Electric field

From Wikipedia, the free encyclopedia
  (Redirected from E-field)
Jump to: navigation, search
Electric field lines emanating from a point positive electric charge suspended over an infinite sheet of conducting material.

The electric field is a component of the Electromagnetic field. It is a vector field, and it is generated by electric charges or time-varying magnetic fields as described by Maxwell's equations.

The concept of an electric field was introduced by Michael Faraday[citation needed].

Definition[edit]

The electric field \mathbf{E} at a given point is defined as the (vectorial) force \mathbf{F} that would be exerted on a stationary test particle of unit charge by electromagnetic forces (i.e. the Lorentz force). A particle of charge q would be subject to a force \mathbf{F}=q.\mathbf{E}.

Its SI units are newtons per coulomb (N⋅C−1) or, equivalently, volts per metre (V⋅m−1), which in terms of SI base units are kg⋅m⋅s−3⋅A−1.

Sources of electric field[edit]

Causes and description[edit]

Electric fields are caused by electric charges or varying magnetic fields. The former effect is described by Gauss's law, the latter by Faraday's law of induction, which together are enough to define the behavior of the electric field as a function of charge repartition and magnetic field. However, since the magnetic field is described as a function of electric field, the equations of both fields are coupled and together form Maxwell's equations that describe both fields as a function of charges and currents.

In the special case of a steady state (stationary charges and currents), the Maxwell-Faraday inductive effect disappears. The resulting two equations (Gauss's law \nabla \cdot \mathbf{E} = \frac{\rho}{\varepsilon_0} and Faraday's law with no induction term \nabla \times \mathbf{E} = 0), taken together, are equivalent to Coulomb's law, written as \boldsymbol{E}(\boldsymbol{r}) = {1\over 4\pi\varepsilon_0}\int d\boldsymbol{r'} \rho(\boldsymbol{r'}) {\boldsymbol{r} - \boldsymbol{r'} \over |\boldsymbol{r} - \boldsymbol{r'}|^3} for a charge density \mathbf{\rho}(\mathbf{r}) (\mathbf{r} denotes the position in space). Notice that \varepsilon_0, the permittivity of vacuum, must be susbstituted if charges are considered in non-empty medium.

Continuous vs. discrete charge repartition[edit]

Main article: Charge density

The equations of electromagnetism are best described in a continuous description. However, charges are sometimes best described as discrete points; for example, some models may describe electrons as punctual sources where charge density is infinite on an infinitesimal section of space.

A charge q located in \mathbf{r_0} can be described mathematically as a charge density \rho(\mathbf{r})=q\delta(\mathbf{r-r_0}), where the Dirac delta function (in three dimensions) is used. Conversely, a charge distribution can be approximated by many small punctual charges.

Superposition principle[edit]

Electric fields satisfy the superposition principle, because Maxwell's equations are linear. As a result, if \mathbf{E}_1 and \mathbf{E}_2 are the electric fields resulting from distribution of charges \rho_1 and \rho_2, a distribution of charges \rho_1+\rho_2 will create an electric field \mathbf{E}_1+\mathbf{E}_2; for instance, Coulomb's law is linear in charge density as well.

This principle is useful to calculate the field created by multiple point charges. If charges q_1, q2,...q_n are stationary in space at \mathbf{r}_1,\mathbf{r}_2,...\mathbf{r}_n, in the absence of currents, the superposition principle prove that the resulting field is the sum of fields generated by each particle as described by Coulomb's law:

\mathbf{E}(\mathbf{r}) = \sum_{i=1}^N \mathbf{E}_i(\mathbf{r}) =
\frac{1}{4\pi\varepsilon_0} \sum_{i=1}^N q_i \frac{\mathbf{r}-\mathbf{r}_i}{|\mathbf{r}-\mathbf{r}_i|^3}

Electrostatic fields[edit]

Main article: Electrostatics
Illustration of the electric field surrounding a positive (red) and a negative (blue) charge.
Electric field between two conductors

Electrostatic fields are E-fields which do not change with time, which happens when charges and currents are stationary. In that case, Coulomb's law fully describes the field.

Electric potential[edit]

By Faraday's law, the electric field has zero curl. One can then define an electric potential, that is, a function \Phi such that  \mathbf{E} = -\nabla \Phi .[1] This is analogous to the gravitational potential.

Parallels between electrostatic and gravitational fields[edit]

Coulomb's law, which describes the interaction of electric charges:


\mathbf{F}=q\left(\frac{Q}{4\pi\varepsilon_0}\frac{\mathbf{\hat{r}}}{|\mathbf{r}|^2}\right)=q\mathbf{E}

is similar to Newton's law of universal gravitation:


\mathbf{F}=m\left(-GM\frac{\mathbf{\hat{r}}}{|\mathbf{r}|^2}\right)=m\mathbf{g}

(where \mathbf{\hat{r}}=\mathbf{\frac{r}{|r|}}).

This suggests similarities between the electric field E and the gravitational field g, or their associated potentials. Mass is sometimes called "gravitational charge" beause of that similarity.[citation needed]

Electrostatic and gravitational forces both are central, conservative and obey an inverse-square law.

Uniform fields[edit]

A uniform field is one in which the electric field is constant at every point. It can be approximated by placing two conducting plates parallel to each other and maintaining a voltage (potential difference) between them; it is only an approximation because of boundary effects (near the edge of the planes, electric field is distorted because the plane does not continue). Assuming infinite planes, the magnitude of the electric field E is:

 E = - \frac{\Delta\phi}{d}

where Δϕ is the potential difference between the plates and d is the distance separating the plates. The negative sign arises as positive charges repel, so a positive charge will experience a force away from the positively charged plate, in the opposite direction to that in which the voltage increases. In micro- and nanoapplications, for instance in relation to semiconductors, a typical magnitude of an electric field is in the order of 10^6\ V.m^{-1}, achieved by applying a voltage of the order of 1 volt between conductors spaced 1 µm apart.

Electrodynamic fields[edit]

Main article: Electrodynamics

Electrodynamic fields are E-fields which do change with time, for instance when charges are in motion.

The electric field cannot be described independently of the magnetic field in that case. If A is the magnetic vector potential, defined so that  \mathbf{B} = - \nabla \times \mathbf{A} , one can still define an electric potential  \Phi such that:

 \mathbf{E} = - \nabla \Phi - \frac { \partial \mathbf{A} } { \partial t }

One can recover Faraday's law of induction by taking the curl of that equation

[2]
\nabla \times \mathbf{E} = -\frac{\partial (\nabla \times \mathbf{A})} {\partial t}=
-\frac{\partial \mathbf{B}} {\partial t}

which justifies, a posteriori, the previous form for E.

Energy in the electric field[edit]

If the magnetic field B is nonzero,

The total energy per unit volume stored by the electromagnetic field is[3]

 u_{EM} = \frac{\varepsilon}{2}  |\mathbf{E}|^2 + \frac{1}{2\mu} |\mathbf{E}|^2

where ε is the permittivity of the medium in which the field exists, \mu its magnetic permeability, and E and B are the electric and magnetic field vectors.

As E and B fields are coupled, it would be misleading to split this expression into "electric" and "magnetic" contributions. However, in the steady-state case, the fields are no longer coupled (see Maxwell's equations). It makes sense in that case to compute the electrostatic energy per unit volume:

 u_{ES} = \frac{1}{2} \varepsilon |\mathbf{E}|^2 \, ,

The total energy U stored in the electric field in a given volume V is therefore

 U_{ES} = \frac{1}{2} \varepsilon \int_{V} |\mathbf{E}|^2 \, \mathrm{d}V \, ,

Further extensions[edit]

Definitive equation of vector fields[edit]

In the presence of matter, it is helpful in electromagnetism to extend the notion of the electric field into three vector fields, rather than just one:[4]

\mathbf{D}=\varepsilon_0\mathbf{E}+\mathbf{P}\!

where P is the electric polarization – the volume density of electric dipole moments, and D is the electric displacement field. Since E and P are defined separately, this equation can be used to define D. The physical interpretation of D is not as clear as E (effectively the field applied to the material) or P (induced field due to the dipoles in the material), but still serves as a convenient mathematical simplification, since Maxwell's equations can be simplified in terms of free charges and currents.

Constitutive relation[edit]

Main article: Constitutive equation

The E and D fields are related by the permittivity of the material, ε.[5][6]

For linear, homogeneous, isotropic materials E and D are proportional and constant throughout the region, there is no position dependence: For inhomogeneous materials, there is a position dependence throughout the material:

\mathbf{D(r)}=\varepsilon\mathbf{E(r)}

For anisotropic materials the E and D fields are not parallel, and so E and D are related by the permittivity tensor (a 2nd order tensor field), in component form:

D_i=\varepsilon_{ij}E_j

For non-linear media, E and D are not proportional. Materials can have varying extents of linearity, homogeneity and isotropy.

See also[edit]

References[edit]

  1. ^ http://physicspages.com/2011/10/08/curl-potential-in-electrostatics/
  2. ^ Huray, Paul G. (2009). Maxwell's Equations. Wiley-IEEE. p. 205. ISBN 0-470-54276-4. 
  3. ^ Introduction to Electrodynamics (3rd Edition), D.J. Griffiths, Pearson Education, Dorling Kindersley, 2007, ISBN 81-7758-293-3
  4. ^ Electromagnetism (2nd Edition), I.S. Grant, W.R. Phillips, Manchester Physics, John Wiley & Sons, 2008, ISBN 978-0-471-92712-9
  5. ^ Electricity and Modern Physics (2nd Edition), G.A.G. Bennet, Edward Arnold (UK), 1974, ISBN 0-7131-2459-8
  6. ^ Electromagnetism (2nd Edition), I.S. Grant, W.R. Phillips, Manchester Physics, John Wiley & Sons, 2008, ISBN 978-0-471-92712-9

External links[edit]