Humbucker

From Wikipedia, the free encyclopedia
  (Redirected from Humbucking pickup)
Jump to: navigation, search
"Open Coil" (uncovered) humbucker pickup
Covered humbucker pickup on a Les Paul

A humbucking pickup, or humbucker is a type of electric guitar pickup that uses two coils to "buck the hum" (or cancel out the interference) picked up by coil pickups. Most pickups use magnets to produce a magnetic field around the strings, and induce an electrical current in the coils as the strings vibrate (a notable exception is the piezoelectric pickup). Humbuckers work by pairing a coil with the north poles of its magnets oriented "up", (toward the strings) with a coil which has the south pole of its magnets oriented up. By connecting the coils together out of phase, the interference is significantly reduced via phase cancellation. The coils can be connected in series or in parallel. In addition to electric guitar pickups, humbucking coils are sometimes used to cancel hum in dynamic microphones.

Hum is caused by the alternating magnetic fields created by transformers and power supplies inside electrical equipment using alternating current. While playing a guitar without humbuckers, a musician would hear a hum through his pickups during quiet sections of music. Sources of studio and stage hum include high-power amps, processors, mixers, motors, power lines, and other equipment. Compared to unshielded single coil pickups, humbuckers dramatically reduce hum.

History[edit]

The "humbucking coil" was invented in 1934 by Electro-Voice, an American professional audio company based in South Bend, Indiana that Al Kahn and Lou Burroughs incorporated in 1930 for the purpose of manufacturing portable public address equipment, including microphones and loudspeakers.[1]

In 1938 A.F. Knoblaugh invented a pickup for stringed instruments involving 2 stacked coils (Pat.No. 2,119,584,). This pickup was to be used in pianos, since he was working for Baldwin at the time.

To overcome the hum problem for guitars, the humbucking pickup was invented by Seth Lover of Gibson under instruction of then President Ted McCarty. About the same time Ray Butts developed a similar pickup that was taken up by Gretsch guitars. Although Gibson's patent was filed almost 2 years before Gretsch's, Gibson's patent was issued 4 weeks after Gretsch's. Both patents describe a reverse wound and reverse polarity pair of coils.[2][3]

A successful early humbucking pickup was the so-called PAF (literally "Patent Applied For") invented by Seth Lover in 1955.[4] Because of this, and because of its use on the Gibson Les Paul guitar, the humbucker is strongly associated with Gibson, although humbuckers have been used in many different guitar designs by many different manufacturers. Humbuckers are also known as dual-coil, double-coil, or hum-canceling pickups. Rickenbacker offered dual coil pickups arranged in a humbucking pattern beginning in late 1953 but dropped the design in 1954 due to the perceived distorted sound. The Gibson Les Paul was the first guitar to use humbuckers in substantial production, but since then, even some models of Fender Stratocasters and Telecasters, traditionally fitted with single-coil pickups, are factory-equipped with humbuckers. Stratocasters fitted with one humbucker in the bridge position, resulting in a pickup configuration noted as H-S-S (starting at bridge pickup: H for humbucker, S for single coil) are referred to as "Fat Strats", because of the "fatter", "rounder" tone offered by the humbucking pickup.

How humbuckers work[edit]

In any magnetic pickup, a vibrating guitar string, magnetized by a fixed magnet within the pickup induces an alternating voltage across its coil(s). However, wire coils also make excellent antennae and are therefore sensitive to electromagnetic interference caused by alternating magnetic fields from mains wiring (mains hum) and electrical appliances like transformers, motors, and computer screens. Guitar pickups reproduce this noise, which can be quite audible, sounding like a constant hum or buzz.

The direction of a voltage induced across a coil by the moving string depends on both the coil winding direction and the direction of the fixed magnets. A humbucker has two coils wound in opposite directions, one clockwise and the other counterclockwise. The magnets in the two coils are arranged in opposite directions so that the string motion induces voltages across both coils in the same direction. Electromagnetic interference, on the other hand, induces voltages in opposing directions across the coils because it is only sensitive to the winding direction. When the signals from both coils are summed together, usually by connecting the coils in series, the two noise voltages cancel, while the signal voltages add thus dramatically improving the signal-to-noise ratio. The technique has something in common with what electrical engineers call common-mode rejection and is also found in balanced lines in audio recording.

Humbuckers on a Gibson Invader.

Alternative humbucker designs[edit]

Stacked humbuckers[edit]

Solid-body guitars, such as Fender Stratocasters, usually feature cavities only for single-coil pickups. Installing full-sized humbuckers requires additional routing of the woodwork and cutting of the pickguard (if the instrument has a pickguard). If the process is not carefully done, the instrument's body and pickguard may be damaged. For most guitarists, this is unacceptable; especially for expensive vintage guitars where it is vital to preserve cosmetic appearance. As a result, many pickup manufacturers now produce humbucking pickups compacted into the size of a single coil, accomplished by vertically "stacking" the coils instead of placing them side-by-side as in a regular humbucker. Many different kinds of stacked humbuckers are available from several manufacturers, producing a wide range of different tones.

Rail humbuckers[edit]

Another design known as rail humbuckers divides a single coil-size pickup in half lengthwise, and the windings are wound around two pole pieces, typically resembling a rail. These pickups look like a normal, albeit smaller, humbucker. This, however, is typically used in conjunction with stacked humbuckers, to produce a high-output pickup. This design can also extend to a "quadrail", by using a rail humbucker for each "single coil" of a normal humbucker.

The same type of rails can also be found in a normal-size humbucker, however. Heavy metal guitarist Dimebag Darrell made heavy use of this type of pickup wired in the bridge position. These tend to also sound fuller and have a higher output and attack than the single coil-size version.

Coil splits[edit]

Some guitars which have humbucking pickups feature "coil splits", which allow the pickups to act as "pseudo-single" coils by either short-circuiting or bypassing one coil. The electrical circuit of the pickup is reduced to that of a true single coil so there is no hum canceling effect. Usually, this feature is activated using a miniature toggle switch or a DPDT push-pull switch mounted on a potentiometer. Some guitars (e.g. the Peavey T-60 and the Fender Classic Player Jaguar HH) make use of a variable coil split circuit that allows the guitarist to dial a variable amount of signal from the second coil, from pure single-coil to full humbucker and everything in-between.

Coil splits are often wrongly referred to as a "coil tap". Coil taps are most commonly found on single coil pickups, and involve an extra hook-up wire being included during the manufacture of the pickup so the guitarist can choose to have all the windings of the pickup included in the circuit, for a fatter, higher output sound with more midrange; or switch the output to "Tap" into the windings at a point that is less than the full coil for a brighter, lower output, cleaner sound. By example: a full pickup coil may be 10,000 turns of wire and the "Tap" may be at 8000 turns. Because of the confusion between coil splits and coil taps - and the rareness of coil taps in general - it is difficult to find tappable single coil pickups for sale. However, pickup manufacturer Seymour Duncan offers tapped versions of many of their Telecaster and Stratocaster pickups on their website at an increased cost.

Notable humbucker designs[edit]

  • Gibson "PAF" - Seth Lover's famous humbucker design
  • Gretsch Filter'Tron Prototype - Ray Butts' first humbucker design[5][6]
  • Fender Wide Range - Fender's first humbucker design, also by Seth Lover
  • Epiphone (and later Gibson) mini-humbucker - a smaller humbucker design with adjustable pole pieces. An Epiphone design from the 1950s originally, they were later used most famously in their Les Paul Deluxe.
  • Gibson Firebird pickup - inspired by the Epiphone pickup, and shares its basic dimensions, but is different in terms of design, appearance, and tone, utilizing single blade pole pieces.
  • Q-tuner: neodymium magnet humbuckers
  • EMG Pickups - Active pickups since 1976
  • Gretsch FilterTron - from 1957 to present; famously used on the Country Gentleman and other hollow-body guitars.

Other noise-reducing pickup designs[edit]

While the original humbucker remains the most common noise-reducing pickup design, inventors have tried many other approaches to reducing noise in guitar pickups.

Many instruments will use a combination of separate single coil pickups in a hum reducing configuration, where the magnetic polarity is different and the coils are electrically reversed. This arrangement is similar to that of a humbucking pickup and noise is effectively reduced. Some examples of this are the Fender Jazz Bass, introduced in 1960, which has used a pair of single coil pickups, one near the bridge and another one about half way between the bridge and the neck, and many Stratocaster style guitars, which often have 3 pickups with the middle one reversed electrically and magnetically. The (usually) 5-way selector switch allows 2 humbucking settings, where the reversed middle pickup is used in parallel with either the bridge or neck pickup.

In 1957, Fender introduced a split pickup to its Precision Bass, which was wired in humbucking fashion, with one coil serving the E and A strings, the other the D and G strings. Both coils pick up the same hum, but since each string is only served by one coil, a single-coil sound is provided. The concept of this later expanded to G&L's Z-coil pickup, which is used for standard guitars such as their Comanche model.

In 1985, Lace Music Products introduced the Lace Sensor pickups, which utilize a proprietary hum-screening bobbins to reduce hum while preserving single-coil tone.[7]

In 1996, Kinman Guitar Electrix introduced replacement pickups for Stratocaster and Telecaster guitars. These were of the stacked humbucker design, where the lower pickup coil functions solely to cancel hum.[8]

See also[edit]

External links[edit]

References[edit]

  1. ^ Mix, June 17, 2005. "Al Kahn (1906–2005)". Retrieved on August 24, 2009.
  2. ^ http://www.google.com/patents/US2896491
  3. ^ http://www.google.com/patents/US2892371
  4. ^ "Seth Lover interview 1978 vintage gibson PAF humbucking humbucker pickups guitars". Provide.net. Retrieved 2013-05-02. 
  5. ^ By Rich Kienzie, "Riffs, Amps, and Butts", Guitar Player Magazine, March 1990, P.14
  6. ^ Joseph Raymond Butts, U.S. Patent 2892371, Issued 6-22-1959
  7. ^ http://www.lacemusic.com/sensors.php
  8. ^ "Humbucker Pickups". Kinman. Retrieved 2013-05-02.