A flatcar (US) (also flat car (US) or flat wagon (UIC)) is a piece of railroad (US) or railway (non-US) rolling stock that consists of an open, flat deck on four or six wheels or a pair of trucks (US) or bogies (UK). The deck of the car can be wood or steel, and the sides of the deck can include pockets for stakes or tie-down points to secure loads. Flatcars designed for carrying machinery have sliding chain assemblies recessed in the deck.
Flatcars are used for loads that are too large or cumbersome to load in enclosed cars such as boxcars. They are also often used to transport intermodal containers (shipping containers) or trailers as part of intermodal freight transport shipping.
Aircraft parts flatcars
Aircraft parts were hauled via conventional freight cars beginning in World War II. However, given the ever-increasing size of aircraft assemblies, the "Sky Box" method of shipping parts was developed in the late 1960s specifically to transport parts for the Boeing 747 and other "jumbo" jets of the time. The "Sky Box" consists of a two-piece metal shell that is placed atop a standard flatcar to support and protect wing and tail assemblies and fuselage sections in transit (originally, depressed-center or "fish belly" cars were utilized).
Bulkhead flatcars are designed with sturdy end-walls (bulkheads) to prevent loads from shifting past the ends of the car. Loads typically carried are pipe, steel slabs, utility poles and lumber, though lumber and utility poles are increasingly being hauled by skeleton cars. Bulkheads are typically lightweight when empty. An empty bulkhead on a train puts it at a speed restriction to go no more that 50MPH. Since bulkheads are lightweight when empty, hunting can occur when the car is above 50MPH. Hunting is the wobbling movement of the trucks on a freight car or a locomotive and If the wheels hunt against the rails for a period of time, there is a high risk of a derailment.
Centerbeam flatcars/Lumber racks
Centerbeam flatcars, centerbeams, center partition railcars or commonly referred to as lumber racks are specialty cars designed for carrying bundled building supplies such as dimensional lumber, wallboard, and fence posts. They are essentially bulkhead flatcars that have been reinforced by a longitudinal I-beam, often in the form of a Vierendeel truss, sometimes reinforced by diagonal members. They must be loaded symmetrically, with half of the payload on one side of the centerbeam and half on the other to avoid tipping over.
Heavy capacity flatcars
Heavy capacity flatcars are cars designed to carry more than 100 short tons (90.72 t; 89.29 long tons). They often have more than the typical North American standard of four axles (one two axle truck at each end), and may have a depressed center or "fish belly" to handle excess-height loads as well as two trucks of three axles each (one at each end) or four trucks (two at each end) of two axles each, connected by span bolsters. Loads typically handled include electrical power equipment and large industrial production machinery.
A circus train is a modern method of conveyance for circus troupes. One of the larger users of circus trains is the Ringling Bros. and Barnum & Bailey Circus (RBBB), a famous American circus formed when the Ringling Brothers Circus purchased the Barnum and Bailey Circus in 1907.
Remote control use
Some companies, such as CSX Transportation, have former wood-carrying flatcars rebuilt into platforms which mount remote control equipment for use in operating locomotives. Such platforms are fitted with appropriate headlights, horns, and air brake appliances to operate in the leading position on a cut of cars (i.e. coupled ahead of the locomotive).
Intermodal freight use
COFC (container on flat car) cars are typically 89 feet (27 m) long and carry four 20-foot (6.10 m) intermodal containers or two 40-foot (12.19 m)/45-foot (13.72 m) shipping containers (the two 45-foot or 13.72-metre containers are carryable due to the fact that the car is actually 92 ft (28 m) long, using the strike plates). With the rise of intermodal freight transport-specific cars, and given the age of most of these flats, numbers will decline over the next several years. Indeed, when the first well cars appeared, allowing double stacking, many container flats were re-built as autoracks. The few "new build" container flats are identifiable by their lack of decking, welded steel frame, and standard 89-foot (27 m) length. One variant is the 50 feet (15 m) car (which usually carries one large container as a load); these are actually re-built old boxcars. Common reporting marks are FEC, CP, SOO and KTTX. The ATTX cars, which feature no spark grips and sides, are built for hauling dangerous goods (ammunition, flammable fluids, etc.).
A TOFC (trailer on flat car, a.k.a. piggy-back) car once again, is usually an 89 ft (27 m) car. In the past, these carried three 30 ft (9.1 m) trailers which are, as of 2007, almost obsolete, or one large, 53 ft (16 m), two 40-foot (12.19 m) or 45-foot (13.72 m) trailers. As intermodal traffic grows, these dedicated flats are in decline. Most have been modified to also carry containers. One notable type is Canadian Pacific Railway's XTRX service — dedicated five-unit flats that only carry trailers.
Spine cars, trailer on flat car, or piggy back cars allow two 28.5 trailer pups or one trailer up to 57 feet to be carried. They usually come in articulated sets of 5 or 3.
A center sill and side sill only car with lateral arms to support intermodal containers.
Similar to the spine car except that it is designed to carry lumber or utility poles, a skeleton car is composed of a center sill and lateral arms only. No deck, sometimes no side sills and sometimes no end sills.
In marine service, the linkspan between a ferry or barge and its dock is very weak. In order to avoid loss of cargo and/or heavy locomotives, an old flatcar (which is usually the lightest car available) is used as a bridge between the locomotive on the dock and the cars on the ferry or barge.
Idler flatcars are also used in oversize freight service, as loads such as pipe often overhang the ends of most standard-sized flatcars. Empty flatcars will be placed on both ends of the loaded car. This protects the cargo ends from damage and ensures that the loaded cars don't bind, and damage the ends of adjacent cars.
Often a flat car is placed directly in front of a crane ("big hook") in order to:
- provide a way to remove a wrecked car from a crash site.
- provide a way to store new or removed rail from a work site.
- allow room for the crane's boom while in transit to and from a work site.
- Guide to Railcars
- "NP Flat Car Diagrams". Northern Pacific Railway Historical Association. Retrieved November 21, 2012.
- 40 ft (12.19 m) log flat car with side stakes
- 42 ft (12.80 m) log flat car with side stakes
- Skelleton logging car, 80,000 lb (36,000 kg) capacity
- Thompson, Scott R. (1996). Great Northern Equipment Color Pictorial: Book Two, Freight Cars. Four Ways West Publications, La Mirada, CA. ISBN 1-885614-11-X.
|Wikimedia Commons has media related to Flat railway wagons.|