Chrysler 1.8, 2.0 & 2.4 engine
|This article needs additional citations for verification. (December 2013)|
|1.8, 2.0 & 2.4 engine|
2.4 L engine
|Cylinder block alloy||Cast Iron|
|Cylinder head alloy||Aluminum|
|Fuel system||Sequential multi-point fuel injection|
|Oil system||Wet sump|
|Successor||Chrysler World engine|
The Chrysler 1.8, 2.0, and 2.4 are inline-4 engines designed originally for the Dodge and Plymouth Neon compact car. These engines were loosely based on their predecessors, the Chrysler 2.2 & 2.5 engine, sharing the same 87.5 mm bore. The DOHC head was developed by Chrysler with input from the Chrysler-Lamborghini team that developed the Chrysler/Lamborghini Formula 1 V12 engine in the early 1990s.
The 2.0 and 2.4 variants were built at Saltillo Engine in Ramos Arizpe, Coahuila, Mexico. The 1.8 and 2.0 was also built at Trenton Engine in Trenton, Michigan, United States.
The EBD, is a 1,796 cc (109.6 cu in) under-bored variant of the 2.0 L engine. This engine features a square 83 mm (3.3 in) bore and stroke with a 10.0:1 compression ratio. This engine was built at the Trenton Engine Plant for use in export market (non-US) Chrysler Neons. It produces 86 kW (115 hp) at 5750 rpm and 151 newton metres (111 lb·ft) at 4950 rpm and meets Euro III emission standards.
- 1997-1999 Chrysler Neon
||This section may be too technical for most readers to understand. (December 2013)|
The 1,996 cc (1.996 L; 121.8 cu in) version of the engine was the first offered. Production began in 1994 in Trenton, MI, and it was used in many Chrysler Corporation vehicles. It is available in both SOHC and DOHC 4-valve versions. The engine features a cast iron block, with pistons with shallow crowns to save weight.
The block uses a bedplate featuring a perimeter wall with transverse webbings for durability and quiet operation at high rpm's. The pistons are attached to fracture-split forged powdered metal connecting rods using semi-floating press-fit pins. A gerotor oil pump is driven directly from the crankshaft on the front of the engine. A reinforced rubber timing belt is used to drive the valvetrain. Early production 2.0 L engines used a hydraulic tensioner to tension the timing belt. 2000 and 2001 engines received a mechanical spring-loaded tensioner that tended to wear out prematurely, causing serious valve and piston damage upon belt failure due to the interference design of the engine. 2002+ engines utilized a different mechanical tensioner. The water pump is driven from the timing belt, with the water pump housing cast partially into the engine block itself.
1995 model year engines had three features that set them apart from later model year engines. The positive crankcase ventilation (PCV) system utilized a plastic oil separator box that was vented directly to the block itself; the breather hose and PCV valve hoses attached to the box, and connected to the induction system. Later model year engines featured a PCV system that was molded to the cylinder head valve cover. The second feature was internal in nature - the crankshaft main bearings were keyed into the bedplate on the right rear of each transverse web. Later model years featured keys machined on the right front of each web. These considerations are important when considering a rebuild or replacement of this engine in a given vehicle. The third feature would be a slightly bigger cam that was changed on 1996 and up SOHC vehicles due to a rough idle when the A/C was on. This 1995 cam is now being sold by dealers as a power upgrade for 1996 and up SOHC engines, but it can also easily be found at auto recyclers or salvage yards for a cheap price.
2002 and earlier model year engines featured a one-piece cast nodular iron crankshaft with counterweights present on either side of each crank pin. A crankshaft tone wheel was present between number 1 and number 2 connecting rod pins, and was machined such that a Hall-effect magnetic pickup mounted to the engine block could read the position of the crankshaft as it rotates during normal operation. 2003 and later model year engines switched to a two-piece crankshaft. The tone wheel was re-engineered to attach to the crankshaft using three bolts, had a tone pattern that was substantially different from previous model year engines, and was moved to the rear of the crankshaft. For this reason, these engines are generally not interchangeable between the 2002- and 2003+ model years.
Up to late 1999, this engine type suffered from oil leaks between the block and cylinder head. The threads for the head bolts near the 4th cylinder were bored too shallow at the factory, preventing the head from properly sealing. The oil restrictor in the composite gasket would separate from the gasket causing a leak. Chrysler Corporation used several different designs of composite material head gasket in an attempt to solve this problem. In 1998, a thicker multi-layer steel head gasket was introduced that eliminated this oil leak. It can be identified by a small metal tab with a hole through its center sticking out between the block and head between the 2nd and 3rd cylinders.
- General Specifications
- Number of Cylinders: 4
- Cylinder Configuration: In-line
- Number of Valves: 16 (4 per cylinder)
- Fuel Delivery: Sequential Multi-Port Fuel Injection
- Bore: 87.5 mm (3.44 in)
- Stroke: 83.0 mm (3.27 in)
- Displacement: 2.0 L (1996 cc or 122 cid)
- Redline: 6500 rpm
- Rev Limiter: 6750 rpm
The A588 is the SOHC version found in most post 2001 Chrysler products. The ECB SOHC version, found in earlier models, is identical except for the crank trigger wheel. When equipped with the newer crank wheel for the new NGC engine computer, the A588 version cannot be directly transplanted into a vehicle originally equipped with the earlier style engine using an SBEC (Single Board Engine Controller). Output is 132 hp (98 kW) SAE (98 kW) at 5600 rpm with 130 lb·ft (177 N·m) of torque at 4600 rpm. It has an aluminum SOHC cylinder head. It uses a reinforced plastic intake manifold (although a few of the 1995 and 1996 engines received an aluminum intake manifold due to a shortage of the plastic parts). They were painted black, but it's easy to see the casting marks and prints on the manifold. The aluminum version is prized among enthusiasts as it's easy to port and polish for increased flow characteristics.
- Compression Ratio: 9.8:1
- Camshaft Configuration: SOHC
- Power: 132 hp (98 kW) @ 5600 rpm
- Torque: 130 lb·ft (180 N·m) @ 4600 rpm
The Magnum SOHC version, code ECH, develops 150 hp (110 kW) SAE (111 kW) at 6500 rpm, and 135 lb·ft (184 N·m) of torque at 4800 rpm. Chief differences between this version and the A588 include a cast aluminum SOHC cylinder head that more easily passes exhaust gases than the base engine, a camshaft that is optimized for higher engine rpm's, a factory welded exhaust short-tube header in lieu of a cast exhaust manifold, and a two-piece intake manifold. This manifold features unequal-length intake runners that are switched during engine operation by an electric actuator that controls butterfly-type valves in the shorter intake runners. The longer runners are always open, and provide a mild supercharging effect due to their length between 3000 rpm and 4800 rpm. The shorter runners, open from 4800 rpm to redline at wide-open throttle, also provide a tuned resonance effect due to their length. The shorter runners are also opened at wide-open throttle below 3000 rpm to provide an intake path to each cylinder that is as free-flowing as possible.
- Compression Ratio: 9.8:1
- Camshaft Configuration: SOHC
- Power: 150 hp (110 kW) @ 6500 rpm
- Torque: 135 lb·ft (183 N·m) @ 4800 rpm
- Rev-Limiter: 6750 rpm
The DOHC ECC 2.0 produces 150 hp (110 kW) SAE at 6500 rpm with 133 lb·ft (180 N·m) of torque at 4800 rpm. It has a cast iron engine block and aluminum DOHC cylinder head. It uses SFI fuel injection, has 4 valves per cylinder with roller rocker arms and features fracture-split forged powder metal connecting rods, a one-piece cast camshaft, and an aluminum intake manifold.
The version used in the PT Cruiser (non-US) and Dodge Neon features a cylinder head with the intake ports facing the front of the vehicle, like the SOHC A588. Versions (420A) used in the Dodge-designed chassis, such as the Dodge Avenger and Mitsubishi Eclipse, have the intake ports facing the rear of the vehicle. Most other specifications are identical, however, and even some head components (such as the valve cover) are compatible.
- Chrysler PT Cruiser (non-US) (ECC)
- Dodge Avenger/Chrysler Sebring (1995–1999) (420A)
- Dodge Neon/Plymouth Neon (1995–1999) (ECC)
- Mitsubishi Eclipse/Eagle Talon (second generation, 1995–1999) (420A)
- Compression Ratio: 9.6:1
- Camshaft Configuration: DOHC
- Displacement: 1996 cc (121.8 CID)
- Power: 150 hp (110 kW) @ 6000 rpm
- Torque: 133 lb·ft (180 N·m) @ 4800 rpm
- Rev-Limiter: 7200 rpm
2.4 and 2.4 Turbo
The Neon itself never carried a naturally aspirated 2.4L engine in its lineup, but a 150 hp (110 kW), 167 lb·ft (226 N·m) N/A version was used in Chrysler's JA, JX, and JR platform cars from 1995 to 2006 along with the Jeep Liberty from 2002 to 2005 and the Dodge Caravan and Plymouth Voyager from 1996 to 2000. The code for this engine was EDZ. As with some other engines of various architecture used in Jeeps, EDZs used in the Liberty carried Chrysler's PowerTech name. Unlike the 1.8/2.0L engines the 2.4L is a non-interference design.
The SRT-4 performance variant utilized a 2.4L Turbo. The turbocharged EDV/EDT is similar to the regular EDZ. Output is 245 hp (183 kW) SAE (172 kW) at 5300 rpm with 260 lb·ft (339 N·m) of torque at 2200-4400 rpm. This engine, code A855, has a cast iron partially open deck block and split crankcase. It uses an 8.1:1 compression ratio with Mahle cast eutectic aluminum alloy pistons, forged connecting rods with cracked caps and threaded-in 9 mm rod bolts, and a cast high-hardness steel crankshaft. The cylinder head is cast aluminum, with the cylinder heads being a 48-degree pent-roof design with a partial cloverleaf between the intake valves. The valves are actuated by hydraulically adjusted rocker arms with roller cam followers.
The SRT-4 and PT Cruiser Turbo use the same engine block and heads The intake manifold, turbo plumbing, and intercooler are all different. The cast-aluminum 8-row Valeo intercooler is mounted in the front, and the reverse-rotation Mitsubishi TD04LR-16Gk turbocharger has a 6 cm2 (1 sq in) turbine inlet. The turbocharger compressor housing features a built-in bypass valve, and the turbo housing is cast into the exhaust manifold with a loop-around flow pattern. The stock SRT-4 has a maximum boost level of 15 psi (100 kPa)
2.4 N/A applications:
- 1995–1998, 2000 Chrysler Cirrus
- 1995–2006 Chrysler Sebring
- 1995–2006 Dodge Stratus
- 1996-2007 Dodge Caravan
- 2002–2005 Jeep Liberty
- 2003-2006 Jeep Wrangler
- 1996-2000 Plymouth Voyager
- 1996–2000 Plymouth Breeze
- 2001-2010 Chrysler PT Cruiser
- 2007-2010 GAZ-31105 Volga
2.4 Turbo Applications:
- McCraw, Jim (1993). "The Chrysler/Lamborghini Formula 1 V12: REVS R US!". High Performance Mopar 7 (7): 50–55.