Jump to content

Drop tube

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Citation bot (talk | contribs) at 03:40, 8 October 2020 (Add: s2cid, author pars. 1-1. Removed parameters. Some additions/deletions were actually parameter name changes. | You can use this bot yourself. Report bugs here. | Suggested by Abductive | Category:Laboratory equipment | via #UCB_Category). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

In physics and materials science, a drop tower or drop tube is a structure used to produce a controlled period of weightlessness for an object under study. Air bags, polystyrene pellets, and magnetic or mechanical brakes are sometimes used to arrest the fall of the experimental payload. In other cases, high-speed impact with a substrate at the bottom of the tower is an intentional part of the experimental protocol.

Not all such facilities are towers - NASA Glenn's Zero Gravity Research Facility is based on a vertical shaft, extending to 510 feet (155 m) below ground level.

Typical operation

A view down the tube of NASA Glenn's 5 second Zero Gravity Facility.
A view down the shaft of NASA Glenn's 2.2 second drop tower. A large (deflated) air bag is at the bottom.

For a typical materials science experiment, a sample of the material under study is loaded into the top of the drop tube, which is filled with inert gas or evacuated to create a low-pressure environment. Following any desired preprocessing (e.g. induction heating to melt a metal alloy), the sample is released to fall to the bottom of the tube. During its flight or upon impact the sample can be characterized with instruments such as cameras and pyrometers.

Drop towers are also commonly used in combustion research. For this work, oxygen must be present and the payload may be enclosed in a drag shield to isolate it from high-speed "wind" as the apparatus accelerates toward the bottom of the tower. See a video of a microgravity combustion experiment in the NASA Glenn Five Second Drop Facility at [1].

Fluid physics experiments and development and testing of space-based hardware can also be conducted using a drop tower. Sometimes, the ground-based research performed with a drop tower serves as a prelude to more ambitious, in-flight investigation; much longer periods of weightlessness can be achieved with parabolic-flight-path aircraft or with space-based laboratories aboard the Space Shuttle or the International Space Station.

The duration of free-fall produced in a drop tube depends on the length of the tube and its degree of internal evacuation. The 105-meter drop tube at Marshall Space Flight Center produces 4.6 seconds of weightlessness when it is fully evacuated. In the drop facility Fallturm Bremen at University of Bremen a catapult can be used to throw the experiment upwards to prolong the weightlessness from 4.74 to nearly 9.3 seconds.[1][2] Negating the physical space needed for the initial acceleration, this technique doubles the effective period of weightlessness. The NASA Glenn Research Center has a 5 second drop tower (The Zero Gravity Facility) and a 2.2 second drop tower (The 2.2 Second Drop Tower).

Much of the operating cost of a drop tower is due to the need for evacuation of the drop tube, to eliminate the effect of aerodynamic drag. Alternatively the experiment is placed inside an outer box (the drag shield) for which, due to its weight, during its fall the reduction of acceleration due to air drag is less.

Historical uses

Though the story may be apocryphal, Galileo is popularly thought to have used the Leaning Tower of Pisa as a drop tower to demonstrate that falling bodies accelerate at the same constant rate regardless of their mass.

Drop towers called shot towers were once useful for making lead shot. A short period of weightlessness allows molten lead to solidify into a quasi-perfect sphere by the time it reaches the floor of the tower.

Drop tubes are used for handloading black powder; the drop allows the powder to settle into a case, improving the compression of powder charges.[citation needed]

List of drop towers


See also

References

  1. ^ VON KAMPEN, P., KÖNEMANN, T., and RATH, H.J. (2010). The drop tower bremen – an overview, in COSPAR, Proceedings of the 38th COSPAR Scientific Assembly, Bremen, Germany, 15–18 July 2010. p. 3587. Available from: http://adsabs.harvard.edu/abs/2010cosp...38.3587V [Accessed: 14 June 2011]
  2. ^ KÖNEMANN, T., VON KAMPEN, P., and RATH, H.J. (2010). The drop tower bremen – experiment operation, in COSPSAR, Proceedings of the 38th COSPAR Scientific Assembly, Bremen, Germany, 15–18 July 2010. volume 38 of COSPAR, Plenary Meeting. p. 3588. Available from: http://adsabs.harvard.edu/cgi-bin/nph-data_query?bibcode=2010cosp...38.3588K&link_type=ARTICLE&db_key=AST&high= [Accessed: 14 June 2011]
  3. ^ http://www.mext.go.jp/a_menu/kaihatu/space/kaihatsushi/detail/1299905.htm [In Japanese]
  4. ^ "宇宙環境利用". www.hastic.jp. Retrieved 2020-01-14.
  5. ^ Zhang, X.; Yuan, L.; WU; Tian, L.; YAO, K. (2005). "Some key technics of drop tower experiment device of national microgravity laboratory (China) (NMLC)". Science in China Series E: Technological Sciences. 48 (3): 305–316. Bibcode:2005ScChE..48..305Z. doi:10.1360/102004-21. S2CID 110511662.
  6. ^ A Year In The Life Of Kew Gardens, 2007, pg86, Joanna Jackson
  7. ^ Steinberg, T. (2008). "Reduced Gravity Testing and Research Capabilities at Queensland University of Technology's New 2.0 Second Drop Tower". Advanced Materials Research. 32: 21–24. doi:10.4028/www.scientific.net/amr.32.21. S2CID 44240229.
  8. ^ Plagens, Owen; Castillo, Martin; Steinberg, Theodore; Ong, Teng-Cheong (2014). "Drop Tower Facility at Queensland University of Technology". Cosp. 40: G0.2–1–14-1. Bibcode:2014cosp...40E2560P.