Parametric oscillator

A parametric oscillator is a harmonic oscillator whose parameters oscillate in time. For example, a well known parametric oscillator is a child pumping a swing by periodically standing and squatting to increase the size of the swing's oscillations. The varying of the parameters drives the system. Examples of parameters that may be varied are its resonance frequency ω and damping β.

Parametric oscillators are used in many applications. The classical varactor parametric oscillator will oscillate when the diode's capacitance is varied periodically. The circuit that varies the diode's capacitance is called the "pump" or "driver". In microwave electronics, waveguide/YAG based parametric oscillators operate in the same fashion. The designer varies a parameter periodically in order to induce oscillations.

Parametric oscillators have been developed as low-noise amplifiers, especially in the radio and microwave frequency range. Thermal noise is minimal, since a reactance (not a resistance) is varied. Another common use is frequency conversion, e.g., conversion from audio to radio frequencies. For example, the Optical parametric oscillator converts an input laser wave into two output waves of lower frequency (ω_s,ω_i).

Parametric resonance occurs in a mechanical system when a system is parametrically excited and oscillates at one of its resonant frequencies. Parametric excitation differs from forcing since the action appears as a time varying modification on a system parameter. This effect is different from regular resonance because it exhibits the instability phenomenon.

History

Michael Faraday (1831) was the first to notice oscillations of one frequency being excited by forces of double the frequency, in the crispations (ruffled surface waves) observed in a wine glass excited to "sing". Melde (1859) generated parametric oscillations in a string by employing a tuning fork to periodically vary the tension at twice the resonance frequency of the string. Parametric oscillation was first treated as a general phenomenon by Rayleigh (1883,1887).

Parametric amplifiers (paramps) were first used in 1913-1915 for radio telephony from Berlin to Vienna and Moscow, and were predicted to have a useful future (Ernst Alexanderson, 1916). The early paramps varied inductances, but other methods have been developed since, e.g., the varactor diodes, klystron tubes, Josephson junctions and optical methods.

The mathematics

$\frac{d^{2}x}{dt^{2}} + \beta(t) \frac{dx}{dt} + \omega^{2}(t) x = 0$

This equation is linear in x(t). By assumption, the parameters ω² and β depend only on time and do not depend on the state of the oscillator. In general, β(t) and/or ω²(t) are assumed to vary periodically, with the same period T.

Remarkably, if the parameters vary at roughly twice the natural frequency of the oscillator (defined below), the oscillator phase-locks to the parametric variation and absorbs energy at a rate proportional to the energy it already has. Without a compensating energy-loss mechanism provided by β, the oscillation amplitude grows exponentially. (This phenomenon is called parametric excitation, parametric resonance or parametric pumping.) However, if the initial amplitude is zero, it will remain so; this distinguishes it from the non-parametric resonance of driven simple harmonic oscillators, in which the amplitude grows linearly in time regardless of the initial state.

A familiar experience of both parametric and driven oscillation is playing on a swing. Rocking back and forth pumps the swing as a driven harmonic oscillator, but once moving, the swing can also be parametrically driven by alternately standing and squatting at key points in the swing. This changes moment of inertia of the swing and hence the resonance frequency, and children can quickly reach large amplitudes provided that they have some amplitude to start with (e.g., get a push). Standing and squatting at rest, however, goes nowhere.

Transformation of the equation

We begin by making a change of variables

$q(t) \ \stackrel{\mathrm{def}}{=}\ e^{D(t)} x(t)$

where D(t) is a time integral of the damping

$D(t) \ \stackrel{\mathrm{def}}{=}\ \frac{1}{2} \int^{t} d\tau \ \beta(\tau).$

This change of variables eliminates the damping term

$\frac{d^{2}q}{dt^{2}} + \Omega^{2}(t) q = 0$

where the transformed frequency is defined

$\Omega^{2}(t) = \omega^{2}(t) - \frac{1}{2} \left( \frac{d\beta}{dt} \right) - \frac{1}{4} \beta^{2}.$

In general, the variations in damping and frequency are relatively small perturbations

$\beta(t) = \omega_{0} \left[b + g(t) \right]$

$\omega^{2}(t) = \omega_{0}^{2} \left[1 + h(t) \right]$

where ω₀ and bω₀ are constants, namely, the time-averaged oscillator frequency and damping, respectively. The transformed frequency can be written in a similar way:

$\Omega^{2}(t) = \omega_{n}^{2} \left[1 + f(t) \right],$

where ω_n is the natural frequency of the damped harmonic oscillator

$\omega_{n}^{2} \ \stackrel{\mathrm{def}}{=}\ \omega_{0}^{2} \left( 1 - \frac{b^{2}}{4} \right)$

and

$\omega_{n}^{2} f(t) \ \stackrel{\mathrm{def}}{=}\ \omega_{0}^{2} \left\{h(t) - \frac{1}{2\omega_{0}} \left( \frac{dg}{dt} \right) - \frac{b}{2} g(t) - \frac{1}{4} g^{2}(t)\right\}.$

Thus, our transformed equation can be written

$\frac{d^{2}q}{dt^{2}} + \omega_{n}^{2} \left[1 + f(t) \right] q = 0.$

Remarkably, the independent variations g(t) and h(t) in the oscillator damping and resonance frequency, respectively, can be combined into a single pumping function f(t). The converse conclusion is that any form of parametric excitation can be accomplished by varying either the resonance frequency or the damping, or both.

Solution of the transformed equation

Let us assume that f(t) is sinusoidal, specifically

f(t) = f₀sin 2ω_pt

where the pumping frequency $2\omega_{p} \approx 2\omega_{n}$ but need not equal 2ω_n exactly. The solution q(t) of our transformed equation may be written

q(t) = A(t)cos ω_pt + B(t)sin ω_pt

where we have factored out the rapidly varying components (cos ω_pt and sin ω_pt) to isolate the slowly varying amplitudes A(t) and B(t). This corresponds to Laplace's variation of parameters method.

Substituting this solution into the transformed equation and retaining only the terms first-order in $f_{0} \ll 1$ yields two coupled equations

$2\omega_{p} \frac{dA}{dt} = \left( \frac{f_{0}}{2} \right) \omega_{n}^{2} A - \left( \omega_{p}^{2} - \omega_{n}^{2} \right) B$

$2\omega_{p} \frac{dB}{dt} = -\left( \frac{f_{0}}{2} \right) \omega_{n}^{2} B + \left( \omega_{p}^{2} - \omega_{n}^{2} \right) A$

We may decouple and solve these equations by making another change of variables

$A(t) \ \stackrel{\mathrm{def}}{=}\ r(t) \cos \theta(t)$

$B(t) \ \stackrel{\mathrm{def}}{=}\ r(t) \sin \theta(t)$

which yields the equations

$\frac{dr}{dt} = \left( \alpha_{\mathrm{max}} \cos 2\theta \right) r$

$\frac{d\theta}{dt} = -\alpha_{\mathrm{max}} \left[\sin 2\theta - \sin 2\theta_{\mathrm{eq}} \right]$

where we have defined for brevity

$\alpha_{\mathrm{max}} \ \stackrel{\mathrm{def}}{=}\ \frac{f_{0} \omega_{n}^{2}}{4\omega_{p}}$

$\sin 2\theta_{\mathrm{eq}} \ \stackrel{\mathrm{def}}{=}\ \left( \frac{2}{f_{0}} \right) \epsilon$

and the detuning

$\epsilon \ \stackrel{\mathrm{def}}{=}\ \frac{\omega_{p}^{2} - \omega_{n}^{2}}{\omega_{n}^{2}}$

The θ equation does not depend on r, and linearization near its equilibrium position θ_eq shows that θ decays exponentially to its equilibrium

$\theta(t) = \theta_{\mathrm{eq}} + \left( \theta_{0} - \theta_{\mathrm{eq}} \right) e^{-2\alpha t}$

where the decay constant

$\alpha \ \stackrel{\mathrm{def}}{=}\ \alpha_{\mathrm{max}} \cos 2\theta_{\mathrm{eq}}$.

In other words, the parametric oscillator phase-locks to the pumping signal f(t).

Taking θ(t) = θ_eq (i.e., assuming that the phase has locked), the r equation becomes

$\frac{dr}{dt} = \alpha r$

whose solution is r(t) = r₀e^αt; the amplitude of the q(t) oscillation diverges exponentially. However, the corresponding amplitude R(t) of the untransformed variable $x \ \stackrel{\mathrm{def}}{=}\ q e^{-D(t)}$ need not diverge

R(t) = r(t)e ^{− D(t)} = r₀e^{αt − D(t)}

The amplitude R(t) diverges, decays or stays constant, depending on whether αt is greater than, less than, or equal to D(t), respectively.

The maximum growth rate of the amplitude occurs when ω_p = ω_n. At that frequency, the equilibrium phase θ_eq is zero, implying that cos 2θ_eq = 1 and α = α_max. As ω_p is varied from ω_n, θ_eq moves away from zero and α < α_max, i.e., the amplitude grows more slowly. For sufficiently large deviations of ω_p, the decay constant α can become purely imaginary since

$\alpha = \alpha_{\mathrm{max}} \sqrt{1- \left( \frac{2}{f_{0}} \right)^{2} \epsilon^{2}}$

If the detuning $\epsilon$ exceeds f₀ / 2, α becomes purely imaginary and q(t) varies sinusoidally. Using the definition of the detuning $\epsilon$, the pumping frequency 2ω_p must lie between $2\omega_{n} \sqrt{1 - \frac{f_{0}}{2}}$ and $2\omega_{n} \sqrt{1 + \frac{f_{0}}{2}}$ in order to achieve exponetial growth in q. Expanding the square roots in a binomial series shows that the spread in pumping frequencies that result in exponentially growing q is approximately ω_nf₀.

Intuitive derivation of parametric excitation

The above derivation may seem like a mathematical sleight-of-hand, so it may be helpful to give an intuitive derivation. The q equation may be written in the form

$\frac{d^{2}q}{dt^{2}} + \omega_{n}^{2} q = -\omega_{n}^{2} f(t) q$

which represents a simple harmonic oscillator (or, alternatively, a bandpass filter) being driven by a signal $-\omega_{n}^{2} f(t) q$ that is proportional to its response q.

Assume that q(t) = Acos ω_pt already has an oscillation at frequency ω_p and that the pumping f(t) = f₀sin2ω_pt has double the frequency and a small amplitude $f_{0} \ll 1$. Applying a trigonometric identity for products of sinusoids, their product q(t)f(t) produces two driving signals, one at frequency ω_p and the other at frequency 3ω_p

$f(t)q(t) = \frac{f_{0}}{2} A \left( \sin \omega_{p} t + \sin 3\omega_{p} t \right)$

Being off-resonance, the 3ω_p signal is attentuated and can be neglected initially. By contrast, the ω_p signal is on resonance, serves to amplify q and is proportional to the amplitude A. Hence, the amplitude of q grows exponentially unless it is initially zero.

Expressed in Fourier space, the multiplication f(t)q(t) is a convolution of their Fourier transforms $\tilde{F}(\omega)$ and $\tilde{Q}(\omega)$. The positive feedback arises because the + 2ω_p component of f(t) converts the − ω_p component of q(t) into a driving signal at + ω_p, and vice versa (reverse the signs). This explains why the pumping frequency must be near 2ω_n, twice the natural frequency of the oscillator. Pumping at a grossly different frequency would not couple (i.e., provide mutual positive feedback) between the − ω_p and + ω_p components of q(t).

Parametric resonance

Parametric resonance is the parametrical resonance phenomenon of mechanical excitation and oscillation at certain frequencies (and the associated harmonics). This effect is different from regular resonance because it exhibits the instability phenomenon.

Parametric resonance occurs in a mechanical system when a system is parametrically excited and oscillates at one of its resonant frequencies.Parametric resonance takes place when the external excitation frequency equals to twice the natural frequency of the system. Parametric excitation differs from forcing since the action appears as a time varying modification on a system parameter. The classical example of parametric resonance is that of the vertically forced pendulum.

For small amplitudes and by linearising, the stability of the periodic solution is given by :

$\ddot{u} + (a + B \cos t)u =0 \$

where u is some perturbation from the periodic solution. Here the $B\ \cos(t)$ term acts as an ‘energy’ source and is said to parametrically excite the system. The Mathieu equation describes many other physical systems to a sinusoidal parametric excitation such as an LC Circuit where the capacitor plates move sinusoidally.

Parametric amplifiers

Introduction

A parametric amplifier is implemented as a mixer. The mixer's gain shows up in the output as amplifier gain. The input weak signal is mixed with a strong local oscillator signal, and the resultant strong output is used in the ensuing receiver stages.

Parametric amplifiers also operate by changing a parameter of the amplifier. Intuitively, this can be understood as follows, for a variable capacitor based amplifier.

Q [charge in a capacitor] = C x V
therefore
V [voltage across a capacitor] = Q/C

Knowing the above, if a capacitor is charged until its voltage equals the sampled voltage of an incoming weak signal, and if the capacitor's capacitance is then reduced (say, by manually moving the plates further apart), then the voltage across the capacitor will increase. In this way, the voltage of the weak signal is amplified.

If the capacitor is a varicap diode, then the 'moving the plates' can be done simply by applying time-varying DC voltage to the varicap diode. This driving voltage usually comes from another oscillator — sometimes called a "pump".

The resulting output signal contains frequencies that are the sum and difference of the input signal (f1) and the pump signal (f2): (f1 + f2) and (f1 - f2).

A practical parametric oscillator needs the following connections: one for the "common" or "ground", one to feed the pump, one to retrieve the output, and maybe a fourth one for biasing. A parametric amplifier needs a fifth port to input the signal being amplified. Since a varactor diode has only two connections, it can only be a part of an LC network with four eigenvectors with nodes at the connections. This can be implemented as a transimpedance amplifier, a traveling wave amplifier or by means of a circulator.

Mathematical equation

The parametric oscillator equation can be extended by adding an external driving force E(t):

$\frac{d^{2}x}{dt^{2}} + \beta(t) \frac{dx}{dt} + \omega^{2}(t) x = E(t).$

We assume that the damping D is sufficiently strong that, in the absence of the driving force E, the amplitude of the parametric oscillations does not diverge, i.e., that αt < D. In this situation, the parametric pumping acts to lower the effective damping in the system. For illustration, let the damping be constant β(t) = ω₀b and assume that the external driving force is at the mean resonance frequency ω₀, i.e., E(t) = E₀sin ω₀t. The equation becomes

$\frac{d^{2}x}{dt^{2}} + b \omega_{0} \frac{dx}{dt} + \omega_{0}^{2} \left[1 + h_{0} \sin 2\omega_{0} t \right] x = E_{0} \sin \omega_{0} t$

whose solution is roughly

$x(t) = \frac{2E_{0}}{\omega_{0}^{2} \left( 2b - h_{0} \right)} \cos \omega_{0} t.$

As h₀ approaches the threshold 2b, the amplitude diverges. When $h \geq 2b$, the system enters parametric resonance and the amplitude begins to grow exponentially, even in the absence of a driving force E(t).

Advantages

1:It is highly sensitive.

2:low noise level amplifier for ultra high frequency and microwave radio signal.

Other relevant mathematical results

If the parameters of any second-order linear differential equation are varied periodically, Floquet analysis shows that the solutions must vary either sinusoidally or exponentially.

The q equation above with periodically varying f(t) is an example of a Hill equation. If f(t) is a simple sinusoid, the equation is called a Mathieu equation.

See also

• Harmonic oscillator
• Optical parametric oscillator
• Optical parametric amplifier
• Mathieu equation

Further reading

• Kühn L. (1914) Elektrotech. Z., 35, 816-819.
• Mumford WW. (1960) "Some Notes on the History of Parametric Transducers", Proceedings of the Institute of Radio Engineers, 48, 848-853.
• Pungs L. DRGM Nr. 588 822 (24 October 1913); DRP Nr. 281440 (1913); Elektrotech. Z., 44, 78-81 (1923?); Proc. IRE, 49, 378 (1961).

External articles

• Elmer, Franz-Josef, "Parametric Resonance". unibas.ch, July 20, 1998.
• Cooper, Jeffery, "Parametric Resonance in Wave Equations with a Time-Periodic Potential". SIAM Journal on Mathematical Analysis, Volume 31, Number 4, pp. 821–835. Society for Industrial and Applied Mathematics, 2000 .
• "Driven Pendulum: Parametric Resonance". phys.cmu.edu (Demonstration of physical mechanics or classical mechanics. Resonance oscillations set up in a simple pendulum via periodically varying pendulum length.)