# Statcoulomb

(Redirected from Electrostatic unit)

The statcoulomb (statC) or franklin (Fr) or electrostatic unit of charge (esu) is the physical unit for electrical charge used in the centimetre–gram–second system of units (cgs) and Gaussian units. It is a derived unit given by

1 statC = 1 g1/2 cm3/2 s−1 = 1 erg1/2 cm1/2.

The SI system of units uses the coulomb (C) instead. The conversion between C and statC is different in different contexts. The most common contexts are:

1 C ↔ 2997924580 statC ≈ 3.00×109 statC (for electric charge)
1 statC ↔ ≈3.33564×10−10 C (for electric charge).
1 C ↔ 4π×2997924580 statC ≈3.77×1010 statC (for electric flux ΦD)
1 statC ↔ ≈2.65×10−11 C (for electric flux ΦD).
1 C/m2 ↔ 4π×2997924580×10−4 statC/cm23.77×106 statC/cm2 (for electric displacement field D)
1 statC/cm2 ↔ ≈2.65×10−7 C/m2 (for electric displacement field D).

The symbol "↔" is used instead of "=" because the two sides are not necessarily interchangeable, as discussed below. The number 2997924580 is 10 times the value of the speed of light expressed in meters/second, and the conversions are exact except where indicated.

The coulomb is an extremely large charge rarely encountered in electrostatics, while the statcoulomb is closer to everyday charges.

## Definition and relation to cgs base units

The statcoulomb is defined as follows: if two stationary objects each carry a charge of 1 statC and are 1 cm apart, they will electrically repel each other with a force of 1 dyne. This repulsion is governed by Coulomb's law, which in the Gaussian-cgs system states:

$F=\frac{q_1q_2}{r^2}$

where F is the force, q1 and q2 are the two charges, and r is the distance between the charges. Performing dimensional analysis on Coulomb's law, the dimension of electrical charge in cgs must be [mass]1/2 [length]3/2 [time]−1. (This statement is not true in SI units; see below.) We can be more specific in light of the definition above: Plugging in F = 1 dyne, q1 = q2 = 1 statC, and r = 1 cm, we get:

1 statC = g1/2 cm3/2 s−1

as expected.

## Dimensional relation between Statcoulomb and Coulomb

### General incompatibility

Coulomb's law in cgs-Gaussian unit system and SI are respectively:

$F=\frac{q_1q_2}{r^2}$ (cgs-Gaussian)
$F=\frac{q_1q_2}{4\pi\epsilon_0 r^2}$ (SI)

Since ε0, the vacuum permittivity, is not dimensionless, the coulomb (the SI unit of charge) is not dimensionally equivalent to [mass]1/2 [length]3/2 [time]−1, unlike the statcoulomb. In fact, it is impossible to express the coulomb in terms of mass, length, and time alone.

Consequently, a conversion equation like "1 C = N statC" can be misleading: the units on the two sides are not consistent. One cannot freely switch between coulombs and statcoulombs within a formula or equation, as one would freely switch between centimeters and meters. One can, however, find a correspondence between coulombs and statcoulombs in different contexts. As described below, "1 C corresponds to 3.00×109 statC" when describing the charge of objects. In other words, if a physical object has a charge of 1 C, it also has a charge of 3.00×109 statC. Likewise, "1 C corresponds to 3.77×1010 statC" when describing an electric displacement field flux.

### As a unit of charge

The statcoulomb is defined as follows: If two stationary objects each carry a charge of 1 statC and are 1 cm apart, they will electrically repel each other with a force of 1 dyne. From this definition, it is straightforward to find an equivalent charge in SI coulombs. Using the SI equation

$F=\frac{q_1q_2}{4\pi\epsilon_0 r^2}$ (SI),

and plugging in F = 1 dyne = 10−5 N, and r = 1 cm = 10−2 m, and then solving for q = q1 = q2, the result is q = (1/2997924580)C ≈ 3.34×10−10 C. Therefore an object with a charge of 1 statC has a charge of 3.34×10−10 C.

This can also be expressed by the following conversion, which is fully dimensionally consistent, and often useful for switching between SI and cgs formulae:

$1 \; \mathrm{C}/\sqrt{4 \pi \epsilon_0} = 2997924580 \; \mathrm{statC}$

### As a unit of electric displacement field or flux

An electric flux (specifically, a flux of the electric displacement field D) has units of charge: statC in cgs and coulombs in SI. The conversion factor can be derived from Gauss's law:

$\Phi_D = 4\pi Q$ (cgs)
$\Phi_D = Q$ (SI)

where

$\Phi_D \equiv \int_S \mathbf{D}\cdot \mathrm{d}\mathbf{A}$

Therefore the conversion factor for flux is 4π different than the conversion factor for charge:

$1 \; \mathrm{C} \text{ corresponds to } 3.7673 \times 10^{10} \; \mathrm{statC}$ (as unit of ΦD).

The dimensionally consistent version is:

$1 \; \mathrm{C}\sqrt{4 \pi /\epsilon_0} = 3.7673 \times 10^{10} \; \mathrm{statC}$ (as unit of ΦD).