Hidden node problem
In wireless networking, the hidden node problem or hidden terminal problem occurs when a node is visible from a wireless access point (AP), but not from other nodes communicating with that AP. This leads to difficulties in media access control.
Hidden nodes in a wireless network refer to nodes that are out of range of other nodes or a collection of nodes. Take a physical star topology with an access point with many nodes surrounding it in a circular fashion: Each node is within communication range of the AP, but the nodes cannot communicate with each other, as they do not have a physical connection to each other. In a wireless network, it is likely that the node at the far edge of the access point's range, which is known as A, can see the access point, but it is unlikely that the same node can see a node on the opposite end of the access point's range, C. These nodes are known as hidden. The problem is when nodes A and C start to send packets simultaneously to the access point B. Because the nodes A and C are out of range of each other and so cannot detect a collision while transmitting, Carrier sense multiple access with collision detection (CSMA/CD) does not work, and collisions occur, which then corrupt the data received by the access point. To overcome the hidden node problem, RTS/CTS handshaking is implemented in conjunction with the Carrier sense multiple access with collision avoidance (CSMA/CA) scheme. The same problem exists in a MANET.
The hidden node problem can be observed easily in widespread (>50m radius) WLAN setups with many nodes that use directional antennas and have high upload. This is why IEEE 802.11 is suited for bridging the last mile for broadband access only to a very limited extent. Newer standards such as WiMAX assign time slots to individual stations, thus preventing multiple nodes from sending simultaneously and ensuring fairness even in over-subscription scenarios.
IEEE 802.11 uses 802.11 RTS/CTS acknowledgment and handshake packets to partly overcome the hidden node problem. RTS/CTS is not a complete solution and may decrease throughput even further, but adaptive acknowledgments from the base station can help too.
The comparison with hidden stations shows that RTS/CTS packages in each traffic class are profitable (even with short audio frames, which cause a high overhead on RTS/CTS frames). 
In the experimental environment following traffic classes are included: data (not time critical), data (time critical), video, audio. Examples for notations: (0|0|0|2) means 2 audio stations; (1|1|2|0) means 1 data station (not time critical), 1 data station (time critical), 2 video stations.
The other methods that can be employed to solve hidden node problem are :
- Increase Transmitting Power From the Nodes
- Use omnidirectional antennas
- Remove obstacles
- Move the node
- Use protocol enhancement software
- Use antenna diversity
Increasing Transmitting Power From the Nodes
Increasing the transmission power of the nodes can solve the hidden node problem by allowing the cell around each node to increase in size, encompassing all of the other nodes. This configuration enables the non-hidden nodes to detect, or hear, the hidden node. If the non-hidden nodes can hear the hidden node, the hidden node is no longer hidden. Because wireless LANs use the CSMA/CA protocol, nodes will wait their turn before communicating with the access point.
Since nodes using directional antennas are nearly invisible to nodes that are not positioned in the direction the antenna is aimed at, directional antennas should be used only for very small networks (e.g., dedicated point-to-point connections). Use omnidirectional antennas for widespread networks consisting of more than two nodes.
Increasing the power on mobile nodes may not work if, for example, the reason one node is hidden is that there is a cement or steel wall preventing communication with other nodes. It is doubtful that one would be able to remove such an obstacle, but removal of the obstacle is another method of remedy for the hidden node problem. Keep these types of obstacles in mind when performing a site survey.
Moving the node
Another method of solving the hidden node problem is moving the nodes so that they can all hear each other. If it is found that the hidden node problem is the result of a user moving his computer to an area that is hidden from the other wireless nodes, it may be necessary to have that user move again. The alternative to forcing users to move is extending the wireless LAN to add proper coverage to the hidden area, perhaps using additional access points.
Equalizing technology, which is fully compatible with 802.11, works by taking advantage of the natural inclination of Internet connections to back off when artificially restrained.
Equalizing periodically (every second) measures the total aggregate bandwidth throughput traversing the AP. If it is sensed that the upper limit is being reached, the dominating flows will be identified and encouraged to back off by artificially restraining them. This frees up bandwidth for lesser powered remote nodes.
By keeping track of every flow going through the AP, equalizing technology can identify those taking an unequal share of bandwidth and thus crowding out flows from weaker nodes.
Equalizing discriminates detrimental flows by taking the following questions into consideration:
- How persistent is the flow?
- How many active flows are there?
- How long has the flow been active?
- How much total congestion is currently on the trunk?
- How much bandwidth is the flow using relative to the link size?
The key to making this happen over 802.11 relies on the fact that if you slow a stream down, the application at the root cause will back off and also slow down. This can be done by the deploying equalzing technology after the access point without any changes to the 802.11 protocol since the throttling is actually done independent of the radio. The throttling of heavy streams happens between the AP and the connection to the Internet (or other external source).
Traffic equalizing technologies are not universally applicable solutions to the hidden node problem. Rather, they are primarily a pragmatic fix to reduce symptoms without fixing the underlying problem.
Protocol enhancement software
There are several software implementations of additional protocols that essentially implement a polling or token passing strategy. Then, a master (typically the access point) dynamically polls clients for data. Clients are not allowed to send data without the master's invitation. This eliminates the hidden node problem at the cost of increased latency and less maximum throughput.