Ford Crown Victoria Police Interceptor
|This article needs additional citations for verification. (March 2011)|
|Ford Crown Victoria Police Interceptor
A second generation Ford Crown Victoria Police Interceptor of the New York City Police Department, pictured here in April 2008.
|Manufacturer||Ford Motor Company|
|Also called||Ford Crown Victoria P71 (1998-2009)
Ford Crown Victoria P7B (2010-2011)
|Assembly||St. Thomas, Canada|
|Body and chassis|
|Body style||4-door sedan|
|Successor||Ford Police Interceptor Sedan
Ford Police Interceptor Utility
The Ford Crown Victoria Police Interceptor (colloquially referred to simply as the CVPI, P71 or '"Crown Vic"') is a civilian police car that was manufactured by the Ford Motor Company from 1992 to 2011. It is the law enforcement version of the Ford Crown Victoria. From 1997 and into the early 2010s, the Ford Crown Victoria Police Interceptor was the most widely used automobile in law enforcement operations in the United States and Canada.
- 1 History
- 2 First generation (1992-1997)
- 3 Second generation (1998-2011)
- 4 Comparison with the Crown Victoria
- 5 Identification
- 6 Problems and criticism
- 7 Discontinuation and future
- 8 In popular culture
- 9 References
- 10 Further reading
- 11 External links
After the discontinuation of the Chevrolet Caprice, the Ford Motor Company held a near-monopoly on the market for police cruisers in the United States and Canada for over a decade, because the conventional rear-wheel drive, V8 power, and body-on-frame construction are advantageous for police use. The CVPI's body-on-frame construction allowed inexpensive repairs after collisions without the need to straighten the chassis. Rear-wheel drive made the car easier to avoid spin-outs during hard maneuvers than front drive rivals, and allowed it to better withstand rough driving over curbs and other obstacles in the urban environment.
Although the Ford Crown Victoria Police Interceptor was not sold to the general public, they are widely available via secondhand in North America once they are decommissioned and no longer in service in law enforcement and fleet duty. The cars are in demand by taxi companies, those who want a safe car, and those who need a car with a bench seat which can take three passengers in the back. The Crown Victoria Police Interceptor came equipped with many heavy duty parts such as a revised transmission, and a 187 kW (254 PS; 251 hp) engine. Used Crown Victoria Police Interceptor are normally stripped of any police decals, computer equipment, police radios, and emergency lights before being sold or auctioned to the public.
In April 2011, the Ford Motor Company stopped accepting new orders for the CVPI, instead offering a version of the Ford Taurus. On September 15, 2011, The last Crown Victoria rolled out of the Saint Thomas Assembly Plant and manufacturing of the Ford Crown Victoria stopped altogether. In 2012 a 3rd generation of interceptors started to be made. A Ford Taurus will take the place of the Crown Victoria.
First generation (1992-1997)
A first generation Ford Crown Victoria Police Interceptor of the Miami-Dade Police Department, pictured here in August 2004.
|Body and chassis|
|Related||Mercury Grand Marquis
Lincoln Town Car
|Engine||4.6 L Modular V8|
|Transmission||4-speed AOD/AOD-E automatic
4-speed 4R70W automatic
|Wheelbase||114.4 in (2,906 mm)|
|Length||1992–1994: 212.4 in (5,395 mm)
1995–97: 212.0 in (5,385 mm)
|Width||77.8 in (1,976 mm)|
|Height||1992–1994: 56.7 in (1,440 mm)
1995–97: 56.8 in (1,443 mm)
Though the name has been officially in use since 1992, the 1979–1991 full-size LTDs and LTD Crown Victorias and 1992 updated body style used the "P72" production code designation for both fleet and taxi and police models, with the model itself being internally classified as S (similar to LX). From 1993 to 1997, the police car models of the Crown Victoria were officially known as Crown Victoria P71s.
In the 1993 model year, the Crown Victoria was given a chrome front grille and a reflector strip between the taillights. Another minor restyle followed suit in 1995, with a new grille and taillights. To accommodate the design of the 1995's new taillights, the rear license plate was moved from the bumper to the trunk's lid.
1995–1997 CVPI of the Raleigh, North Carolina, Police Department.
Second generation (1998-2011)
A second generation Ford Crown Victoria Police Interceptor of the Puerto Rico Commonwealth Police, pictured here in May 2010.
|Body and chassis|
|Related||Mercury Grand Marquis
Lincoln Town Car
|Engine||4.6 L Modular V8|
|Transmission||4-speed 4R75W automatic|
|Wheelbase||114.7 in (2,913 mm)|
|Length||212.0 in (5,385 mm)|
|Width||2007: 77.3 in (1,963 mm)
1998–2006: 78.2 in (1,986 mm)
|Height||1998–2001, 2006–2011: 56.8 in (1,443 mm)
2002–05: 58.3 in (1,481 mm)
For the 1998 model year, the Ford Motor Company restyled the Crown Victoria, eliminating the "aero" look that the first generation Crown Victoria had from 1992 to 1997; adopting the more conservative styling of the Mercury Grand Marquis. Both cars included restyled front and rear end components. The 1998 police package P71 had a chrome grille, chrome door handle trim, chrome bumper strips, and a chrome-trimmed flat black rear fascia with the "Crown Victoria" badge. At this time, the car was still known as the "Crown Victoria P71".
1999 introduced the "Crown Victoria Police Interceptor" name, with a badge on the trunk lid replacing the 1998 "Crown Victoria" badge. A chrome-trimmed gloss black rear fascia, unpainted door handle trim, black bumper strips, and a gloss black slatted grille were also introduced at this time. Finally, the new "Street Appearance Package", intended to make the Police Interceptor look like a Standard (P73) model, including chrome trimming and badging, was introduced.
Midway through 1999, the taillights were also changed. 1998 and early 1999 models had a separate amber turn signal along the bottom edge of each taillight housing. Starting in mid-1999, the extra bulbs were eliminated and the turn signals returned to the combination of stop/turn setup with red lenses found in many North American cars. Although the lenses changed, the housings did not; they still had the chambers for the separate turn signals that early models had. These chambers were now empty, leaving a perfect place to install in police cars strobe tubes that would not affect brake or turn signal visibility. Non-Police Interceptors and Police Interceptors equipped with the "Street Appearance Package" retained the amber turn signal.
For 2000, the rear fascia and tail-lights lost the chrome trim, and the gloss black grille was dropped in favor of a flat black slatted grille. Further alterations were made in 2001, including removal of all trim on the plastic bumper pieces and a new honeycomb-style grille, replacing the slat-style grille as is found on previous standard Crown Victorias and CVPIs. Power adjustable pedals also became an option starting in the 2001 model year, as height diversity among officers joining police departments increased. Ford also relocated the rear window defrost switch from the left side of the dash to the direct left of the HVAC controls.
The year 2003 brought a minor redesign. The interior door panels and seats were freshened, with side-impact airbags becoming an option. The 2001–2004 CVPIs all look the same on the exterior; the way for one to tell the 2003 - 2011 cars apart from the 2001 and 2002 models is by examining the wheels. The suspension, brakes, steering, and frame all were redesigned for the 2003 model year. Because of the new underpinnings, the wheels for the newer cars have a much higher offset. They look almost flat, compared to the concave wheels on the older model years. Along with a new wheel design, new hubcaps were introduced.
The 2004–2011 Police Interceptor is rated for 186.5 kW (254 PS; 250 hp) mostly due to the addition of a new better flowing air intake system. This system includes a new airbox that is similar to the Mercury Marauder airbox (raised airbox lid, deeper bottom), with an integrated 80 mm (3.1 in) mass airflow (MAF) sensor that is part of the airbox lid (but can be serviced individually). This allows for much more precise flow calibration and reduces the chances of air leakage. The P71 zip tube (the flexible rubber hose between the throttle body and MAF outlet) is also used to reduce NVH (noise, vibration, and harshness) as well as transfer air from the airbox to the throttle body with minimal flow resistance. From 2005 - on the throttle body is no longer manually operated via cable but an electronic Drive-By-Wire (DBW) set up.
Standard on the 2006 is a redesigned instrument cluster, which now sports an analog speedometer, tachometer, digital odometer with hour meter and trip meter features, and cross-compatibility with the civilian version's various features (these are normally locked out, but can be accessed through wiring modification). Kevlar-lined front doors, which might be useful as protective barriers during gunfights, are optional on the Crown Victoria Police Interceptors for the 2006 Model Year. Also introduced in 2006, for P70/P72 Commercial Heavy Duty models and P71 Police Interceptor models is a 17" steel wheel, replacing the previous 16" wheels, plus new flat gray wheel covers rather than chromed wheel covers as in previous years.
For 2008, the Crown Victoria is restricted to fleet-only sales, and all Panther-platform cars are now flex-fuel cars. The CVPI receives some new options, such as the ability to have keyless entry. Presumably, this feature was added because the Chevrolet Impala Police Sedan has had keyless entry as an option since its inception.
For the 2009 model year, the CVPI now has power pedals as standard equipment. Standard equipment across the entire Panther line is side impact airbags and new federally mandated recessed window switches. The CVPI also received upgraded brakes for 2009, although specifics about them are not available. The confirmation flash that occurs when the doors are locked is now automatically disabled when the Courtesy Lamp Disable option is ordered. The confirmation flash was considered to be a safety issue because the lights would flash when officers exited the vehicle and locked the doors, potentially giving their presence away at night. The car gets the door moldings there were previously available on the civilian P73, P74, & Street Appearance Package variants replacing the door moldings that first appeared on the Police Interceptor & commercial/taxi models in 1998, and also new for 2009 Ford put a "Flex Fuel" badge in the right rear corner of the rear facia (2009 - 2011). The Street Appearance Package also gets the same new door moldings as found on the civilian fleet only Crown Victoria LX as well as blacked rear fascia like the normal Police Interceptor & Crown Victoria LX.
In 2010, the vin code "P71" was replaced with "P7B".
The 2011 model year Ford CVPI (P70, & P72 taxi/commercial and regular civilian model the P74.) received updated larger front headrests to comply with new front crash rating standards.
Palm Beach Police
Comparison with the Crown Victoria
There are few notable differences between the Police Interceptor and standard Crown Victoria or Grand Marquis. Both cars use the same Flex Fuel 4.6 L 2V SOHC V8, Ford Modular engine, and Ford 4-speed automatic transmission.
Engine and drive train
The Police Interceptor is equipped with an external oil-to-engine-coolant oil cooler to reduce engine oil temperatures, allowing the vehicles to operate at high rpm/high loads for an extended period of time without the risk of engine oil overheating and subsequent engine damage. This engine oil cooler can be prone to seeping oil from the O-ring seals after the high mileage operation encountered by Police Interceptors, particularly where damaged by road salt.
The Police Interceptor engine calibration includes a slightly higher idle speed (by approximately 40 rpm) and minor changes in the emissions settings. The computer is tuned for more aggressive transmission shift points, and the transmission itself is built for firmer and harder shifts. The engine has slightly higher compression over the stock 4.6L used in non-police vehicles, at 9.6:1 vs 9.5:1. The EGR system is controlled differently on 03+ vehicles than on 03+ non-police vehicles.
The 2006–present Police Interceptors are mostly equipped with a 3.27:1 rear axle ratio (Axle code Z5) and are electronically limited to 140 mph (225 km/h) due to critical driveline speed limitations. (The weight of the vehicle with law-enforcement equipment on-board makes it highly unlikely the vehicle could ever reach speeds approaching this figure. However, a flat-out figure of 125 mph is the best that could be expected with the 4.6 modular V8, unless driving on an open straight for an extended period of time.). An optional 3.55:1 trac loc rear axle ratio with 120 mph speed limiter was available (Axle code X5 or C6). Pre-2006 Police Interceptors equipped with the 3.27:1 rear axle ratio were generally limited to approximately 131 mph (211 km/h). This is compares to the standard non-P71 2.73 rear axle ratio with a speed limitation of 110 mph (177 km/h) for all "civilian" Crown Victorias.
Ford used an aluminum metal matrix composite driveshaft for the 1993–2005 Police Interceptors as a measure to allow safe operation at over 150 mph (241 km/h), but it was more expensive than the regular aluminum driveshafts. Ford reintroduced a 3.55:1 rear axle ratio for the 2006 model year Police Interceptors with a 120 mph (193 km/h) speed limitation to reduce the risk of driveshaft failure.
Police Interceptors also have a reinforced frame and body mounts and an optional limited slip rear differential.
Body and chassis
Another difference is Ford's "severe duty" shock absorbers that offer a stiffer ride than the standard Crown Victoria. They also have black steel wheels with stainless steel or chromed plastic hubcaps.
All Police Interceptors also come with T-409 stainless steel dual exhaust systems without resonators. Standard Crown Victorias come with a stainless steel single exhaust system, while the Handling and Performance Package and LX Sport-equipped Crown Victorias have the same exhaust system as the Police Interceptor, with the resonators. The resonators further reduce noise, vibration, and harshness without adding any restriction to the exhaust system. Police Interceptors have higher-rate coil springs, approximately 0.8 inches (20.3 mm) of additional ground clearance, and thinner rear antiroll bars (shared with the LX Sport) than the Handling and Performance Package Crown Victorias; the base Crown Victoria does not have a rear antiroll bar.
Ford also offers trunk packages for equipment storage (see below), and as of 2005, has added an optional fire suppression system to the Police Interceptor.
The bulk of police car modifications, such as installation of emergency lights, sirens, passenger seat dividers, and plastic rear bench seats, are offered as aftermarket modifications by third parties.
Most Police Interceptors have a break in the front "bench seat" despite having the shifter on the steering column. This gap between seats is generally filled by a console holding radios, controls for emergency equipment, large firearms, and often a laptop computer or mobile data terminal (MDT). The Police Interceptor also has a calibrated 140 mph (225 km/h) speedometer.
One way to distinguish most P71s is the small "Police Interceptor" badge that replaces the standard "Crown Victoria" markings on the trunk lid, although the Street Appearance Package (SAP) Police Interceptors forgo this badge, using the standard Crown Victoria marking. Police Interceptor badges are now available for purchase online, so this identifying technique is not as reliable as it once was. Street Appearance Package (SAP) cars also use chrome trim rather than the black trim of normal Police Interceptors. P71s can also be identified by the dual exhaust and an analog 140 mph speedometer. The Police Interceptor has the interior trunk release in the center of the dashboard with a prominent warning decal right below it, while the civilian version has it in the driver's door. All 1998 and newer Crown Victorias made for civilian (non-fleet) use have a five digit horizontal keypad (known as SecuriCode) above the driver side door handle which can be used to lock/unlock the car and open its trunk. All P70, 71, and 72 Crown Victorias are assembled without this keyless entry system so unless the driver door was damaged and had an improper replacement door installed any Crown Victoria you see with a keypad is a civilian one, while any one without a keypad is a P70, 71, or 72 fleet Crown Victoria. The only completely infallible way to identify a Police Interceptor is to look for the code "P71" in the VIN, or "P7B", as it was renamed in 2010.
Police Interceptors will have the characters "P71" as the model code in the VIN, or "P7B" for 2010+ models, instead of P70 (Stretched wheelbase), P72 (Commercial Heavy Duty/Taxi and fleet vehicles), P73 (Base), P74 (LX), or P75 (1992 Touring Sedan).
Only Police Interceptors were available with black front grilles.
Problems and criticism
|This section does not cite any references or sources. (August 2010)|
Following the criticism of fires following highway-speed rear-end collisions, 2005 and later model Police Interceptors now come with an optional automatic fire suppression system and special "trunk packs" designed to prevent cargo from penetrating the fuel tank in a collision. The customer must pay an additional $150 per car for the trunk packs. For a more detailed discussion of the fuel tank leakage concerns that prompted these changes, see Ford Crown Victoria.
There were also some problems with early 2003 Police Interceptors. The newly designed steel wheels would rust prematurely, and the rack and pinion steering units would fail early (≤10,000 miles). This was not limited to the Police Interceptor; some 2004 Mercury Marauders were also affected. A recent recall (04M05) affects the steel wheels used on 2003–05 Police Interceptors.[verification needed]
Another issue with the wheels have been weld points that come loose, causing rapid air loss in tires and the potential for loss of control. A recall was issued after an investigation by the National Highway Traffic Safety Administration. However, the company has created anger among civilian owners of 2003+ Police Interceptors by refusing to honor the recall unless the vehicle is still being used in fleet service. The only way this problem could be addressed is if the civilian customer complains to a dealership about air leakage problems, an inability to balance the wheels properly, or a "nibble" or excessive vibration in the steering at speed. The issue is then addressed through the "Customer Satisfaction Program" that Ford has initiated for the same wheels. Ford ultimately resolved this issue on production cars in 2006 by introducing new 17" steel wheels for their heavy duty models. These wheels may be of interest to those who have 2003–2005 Police Interceptors, 2003–2005 P70/P72 Commercial Heavy Duty models or 2003–2008 Standard (P73) models with 16" steel wheels and are concerned about the safety of these wheels.
The steel body-on-frame Crown Victoria Police Interceptor fares better in crashes than current unibody counterparts such as the Chevrolet Impala and Dodge Charger. Collision damage is also repaired more economically. Many law enforcement officers and departments swear by the proven Crown Victoria, and are reluctant to purchase other police sedans in spite of the Crown Vic's departure. Some departments have purchased the Chevrolet Tahoe 9C1, a full-size SUV, due in part to its body-on-frame construction.
Discontinuation and future
On March 12, 2010, Ford Motor Company introduced the 2013 Police Interceptor as a rebadged and reengineered version of the current Taurus. This new vehicle is on an all-wheel drive unibody platform (with optional front-wheel drive), and it bears no relation to the rear-wheel body-on-frame Panther platform that underpinned all previous Police Interceptors.
In response, police departments like that of Austin, Texas, are buying reserve supplies of the last Crown Victorias to allow them to maintain a fleet of reliable police cars into the future. The police department in London, Ontario which had been stockpiling extra CVPI's noted that while potential replacements may use less gasoline, the CVPI may be easily and cheaply converted to run on propane, giving it lower running costs than its competitors and the Taurus that Ford is touting as a replacement. Others have reluctantly shifted to other models and manufacturers.
On September 15, 2011, the final built Crown Victoria, a civilian model destined for Saudi Arabia, rolled off the assembly line at 12:30 PM, concluding assembly operations of the St. Thomas, Ontario plant.
In popular culture
As a consequence of its popularity from the 1996 discontinuation of the Chevrolet Caprice 9C1 which later return in 2011 based on Holden's Caprice from the WM/WN range imported from Australia as the Caprice PPV, the Ford Crown Victoria Police Interceptor is one of the most common police vehicles depicted in contemporary North American films, television, and video game franchises. The Crown Victoria is seen extensively in popular culture as the main police vehicle of the United States, but in following with real-life police departments, crime dramas (such as Hawaii Five-0) are now using replacements such as the, Chevrolet Impala 9C1/9C3, Dodge Charger, and Ford Police Interceptor Sedan.
- "Ford to retire Crown Vics; police cars to get makeover". StarNewsOnline.com. Retrieved 2011-04-24.
- "Article Archive - Law and Order, Police Fleet Manager, Tactical Response, Public Safety IT | Hendon Publishing". Hendonpub.com. 2001-09-11. Retrieved 2013-10-09.
- "Police Interceptor Information". p71owners.com.
- Gratson, Tony (July 2008). "Ford CVPI extended through 2011". Police Fleet Manager Magazine.
- "Police Interceptor Oil Cooler Information". p71interceptor.com.
- Hagin, Matt/Bob. "FORD CROWN VICTORIA LX (1999)". The Auto Channel.
- "The New Ford Police Interceptor (Formerly the CVPI / P71) Law Enforcement Vehicle". Ford.
- "Austin police ask for $4.5 million to stock up on Crown Victorias". Statesman.com. Retrieved 2011-04-24.
- Gurliacci, David (2011-03-31). "Norwalk Police Buying Eight of the Final Batch of Crown Victoria Patrol Cars – Norwalk, CT Patch". Norwalk.patch.com. Retrieved 2011-04-24.
- Sher, Jonathan (2010-09-09). "Stockpiled Crown Vics defended | London | News | London Free Press". Lfpress.com. Retrieved 2011-04-24.
- David, Brennan (2011-04-16). "Police switching to Tahoe SUV | The Columbia Daily Tribune – Columbia, Missouri". Columbiatribune.com. Retrieved 2011-04-24.
- "The Last Crown Vic Rolls (but Not as a New York Cab)". nytimes.com. 2011-09-15. Retrieved 2011-09-16.
- Sanow, Edwin J (1997), Ford Police Cars, 1932-1997, Motorbooks International Publishers, ISBN 0-7603-0372-X
|Wikimedia Commons has media related to Ford Crown Victoria Police Interceptor.|
- Ford Crown Victoria (U.S.A.): Police Interceptor | Commercial Version (includes long-wheelbase version)
- Crown North America – Ford's Tier One Supplier of Factory Installed Police Prep Pkgs & Ballistic Door Panels: Crown North America