper inclination (more vertical).
- If isotherms are concave towards the "north-east" direction (45 °), then adiabats are concave towards the "east north-east" (31 °).
- If adiabats and isotherms are graphed severally at regular changes of entropy and temperature, respectively (like altitude on a contour map), then as the eye moves towards the axes (towards the south-west), it sees the density of isotherms stay constant, but it sees the density of adiabats grow. The exception is very near absolute zero, where the density of adiabats drops sharply and they become rare (see Nernst's theorem).
The following diagram is a P-V diagram with a superposition of adiabats and isotherms:
The isotherms are the red curves and the adiabats are the black curves.
The adiabats are isentropic.
Volume is the horizontal axis and pressure is the vertical axis.
The term adiabatic//, literally means 'not to be passed through'. It is formed from the ancient Greek privative "α" ("not") + διαβατός, "able to be passed through", in turn deriving from διὰ- ("through"), and βαῖνειν ("to walk, go, come"), thus ἀδιάβατος . According to Maxwell, and to Partington, the term was introduced by Rankine.
The etymological origin corresponds here to an impossibility of transfer of energy as heat and of transfer of matter across the wall.
Usage of the word adiabatic
This present article is written from the viewpoint of macroscopic thermodynamics, and the word adiabatic is used in this article in the traditional way of thermodynamics, introduced by Rankine. It is pointed out in the present article that, for example, if a compression of a gas is rapid, then there is little time for heat transfer to occur, even when the gas is not adiabatically isolated. In this sense, a rapid compression of a gas is approximately adiabatic even when the gas is not adiabatically isolated.
Quantum statistical theory, however, uses the word adiabatic in an almost opposite sense. On one hand in that theory, if a perturbative element of compressive work is done almost infinitely slowly (that is to say quasi-statically or virtually reversibly) on an adiabatically isolated mass of gas, it is said to have been done adiabatically. The idea is that the shapes of the eigenfunctions change slowly and continuously, so that no quantum jump is triggered, and the change is virtually reversible. The occupation numbers are unchanged, though the energy levels of one-to-one corresponding, pre-and post-change, eigenstates are changed. Thus a perturbative element of work has been done without heat transfer and without introduction of random change within the system.
On the other hand in that theory, if the perturbative element of compressive work is done rapidly, the compressing piston imparts energy by collision to the molecules of the gas. This randomly changes the occupation numbers of the eigenstates, as well as changing their shapes. Further collisions of gas molecules involve viscosity, with further random changes in occupation numbers. In that theory, such a rapid change is said not to be 'adiabatic', and the contrary word 'diabatic' is even applied to it. One might guess that Clausius, if he were confronted with this, would perhaps have said that internal work was done and that, in the language he used, 'heat was generated though not transferred'.
In classical thermodynamics, such a rapid change would still be called adiabatic because the system is adiabatically isolated, and there is no transfer of energy as heat. The strong irreversibility of the change, with viscosity, does not alter this classical usage. But the words are used differently in quantum theory, as stated just above.
Thus for a mass of gas, in macroscopic thermodynamics, words are so used that a compression is sometimes approximately said to be adiabatic if it is sufficiently rapid, even if the gas is not adiabatically isolated. But in quantum statistical theory, a compression is said not to be adiabatic if it is sufficiently rapid, even if the gas is adiabatically isolated.
- Cyclic process
- First law of thermodynamics
- Heat burst
- Isobaric process
- Isenthalpic process
- Isentropic process
- Isochoric process
- Isothermal process
- Polytropic process
- Entropy (classical thermodynamics)
- Quasistatic process
- Total air temperature
- Magnetic refrigeration
- Carathéodory, C. (1909). Untersuchungen über die Grundlagen der Thermodynamik, Mathematische Annalen, 67: 355–386, doi:10.1007/BF01450409. A translation may be found here. Also a mostly reliable translation is to be found at Kestin, J. (1976). The Second Law of Thermodynamics, Dowden, Hutchinson & Ross, Stroudsburg PA.
- Bailyn, M. (1994). A Survey of Thermodynamics, American Institute of Physics Press, New York, ISBN 0-88318-797-3, p. 21.
- Münster, A. (1970), Classical Thermodynamics, translated by E.S. Halberstadt, Wiley–Interscience, London, ISBN 0-471-62430-6, p. 45.
- Kavanagh, J.L.; Sparks R.S.J. (2009). "Temperature changes in ascending kimberlite magmas". Earth and Planetary Science Letters (Elsevier) 286 (3–4): 404–413. Bibcode:2009E&PSL.286..404K. doi:10.1016/j.epsl.2009.07.011. Retrieved 18 February 2012.
- Adiabatic Processes
- Liddell, H.G., Scott, R. (1940). A Greek-English Lexicon, Clarendon Press, Oxford UK.
- Maxwell, J.C. (1871), Theory of Heat (first ed.), London: Longmans, Green and Co., p. 129
- Rankine, W.J.McQ. (1866). On the theory of explosive gas engines, The Engineeer, July 27, 1866; at page 467 of the reprint in Miscellaneous Scientific Papers, edited by W.J. Millar, 1881, Charles Griffin, London.
- Partington, J.R. (1949), An Advanced Treatise on Physical Chemistry., volume 1, Fundamental Principles. The Properties of Gases, London: Longmans, Green and Co., p. 122.
- Silbey, Robert J.; et al. (2004). Physical chemistry. Hoboken: Wiley. p. 55. ISBN 978-0-471-21504-2.
- Broholm, Collin. "Adiabatic free expansion." Physics & Astronomy @ Johns Hopkins University. N.p., 26 Nov. 1997. Web. 14 Apr. *Nave, Carl Rod. "Adiabatic Processes." HyperPhysics. N.p., n.d. Web. 14 Apr. 2011. .
- Thorngren, Dr. Jane R.. "Adiabatic Processes." Daphne – A Palomar College Web Server. N.p., 21 July 1995. Web. 14 Apr. 2011. .