Chrysler Slant-6 engine
|This article needs additional citations for verification. (March 2007)|
|Chrysler Slant Six (G, RG) Engine|
|Displacement||170 cu in (2.8 L)
198 cu in (3.2 L)
225 cu in (3.7 L)
|Cylinder block alloy||Cast iron
|Cylinder head alloy||Cast iron|
|Compression ratio||8.2:1 - 8.5:1 (nominal)|
|Oil system||Full pressure w/full-flow filter & gerotor oil pump|
|Cooling system||Jacketed block, Water pump to radiator|
The Slant-6 is a Chrysler automobile engine, known within Chrysler as the G-engine. It is a inline-6 piston engine designed such that the cylinders are inclined at a 30-degree angle from vertical. The 30° inclination of the Slant-6 gives a lower height overall engine package, which enabled vehicle stylists to lower hoodlines, and also made room for the water pump to be mounted with a lateral offset, significantly shortening the engine's overall length. In addition, the slanted cylinder block provides ample space under the hood for intake and exhaust manifolds with runners of longer and more nearly equal length compared to the rake- or log-style manifolds typical of other inline engines. The Slant-6 manifold configuration gives relatively even distribution of fuel mixture to all cylinders, and presents less flow restriction. This, in turn, makes for relatively good airflow through the engine despite the intake and exhaust ports being on the same side of the head rather than in a crossflow arrangement.
The engine was a clean-sheet design, led by Willem Weertman, later Chrysler's chief engine designer. It was introduced in two piston displacement sizes in 1960: The 170-cubic-inch (2.8-litre) "LG" (Low-G, referring to the relatively short engine block casting and crankshaft stroke) in the Valiant, and the 225-cubic-inch (3.7-litre) "RG" (Raised-G, referring to the relatively tall engine block casting and crankshaft stroke) in full-size Plymouth and Dodge Dart models. In 1960, the engine was called the "30-D Economy Six" engine by Plymouth marketers, referring to the 30° cylinder block angle.
The G-engine was offered in various configurations in the North American market until 1983 in cars, 1987 in trucks, and 1991 for marine, agricultural, and industrial use. Replacement engines were still being built in Mexico as of 2000. In addition, the G-engine was used extensively by worldwide Chrysler divisions and subsidiaries in their locally produced vehicles. It was also widely purchased by other original equipment manufacturers for installation in commercial vehicles, agricultural and industrial equipment, and boats.
Hear a slant-6 engine
A 225 slant-6 engine in a 1965 Canadian Valiant starts and runs
|Problems playing this file? See media help.|
The G-engine gained a reputation for reliability and durability. The basic engine design is rigid and sturdy, in part because the engine was designed to be made of either iron or aluminum; an aluminum block was produced in 1961-1963, but most blocks were made of iron. The block is of a deep-skirt design, with the crankshaft axis well above the oil pan rails for structural rigidity. Although only four main bearings are used, they are of the same dimensions as those in the Hemi. Efficient cooling and lubrication systems, a favorable ratio of connecting rod length to stroke, and a massive forged steel crankshaft (on engines made through mid-1976) all contributed to the engine's strength.
The G-engine gave better performance than its competitors at its 1960 introduction, and generally kept up through the '60s and early '70s, though engines like the Pontiac OHC Six bested the performance of most versions of the slant-6, and after an early factory racing program was discontinued by 1962, the slant-6 did not receive much performance development; most slant-6s were equipped with a single 1-barrel carburetor. Starting in the early 1970s, primitive emission controls adversely affected driveability and power, though a version of the 2-barrel carburetor package first released for marine and export markets in 1967 was offered in North America from 1977 to 1983 under the "Super Six" name; performance figures were only slightly higher, but driveability was substantially improved. Other Chrysler engines were released with more advanced combustion chambers, electronic fuel injection, and other modern improvements, but the length of the slant six precluded its use in Chrysler's front-drive cars, and a new 3.9 litres (238 cubic inches) V6 engine created by lopping two cylinders off the corporate 318-cubic-inch (5.2-litre) LA V8 engine was devised for use in the new Dodge Dakota compact pickup truck for 1986. The Slant-6 engine was dropped from the rest of the Dodge truck line at the end of the 1987 model year, replaced by the 3.9 V6.
- 1 Significant production changes
- 2 Configuration variants
- 3 Applications
- 4 See also
- 5 References
- 6 External links
Significant production changes
- The combustion chamber shape was slightly modified for 1967 to promote more complete combustion and reduce exhaust emission toxicity.
- All G engines used forged steel crankshafts until the middle of model year 1976, when a less costly cast-iron crankshaft was introduced. The cast crankshaft uses a different block, different main and connecting rod bearings and different connecting rods.
- The counterbore in the rear flange of the crankshaft was a 1 1⁄4-inch diameter until 1967. For 1968, it was enlarged to 1 1⁄2 inches. This difference has implications when swapping engines and automatic transmissions across this date line.
- All G-engines used solid valve lifters through the 1980 model year, with the exception of a small production test of hydraulic lifters in the 1978 model year. For model year 1981, all North American G-engines received top-fed hydraulic lifters. Retrofitment in both directions is possible.
- Emission control devices and systems, carburetor make and specification, and engine assembly details changed over the years to comply with market requirements and preferences.
- Electronic ignition, which had been made available on V8 engines late in 1971, was made standard equipment on all engines including the RG in 1973.
- Induction-hardened exhaust valve seats and upgraded exhaust valves were made standard in 1973 to withstand prolonged operation on no-lead fuel.
The 170 engine was offered in model years 1960 through 1969 in North America, and through 1971 for export markets. The first vehicle to offer the 170 slant-6 was the 1960 Valiant. The engine has a bore of 3.40 in (86.4 mm) and a stroke of 3.125 in (79.4 mm) for an actual displacement of 170.2 cu in (2.8 L). Connecting rod length is 5.669 in (144.0 mm). The "LG" low-deck block was unique to the 170 engine.
The 198 was introduced in the North American market for model year 1970 as a more powerful base-model engine than the previous 170 engine. The increased displacement gave improved vehicle performance and lower manufacturing cost, for it was achieved with the tall RG block also used with the 225 engine by installing a crankshaft with 3.64 in (92.5 mm) stroke and connecting rods 7.006 in (178.0 mm) long, for an actual displacement of 198.3 cu in (3.2 L). In this manner, manufacturing costs were eliminated that had been caused by previously using two different blocks for the two different available sizes of slant-6 engine. The 198 engine was available through the 1974 model year.
The 225 used the RG (tall) block with a 3.40 in (86.4 mm) bore, a 4.125 in (104.8 mm) stroke, and 6.699 in (170.2 mm) connecting rods, for an actual displacement of 224.7 cu in (3.7 L). This undersquare geometry was a departure from the emerging trend towards oversquare engines, and gave the 225 exceptionally strong low-rpm torque characteristics. The large amount of torque available at low engine speeds caused the 225 to find favor not only as a responsive and driveable passenger car engine, but also in pickup and commercial trucks, school buses, motorhomes, forklifts, harvesters, swathers from the likes of John Deere and Massey-Ferguson, airplane tugs, and powerboats. The 225 was originally designed and introduced in 1960 for use in full-size models, and it eventually became the best known of the Slant Six engines.
Between late model year 1961 and early model year 1963, approximately 52,000 die-cast aluminum RG blocks were produced and installed in passenger cars. These open-deck blocks used integrally cast high-nickel iron cylinder liners, and bolt-in iron upper and lower main bearing caps. Internal components (crank, rods, pistons, etc.) were the same as used in the iron engine, and an iron cylinder head was used with a special copper-asbestos gasket. The aluminum block weighs about 80 lb (36 kg) less than the iron RG block.
Although serviceable examples can still be found, the aluminum RG tended to undergo delamination between the iron cylinder liner and the surrounding aluminum. Severe corrosion within the block is also commonly found because of the general tendency in the 1960s and '70s to fill cooling systems in summer with plain water without corrosion inhibitors. Moreover, the open-deck design and primitive head gasket technology are not sufficiently robust to withstand the increased seal demands of increased compression or forced induction.
Most G-engines were equipped with small-capacity carburetors and exhaust systems adequate for standard passenger car usage at low altitudes, but which tended to hamper maximum available performance at high altitudes, in heavy or race-purpose vehicles and/or where quicker acceleration was desired. To meet the demand for improved responsiveness, modified engine configurations were made available in various markets over the years.
The Hyper Pak was a parts package made available from 1960 through 1962 at Chrysler Corporation dealer parts counters. The parts were made available to comply with the regulations of sanctioning bodies for racing events in which Valiants had been entered by factory-backed teams: All parts used had to be "stock" parts, the definition of which meant that they were available through normal factory parts channels. The Hyper Pak consisted of a very-long-ram intake manifold meant to accept a Carter AFB 4-barrel carburetor, the AFB carburetor itself and an appropriate air cleaner, dual (front-3 and rear-3) cast-iron exhaust headers, a large-diameter exhaust Y-pipe to connect to these dual cast-iron headers, a larger muffler, a 276°-duration camshaft with appropriate valve springs and pushrods, a heavier-duty clutch, a manual choke control, a starter motor modification template and, in the full-race version of the package, high-compression pistons designed to increase the engine's compression ratio to 10.5 from the stock 8.5. The Hyper Pak was recommended for installation only on vehicles equipped with manual transmissions, for the camshaft was of such characteristics that a high idle speed was required to prevent engine stall-out. The Hyper Pak was primarily intended for competition driving, its road manners involving rough idling and poor cold-engine driveability, a high power band and poor fuel economy. But, in competition events, it proved unbeatable. Eight factory-backed Valiants entered the 1960 NASCAR compact car race at Daytona Beach, and humbled the competition; the Valiants came in first through eighth. After a similar performance the following year, the race was dropped. A high-fidelity reproduction of the Hyper Pak intake manifold was created by noted Slant-6 builder Doug Dutra in the late 1990s; subsequently the tooling was sold to a marketer of performance equipment for inline six-cylinder engines.
For the 1965–1968 model years, Chrysler Argentina equipped Valiant GT models with a system of dual 1-barrel Holley RX 7000 A carburetors and other engine specification changes. Claimed output was 180 bhp (130 kW), compared to the single-carburetor version of the engine producing 145 bhp (108 kW)
Export 2-barrel setup
For the 1967 model year, a 2-barrel carburetor setup was released for export production. This configuration, similar to that found on marine G-engines beginning in 1965, consisted of an iron intake manifold with open-plenum 2-barrel carburetor mounting pad, a Carter BBD carburetor, and associated air cleaner, linkage and plumbing changes. Also installed on these export 2-barrel engines was a slightly hotter camshaft (244° duration rather than 240°), and a distributor with modified advance curves. This engine, rated at 160 bhp (120 kW), was popular in Central and South America, South Africa, Australia and New Zealand. Driveability characteristics were generally superior to those of the 1-barrel engine, but to avoid cutting into sales of the more expensive V8 engine, this 2-barrel setup was not offered in the North American market. Of particular note is the automatic choke design found in this export 2-barrel setup. Most Chrysler products used remote automatic chokes, with a bimetal coil spring mounted on the exhaust manifold, exposed to exhaust heat and operating a pushrod which rotated the choke lever on the carburetor. The export 2-barrel setup used an integral heat-tube style automatic choke: Air heated by the exhaust manifold was routed to a round bakelite housing on the carburetor air horn, which contained a bimetal spring acting directly on the choke lever.
By the mid-1970s in the North American market, emission control regulations were reducing engine performance at the same time as safety regulations were making cars heavier. An increase in performance was required for the G-engine, so a 2-barrel setup was released for the 1976 model year. This was not the same as the export 2-barrel package; the intake manifold used a throttle-bored plenum rather than an open one, and had provisions for an EGR valve. The carburetor, a Carter BBD similar but not identical to the one used on Chrysler's 318 V8 engine, used a standard Chrysler-style remote automatic choke. A 2 1⁄4-inch exhaust headpipe was also provided, as well as 2-barrel-specific advance curves in the ignition distributor. This package, called "Super Six" by the marketing division, brought rated horsepower from 100 to 110 hp (75 to 82 kW) and torque from 170 to 180 lb·ft (230 to 244 N·m), but significantly improved throttle response and driveability while maintaining compliance with emission laws.
|This section requires expansion. (May 2013)|
Many companies have provided aftermarket performance equipment for the G-engine through the years. A wide selection of camshafts, intake manifolds, tubular and cast iron exhaust headers, various induction setups, ignition components, internal engine parts and accessories are still available on today's market.
Passenger cars, trucks, vans
- The Chrysler Slant Six Engine (170-198-225)
- Willem Weertman - Chrysler Chief Engineer, Engine Design and Development
- 1960 Plymouth Cars: Fins' Final Fling
- 1960 Plymouth advertisement in Life Magazine, October 1959
- Interview with Pete Hagenbuch, Chrysler engine development engineer
- Dutra, Doug (2001). "Aluminum Slant Six Engine Overview". Slant Six Forum. Retrieved 2012-06-14.