This article needs additional citations for verification. (May 2017) (Learn how and when to remove this template message)
Anisotropy (/ /-,) is the property of being directionally dependent, which implies different properties in different directions, as opposed to isotropy. It can be defined as a difference, when measured along different axes, in a material's physical or mechanical properties (absorbance, refractive index, conductivity, tensile strength, etc.)
Fields of interest
Anisotropic filtering (AF) is a method of enhancing the image quality of textures on surfaces that are far away and steeply angled with respect to the point of view. Older techniques, such as bilinear and trilinear filtering, do not take into account the angle a surface is viewed from, which can result in aliasing or blurring of textures. By reducing detail in one direction more than another, these effects can be reduced.
A chemical anisotropic filter, as used to filter particles, is a filter with increasingly smaller interstitial spaces in the direction of filtration so that the proximal regions filter out larger particles and distal regions increasingly remove smaller particles, resulting in greater flow-through and more efficient filtration.
In NMR spectroscopy, the orientation of nuclei with respect to the applied magnetic field determines their chemical shift. In this context, anisotropic systems refer to the electron distribution of molecules with abnormally high electron density, like the pi system of benzene. This abnormal electron density affects the applied magnetic field and causes the observed chemical shift to change.
In fluorescence spectroscopy, the fluorescence anisotropy, calculated from the polarization properties of fluorescence from samples excited with plane-polarized light, is used, e.g., to determine the shape of a macromolecule. Anisotropy measurements reveal the average angular displacement of the fluorophore that occurs between absorption and subsequent emission of a photon.
Images of a gravity-bound or man-made environment are particularly anisotropic in the orientation domain, with more image structure located at orientations parallel with or orthogonal to the direction of gravity (vertical and horizontal).
Physicists from University of California, Berkeley reported about their detection of the cosine anisotropy in cosmic microwave background radiation in 1977. Their experiment demonstrated the Doppler shift caused by the movement of the earth with respect to the early Universe matter, the source of the radiation. Cosmic anisotropy has also been seen in the alignment of galaxies' rotation axes and polarisation angles of quasars.
Physicists use the term anisotropy to describe direction-dependent properties of materials. Magnetic anisotropy, for example, may occur in a plasma, so that its magnetic field is oriented in a preferred direction. Plasmas may also show "filamentation" (such as that seen in lightning or a plasma globe) that is directional.
An anisotropic liquid has the fluidity of a normal liquid, but has an average structural order relative to each other along the molecular axis, unlike water or chloroform, which contain no structural ordering of the molecules. Liquid crystals are examples of anisotropic liquids.
Some materials conduct heat in a way that is isotropic, that is independent of spatial orientation around the heat source. Heat conduction is more commonly anisotropic, which implies that detailed geometric modeling of typically diverse materials being thermally managed is required. The materials used to transfer and reject heat from the heat source in electronics are often anisotropic.
Many crystals are anisotropic to light ("optical anisotropy"), and exhibit properties such as birefringence. Crystal optics describes light propagation in these media. An "axis of anisotropy" is defined as the axis along which isotropy is broken (or an axis of symmetry, such as normal to crystalline layers). Some materials can have multiple such optical axes.
Geophysics and Geology
Seismic anisotropy is the variation of seismic wavespeed with direction. Seismic anisotropy is an indicator of long range order in a material, where features smaller than the seismic wavelength (e.g., crystals, cracks, pores, layers or inclusions) have a dominant alignment. This alignment leads to a directional variation of elasticity wavespeed. Measuring the effects of anisotropy in seismic data can provide important information about processes and mineralogy in the Earth; indeed, significant seismic anisotropy has been detected in the Earth's crust, mantle and inner core.
Geological formations with distinct layers of sedimentary material can exhibit electrical anisotropy; electrical conductivity in one direction (e.g. parallel to a layer), is different from that in another (e.g. perpendicular to a layer). This property is used in the gas and oil exploration industry to identify hydrocarbon-bearing sands in sequences of sand and shale. Sand-bearing hydrocarbon assets have high resistivity (low conductivity), whereas shales have lower resistivity. Formation evaluation instruments measure this conductivity/resistivity and the results are used to help find oil and gas in wells.
The hydraulic conductivity of aquifers is often anisotropic for the same reason. When calculating groundwater flow to drains or to wells, the difference between horizontal and vertical permeability must be taken into account, otherwise the results may be subject to error.
Most common rock-forming minerals are anisotropic, including quartz and feldspar. Anisotropy in minerals is most reliably seen in their optical properties. An example of an isotropic mineral is garnet.
Anisotropy is also a well-known property in medical ultrasound imaging describing a different resulting echogenicity of soft tissues, such as tendons, when the angle of the transducer is changed. Tendon fibers appear hyperechoic (bright) when the transducer is perpendicular to the tendon, but can appear hypoechoic (darker) when the transducer is angled obliquely. This can be a source of interpretation error for inexperienced practitioners.
Materials Science and Engineering
Anisotropy, in materials science, is a material's directional dependence of a physical property. This is a critical consideration for materials selection in engineering applications. For monocrystalline material, anisotropy is associated with the crystal symmetry. Tensor descriptions of material properties can be used to determine the directional dependence of that property. When a material is polycrystalline, the directional dependence on properties is often related to the processing techniques it has undergone. A material with randomly oriented grains will be isotropic, whereas materials with texture will be often be anisotropic. Textured materials are often the result of processing techniques like hot rolling, wire-drawing, and heat treatments.
Mechanical properties of materials, such as Young's modulus, creep, are often dependent on the direction of measurement. Fourth rank tensor properties, like the elastic constants, are anisotropic, even for materials with cubic symmetry. The Young's modulus relates stress and strain when an isotropic material is elastically deformed; to describe elasticity in an anisotropic material, stiffness (or compliance) tensors are used instead. In metals, anisotropic elasticity behavior is prevalent in all single crystals, with the exception of Tungsten, due to the fact there are only two independent stiffness coefficients in the stiffness tensor (while other cubic crystals have three). For face centered cubic materials like Copper, the elastic modulus is highest along the <111> direction, normal to the close packed planes.
The anisotropy ratio is a value computed to compare elastic anisotropy in materials. It is given by the following expression:
where the C values are stiffness coefficients in Voight notation. For an isotropic material, the ratio is one.
Fiber-reinforced or layered composite materials exhibit anisotropic mechanical properties, due to orientation of the reinforcement material. In many fiber-reinforced composites like carbon fiber or glass fiber based composites, the weave of the material (e.g. unidirectional or plain weave) can determine the extent of the anisotropy of the bulk material. The tunability of orientation of the fibers, allows for application-based designs of composite materials, depending on the direction of stresses applied onto the material.
Amorphous materials such as glass and polymers are typically isotropic. Due to the highly randomized orientation of macromolecules in polymeric materials, polymers are in general described as isotropic. However, polymers can be engineered to have directionally dependent properties through processing techniques or introduction of anisotropy-inducing elements. Researchers have built composite materials with aligned fibers and voids to generate anisotropic hydrogels, in order to mimic hierarchically ordered biological soft matter. 3D printing, especially Fused Deposition Modeling, can introduce anisotropy into printed parts. This is due to the fact that FDM is designed to extrude and print layers of thermoplastic materials. This creates materials that are strong when tensile stress is applied in parallel to the layers and weak when the material is perpendicular to the layers.
Anisotropic etching techniques (such as deep reactive ion etching) are used in microfabrication processes to create well defined microscopic features with a high aspect ratio. These features are commonly used in MEMS and microfluidic devices, where the anisotropy of the features is needed to impart desired optical, electrical, or physical properties to the device. Anisotropic etching can also refer to certain chemical etchants used to etch a certain material preferentially over certain crystallographic planes (e.g., KOH etching of silicon  produces pyramid-like structures)
Diffusion tensor imaging is an MRI technique that involves measuring the fractional anisotropy of the random motion (Brownian motion) of water molecules in the brain. Water molecules located in fiber tracts are more likely to be anisotropic, since they are restricted in their movement (they move more in the dimension parallel to the fiber tract rather than in the two dimensions orthogonal to it), whereas water molecules dispersed in the rest of the brain have less restricted movement and therefore display more isotropy. This difference in fractional anisotropy is exploited to create a map of the fiber tracts in the brains of the individual.
Atmospheric Radiative Transfer
Radiance fields (see BRDF) from a reflective surface are often not isotropic in nature. This makes calculations of the total energy being reflected from any scene a difficult quantity to calculate. In remote sensing applications, anisotropy functions can be derived for specific scenes, immensely simplifying the calculation of the net reflectance or (thereby) the net irradiance of a scene. For example, let the BRDF be where 'i' denotes incident direction and 'v' denotes viewing direction (as if from a satellite or other instrument). And let P be the Planar Albedo, which represents the total reflectance from the scene.
It is of interest because, with knowledge of the anisotropy function as defined, a measurement of the BRDF from a single viewing direction (say, ) yields a measure of the total scene reflectance (Planar Albedo) for that specific incident geometry (say, ).
- Smoot G. F.; Gorenstein M. V. & Muller R. A. (5 October 1977). "Detection of Anisotropy in the Cosmic Blackbody Radiation" (PDF). Lawrence Berkeley Laboratory and Space Sciences Laboratory, University of California, Berkeley. Retrieved 15 September 2013.
- Tian, Xiaojuan; Itkis, Mikhail E; Bekyarova, Elena B; Haddon, Robert C (8 April 2013). "Anisotropic Thermal and Electrical Properties of Thin Thermal Interface Layers of Graphite Nanoplatelet-Based Composites". Scientific Reports. 3: 1710. doi:10.1038/srep01710. PMC 3632880.
- R.J.Oosterbaan, 1997, The energy balance of groundwater flow applied to subsurface drainage in anisotropic soils by pipes or ditches with entrance resistance. On line:  Archived 19 February 2009 at the Wayback Machine. The corresponding free EnDrain program can be downloaded from: .
- R.J.Oosterbaan, 2002, Subsurface drainage by (tube)wells, 9 pp. On line: . The corresponding free WellDrain program can be downloaded from: 
- Newnham, Robert E. Properties of Materials: Anisotropy, Symmetry, Structure (1st ed.). Oxford University Press. ISBN 978-0198520764.
- Courtney, Thomas H. (2005). Mechanical Behavior of Materials (2nd ed.). Waveland Pr Inc. ISBN 978-1577664253.
- "Fabric Weave Styles". Composite Envisions. Retrieved 23 May 2019.
- Sano, Koki; Ishida, Yasuhiro; Aida, Tazuko (16 October 2017). "Synthesis of Anisotropic Hydrogels and Their Applications". Angewandte Chemie International Edition. 57 (10).
- Wang, Xin; Jiang, Man; Gou, Jihua; Hui, David (1 February 2017). "3D printing of polymer matrix composites: A review and prospective". Composites Part B: Engineering. 110: 442–458. doi:10.1016/j.compositesb.2016.11.034.
|Look up anisotropy in Wiktionary, the free dictionary.|