# Differential (mechanical device)

(Redirected from Differential gear)

A differential is a particular type of simple planetary gear train that has the property that the angular velocity of its carrier is the average of the angular velocities of its sun and annular gears. This is accomplished by packaging the gear train so it has a fixed carrier train ratio R = -1, which means the gears corresponding to the sun and annular gears are the same size. This can be done by engaging the planet gears of two identical and coaxial epicyclic gear trains to form a spur gear differential. Another approach is to use bevel gears for the sun and annular gears and a bevel gear as the planet, which is known as a bevel gear differential.

A spur gear differential constructed by engaging the planet gears of two co-axial epicyclic gear trains. The casing is the carrier for this planetary gear train.

## Overview

Automotive differential: The drive gear 2 is mounted on the carrier 5 which supports the planetary bevel gears 4 which engage the driven bevel gears 3 attached to the axles 1.
ZF Differential. The drive shaft enters from the front and the driven axles run left and right.
Car differential of a Škoda 422.

In automobiles and other wheeled vehicles, the differential allows the outer drive wheel to rotate faster than the inner drive wheel during a turn. This is necessary when the vehicle turns, making the wheel that is traveling around the outside of the turning curve roll farther and faster than the other. The average of the rotational speed of the two driving wheels equals the input rotational speed of the drive shaft. An increase in the speed of one wheel is balanced by a decrease in the speed of the other.

When used in this way, a differential couples the input shaft (or prop shaft) to the Pinion, which in turn runs on the Crown wheel of the differential. This also works as reduction gearing to give the ratio. On rear wheel drive vehicles the differential may connect to half-shafts inside an axle casing or drive shafts that connect to the rear driving wheels. Front wheel drive vehicles tend to have the pinion on the end of the main-shaft of the gearbox and the differential is enclosed in the same casing as the gearbox. They have individual drive-shafts to each wheel. Older 4x4 vehicles and tractors usually have a solid front axle, the modern way can be a separate differential and drive shaft arrangement for the front.

A differential consists of one input, the drive shaft, and two outputs which are the two drive wheels, however the rotation of the drive wheels are coupled by their connection to the roadway. Under normal conditions, with small tyre slip, the ratio of the speeds of the two driving wheels is defined by the ratio of the radii of the paths around which the two wheels are rolling, which in turn is determined by the track-width of the vehicle (the distance between the driving wheels) and the radius of the turn.

Non-automotive uses of differentials include performing analog arithmetic. Two of the differential's three shafts are made to rotate through angles that represent (are proportional to) two numbers, and the angle of the third shaft's rotation represents the sum or difference of the two input numbers. The earliest known use of a differential gear is in the Antikythera Mechanism, circa 80 BCE, which used a differential gear to control a small sphere representing the moon from the difference between the sun and moon position pointers. The ball was painted black and white in hemispheres, and graphically showed the phase of the moon at a particular point in time.[1] See also the Chinese South-pointing chariot. An equation clock that used a differential for addition was made in 1720. In the 20th Century, large assemblies of many differentials were used as analog computers, calculating, for example, the direction in which a gun should be aimed. However, the development of electronic digital computers has made these uses of differentials obsolete. Military uses may still exist. See Electromagnetic pulse. Practically all the differentials that are now made are used in automobiles and similar vehicles.

## History

There are many claims to the invention of the differential gear but it is possible that it was known, at least in some places, in ancient times. Some historical milestones of the differential include:

• 1050 BC–771 BC: The Book of Song (which itself was written between 502 and 557 A.D.) makes the assertion that the south-pointing chariot, which may have used a differential gear, was invented during the Western Zhou Dynasty in China.[citation needed]
• 100 BC–70 BC: The Antikythera mechanism has been dated to this period. It was discovered in 1902 on a shipwreck by sponge divers, and modern research suggests that it used a differential gear to determine the angle between the ecliptic positions of the sun and moon, and thus the phase of the moon.[1][2]
• 30 BC–20 BC: Differential gear systems possibly used in China

## Epicyclic differential

Epicyclic gearing is used here to apportion torque asymmetrically. The input shaft is the green hollow one, the yellow is the low torque output, and the pink is the high torque output. The force applied in the yellow and the pink gears is the same, but since the arm of the pink one is 2× to 3× as big, the torque will be 2× to 3× as high.

An epicyclic differential can use epicyclic gearing to split and apportion torque asymmetrically between the front and rear axles. An epicyclic differential is at the heart of the Toyota Prius automotive drive train, where it interconnects the engine, motor-generators, and the drive wheels (which have a second differential for splitting torque as usual). It has the advantage of being relatively compact along the length of its axis (that is, the sun gear shaft).

Epicyclic gears are also called planetary gears because the axes of the planet gears revolve around the common axis of the sun and ring gears that they mesh with and roll between. In the image, the yellow shaft carries the sun gear which is almost hidden. The blue gears are called planet gears and the pink gear is the ring gear or annulus.

## Spur-gear differential

This is another type of differential that was used in some early automobiles, more recently the Oldsmobile Toronado, as well as other non-automotive applications. It consists of spur gears only.

A spur-gear differential has two equal-sized spur gears, one for each half-shaft, with a space between them. Instead of the Bevel gear, also known as a miter gear, assembly (the "spider") at the centre of the differential, there is a rotating carrier on the same axis as the two shafts. Torque from a prime mover or transmission, such as the drive shaft of a car, rotates this carrier.

Mounted in this carrier are one or more pairs of identical pinions, generally longer than their diameters, and typically smaller than the spur gears on the individual half-shafts. Each pinion pair rotates freely on pins supported by the carrier. Furthermore, the pinion pairs are displaced axially, such that they mesh only for the part of their length between the two spur gears, and rotate in opposite directions. The remaining length of a given pinion meshes with the nearer spur gear on its axle. Therefore, each pinion couples that spur gear to the other pinion, and in turn, the other spur gear, so that when the drive shaft rotates the carrier, its relationship to the gears for the individual wheel axles is the same as that in a bevel-gear differential.

A spur gear differential is constructed from two identical coaxial epicyclic gear trains assembled with a single carrier such that their planet gears are engaged. This forms a planetary gear train with a fixed carrier train ratio R = -1.

In this case, the fundamental formula for the planetary gear train yields,

$\frac{\omega_s-\omega_c}{\omega_a-\omega_c}=-1,$

or

$\omega_c = \frac{1}{2}(\omega_s + \omega_a).$

Thus, the angular velocity of the carrier of a spur gear differential is the average of the angular velocities of the sun and annular gears.[5]

In discussing the spur gear differential, the use of the term annular gear is a convenient way to distinguish the sun gears of the two epicyclic gear trains. The second sun gear serves the same purpose as the annular gear of a simple planetary gear train, but clearly does not have the internal gear mate that is typical of an annular gear.

## Non-automotive applications

Differential used to control the take-up reel of a paper tape reader made by Tally circa 1962. The bevel gears spin freely on their shafts, unless a brake shoe stops the left gear. This causes the planet gear to drive the output shaft at half the speed of the driven gear on the right.
Planetary differential used to drive a chart recorder circa 1961. The motors drive the sun and annular gears, while the output is taken from the planet gear carrier. This gives 3 different speeds depending on which motors are on.

Chinese south-pointing chariots may also have been very early applications of differentials. The chariot had a pointer which constantly pointed to the south, no matter how the chariot turned as it travelled. It could therefore be used as a type of compass. It is widely thought that a differential mechanism responded to any difference between the speeds of rotation of the two wheels of the chariot, and turned the pointer appropriately. However, the mechanism was not precise enough, and, after a few miles of travel, the dial could have very well been pointing in the complete opposite direction.

The earliest definitely verified use of a differential was in a clock made by Joseph Williamson in 1720. It employed a differential to add the Equation of Time to local mean time, as determined by the clock mechanism, to produce solar time, which would have been the same as the reading of a sundial. During the 18th Century, sundials were considered to show the "correct" time, so an ordinary clock would frequently have to be readjusted, even if it worked perfectly, because of seasonal variations in the Equation of Time. Williamson's and other equation clocks showed sundial time without needing readjustment. Nowadays, we consider clocks to be "correct" and sundials usually incorrect, so many sundials carry instructions about how to use their readings to obtain clock time.

In the first half of the twentieth century, mechanical analog computers, called differential analyzers, were constructed that used differential gear trains to perform addition and subtraction. The U.S. Navy Mk.1 gun fire control computer used about 160 differentials of the bevel-gear type.

A differential gear train can be used to allow a difference between two input axles. Mills often used such gears to apply torque in the required axis. Differentials are also used in this way in watchmaking to link two separate regulating systems with the aim of averaging out errors. Greubel Forsey use a differential to link two double tourbillon systems in their Quadruple Differential Tourbillon.

## Application to vehicles

Video explaining the purpose and the principle of a differential (8 minutes, with subtitles).

A vehicle with two drive wheels has the problem that when it turns a corner the drive wheels must rotate at different speeds to maintain traction. The automotive differential is designed to drive a pair of wheels while allowing them to rotate at different speeds. In vehicles without a differential, such as karts, both driving wheels are forced to rotate at the same speed, usually on a common axle driven by a simple chain-drive mechanism.

When cornering the inner wheel travels a shorter distance than the outer wheel, so without a differential either the inner wheel rotates too fast or the outer wheel drags, which results in difficult and unpredictable handling, damage to tires and roads, and strain on (or possible failure of) the entire drivetrain.

In rear-wheel drive automobiles the central drive shaft (or prop shaft) engages the differential through a hypoid gear(crown-wheel and pinion) the crown-wheel is mounted on the carrier of the planetary chain that forms the differential. This hypoid gear is a bevel gear that changes the direction of the drive rotation.

Hypoid gear pair that connects an automotive drive shaft to a differential.

## Functional description

Input torque is applied to the ring gear (blue), which turns the entire carrier (blue). The carrier is connected to both sun gears (red and yellow) only through the planet gear (green). Torque is transmitted to the sun gears through the planet gear. The planet gear revolves around the axis of the carrier, driving the sun gears. If the resistance at both wheels is equal, the planet gear revolves without spinning about its own axis, and both wheels turn at the same rate.
If the left sun gear (red) encounters resistance, the planet gear (green) spins as well as revolving, allowing the left sun gear to slow down, with an equal speeding up of the right sun gear (yellow).

The following description of a differential applies to a "traditional" rear-wheel-drive car or truck with an "open" or limited slip differential combined with a reduction gearset using bevel gears (these are not strictly necessary - see spur-gear differential):

Thus, for example, if the car is making a turn to the right, the main crown wheel may make 10 full rotations. During that time, the left wheel will make more rotations because it has further to travel, and the right wheel will make fewer rotations as it has less distance to travel. The sun gears (which drive the axle half-shafts) will rotate in opposite directions relative to the ring gear by, say, 2 full turns each (4 full turns relative to each other), resulting in the left wheel making 12 rotations, and the right wheel making 8 rotations.

The rotation of the crown wheel gear is always the average of the rotations of the side sun gears. This is why, if the driven roadwheels are lifted clear of the ground with the engine off, and the drive shaft is held (say leaving the transmission 'in gear', preventing the ring gear from turning inside the differential), manually rotating one driven roadwheel causes the opposite roadwheel to rotate in the opposite direction by the same amount.

When the vehicle is traveling in a straight line, there will be no differential movement of the planetary system of gears other than the minute movements necessary to compensate for slight differences in wheel diameter, undulations in the road (which make for a longer or shorter wheel path), etc.

## Loss of traction

One undesirable side effect of a conventional differential is that it can limit traction under less than ideal conditions. The amount of traction required to propel the vehicle at any given moment depends on the load at that instant—how heavy the vehicle is, how much drag and friction there is, the gradient of the road, the vehicle's momentum, and so on.

The torque applied to each driving wheel is a result of the engine, transmission and drive axles applying a twisting force against the resistance of the traction at that roadwheel. In lower gears and thus at lower speeds, and unless the load is exceptionally high, the drivetrain can supply as much torque as necessary, so the limiting factor becomes the traction under each wheel. It is therefore convenient to define traction as the amount of torque that can be generated between the tire and the road surface, before the wheel starts to slip. If the torque applied to one of the drive wheels exceeds the threshold of traction, then that wheel will spin, and thus only provide torque at each other driven wheel limited by the sliding friction at the slipping wheel. The reduced net traction may still be enough to propel the vehicle.

A conventional "open" (non-locked or otherwise traction-aided) differential always supplies close to equal (because of limited internal friction) torque to each side.[6] To illustrate how this can limit torque applied to the driving wheels, imagine a simple rear-wheel drive vehicle, with one rear roadwheel on asphalt with good grip, and the other on a patch of slippery ice. It takes very little torque to spin the side on slippery ice, and because a differential splits torque equally to each side, the torque that is applied to the side that is on asphalt is limited to this amount.[7][8]

Based on the load, gradient, et cetera, the vehicle requires a certain amount of torque applied to the drive wheels to move forward. Since an open differential limits total torque applied to both drive wheels to the amount used by the lower traction wheel multiplied by a factor of 2, when one wheel is on a slippery surface, the total torque applied to the driving wheels may be lower than the minimum torque required for vehicle propulsion.[6]

A proposed way to distribute the power to the wheels, is to use the concept of gearless differential, of which a review has been reported by Provatidis,[9] but the various configurations seem to correspond either to the "sliding pins and cams" type, such as the ZF B-70 available on early VWs, or are a variation of the ball differential.

Many newer vehicles feature traction control, which partially mitigates the poor traction characteristics of an open differential by using the anti-lock braking system to limit or stop the slippage of the low traction wheel, increasing the torque that can be applied to both wheels. While not as effective in propelling a vehicle under poor traction conditions as a traction-aided differential, it is better than a simple mechanical open differential with no electronic traction assistance.

## Traction-aiding devices

ARB, air-locking differential
A cutaway drawing of a car's rear axle, showing the crown wheel and pinion of the final drive, and the smaller differential gears
A cutaway view of an automotive final drive unit which contains the differential

There are various devices for getting more usable traction from vehicles with differentials.

• The clutch-type limited slip differential (LSD), often better known as the Positraction brand is the least expensive to manufacture, and is a fairly effective modification of the stock "open" bevel gear differential. More clutch-type LSD units have been used as OEM traction aids than any other design. This modifies a standard bevel gear differential with clutch packs between the end gears and the carrier, and a preload spring that forces the side gears against the clutch packs, and the clutch packs against the differential carrier. This causes the differential to work poorly all of the time in order to give greater traction in some circumstances. This is a compromise device that performs neither of its intended functions well. In rear wheel drive applications on slippery surfaces such as wet or icy roads, the coefficient of friction of the clutch packs will often exceed the coefficient of friction between the tires and the road, causing both drive wheels to spin and leading to loss of control, especially in turns. In front wheel drive or front axle of 4x4 vehicles, the inhibited differential will cause the axles to "wind up" in turns, affecting steering, and leading to loss of control. Clutch packs will wear out over time, causing the loss of traction aid and the possibility of differential failure if clutch parts break off and get into the gears.
• Auburn Gear makes a cone-style limited slip differential that dispenses with the clutch packs, and uses the outside surfaces of the side gears and the differential case as the friction materials. This type of LSD is functionally identical to the clutch-type, but purports to last longer before needing service. If it does need service, it must be returned to the factory however.
• Centrifugal weights can be used in conjunction with, or in place of the preload spring(s) to force the side gears into the carrier. The Eaton G80 (sold by General Motors under the Gov-Lok name) is one example of this. In theory the centrifugal action should offer a more progressive application of torque bias, and therefore fewer undesirable side-effects. The added complexity can cause premature failure under heavy use.
• A locking differential typified by the Detroit Locker (now an Eaton brand) is not a differential at all. In place of the differential is a pair of dog clutches and preload springs that force the two drive axles to "lock up" with the case (typically this type uses the case of a standard open differential, replacing the differential gears) while driving in a straight line. During cornering, one of the dog clutches should disengage, causing one side to freewheel. In practice the unlocking can be problematic and erratic.
• Remote locking differentials are normal differentials fitted with a mechanism to lock the differential (and therefore stop all differential action) using air or electromagnetic actuators that can be engaged or released on demand by the driver. When locked, they allow no difference in speed between the two wheels on the axle. They employ a mechanism for allowing the axles to be locked relative to each other, causing both wheels to turn at the same speed regardless of which has more traction; this is equivalent to effectively bypassing the differential gears entirely. Devices like this have been used on heavy trucks for a very long time. In recent years smaller models have been developed for light trucks and passenger cars. In light trucks, the locking function can be engaged for off-road use, and disengaged for a safe ride on the road. For cars the locking function is typically used for drag racing regardless of the location.
• A worm and spur gear differential, such as the Torsen differential, uses the friction is between the gear teeth rather than at added clutches. It is a relatively new and completely unique differential design that has torque bias as a standard function. This type of differential applies more torque to the driven wheel with highest resistance (grip or traction) when the limit of friction is reached at that other wheel. Under normal conditions it behaves exactly like an open differential. In cases where both driven wheels are spinning, the Torsen automatically balances the torque instantly, creating a stable and safe ride. Transitions between slick and grippy surfaces cause no instability, unlike other limited slip and locking traction adders that lock both drive wheels together by default. When tested with the wheels off the ground, if one wheel is rotated with the differential case held, the other wheel will still rotate in the opposite direction as for an open differential but there will be some frictional losses and the torque will be distributed at other than 50/50. Although named as being "torque-sensing", it actually distinguishes itself by providing torque bias in proportion to available grip. 3D Animation of a Torsen Differential
• A very high-friction differential, such as the ZF "sliding pins and cams" type, so that there is locking from very high internal friction. When tested with the wheels off the ground with torque applied to one wheel it will lock, but it is still possible for the differential action to occur in use, albeit with considerable frictional losses, and with the road loads at each wheel in opposite directions rather than the same (acting with a "locking and releasing" action rather than a distributed torque). This 1935 design was possibly the first attempt at improving an open differential for increased power delivery.
• Electronic traction control systems usually use the anti-lock braking system (ABS) speed sensors to detect a spinning roadwheel, and apply the brake to that wheel. This progressively raises the reaction torque at that roadwheel, and the differential compensates by transmitting more torque through the other roadwheel—the one with better traction. In Volkswagen Group vehicles, this specific function is called 'Electronic Differential Lock' (EDL).
• A spool is a solid 1-piece part that completely replaces the differential and its case. A variant called "mini-spool" replaces the differential gears within the differential carrier, retaining the stock carrier. A spool locks both axle shafts together 100%. With both wheels turning at exactly the same rate, the burden for providing maximum traction falls upon the surface driven on. The primary advantage to a spool is, contrary to popular belief, not maximum traction but maximum simplicity. Spools are often used in drag racing applications, where the vehicle is to be driven in a straight line while applying tremendous torque to both wheels, and where the track is specially prepared for even traction.
• In a four-wheel drive vehicle, a viscous coupling unit can replace a centre differential entirely, or be used to limit slip in a conventional 'open' differential. It works on the principle of allowing the two output shafts to counter-rotate relative to each other, by way of a system of slotted plates that operate within a viscous fluid, often silicone. The fluid allows slow relative movements of the shafts, such as those caused by cornering, but will strongly resist high-speed movements, such as those caused by a single wheel spinning. This system is similar to a limited slip differential.

A four-wheel drive (4WD) vehicle will have at least two differentials (one in each axle for each pair of driven roadwheels), and possibly a centre differential to apportion torque between the front and rear axles. In some cases (e.g. Lancia Delta Integrale, Porsche 964 Carrera 4 of 1989[10]) the centre differential is an epicyclic differential (see below) to divide the torque asymmetrically, but at a fixed rate between the front and rear axle. Other methods utilise an 'Automatic Torque Biasing' (ATB) centre differential, such as a Torsen—which is what Audi use in their quattro cars (with longitudinal engines).

Some 4WD vehicles without a centre differential or transfer case should not be driven on dry, paved roads in four-wheel drive mode, as small differences in rotational speed between the front and rear wheels cause a torque to be applied across the transmission. This phenomenon is known as "wind-up", and can cause considerable damage to the transmission or drive train. On loose surfaces these differences are absorbed by the tire slippage on the road surface.

A transfer case typically incorporates a centre differential, allowing the drive shafts to spin at different speeds. This permits the four-wheel drive vehicle to drive on paved surfaces without experiencing "wind-up". Notable exceptions include BorgWarner Torque-On-Demand transfer cases that use an electronically controlled clutch to proportion between 0% to 50% of power to the front wheels as needed. Ford's AdvanceTrac system operates the TOD transfer case and brakes to send up to 100% of engine power to any one wheel.

## Active differentials

A relatively new technology is the electronically controlled 'active differential'. An electronic control unit (ECU) uses inputs from multiple sensors, including yaw rate, steering input angle, and lateral acceleration—and adjusts the distribution of torque to compensate for undesirable handling behaviours like understeer. Active differentials used to play a large role in the World Rally Championship, but in the 2006 season the FIA has limited the use of active differentials only to those drivers who have not competed in the World Rally Championship in the last five years.

Fully integrated active differentials are used on the Ferrari F430, Mitsubishi Lancer Evolution, and on the rear wheels in the Acura RL. A version manufactured by ZF is also being offered on the B8 chassis Audi S4 and Audi A4.[11] The Volkswagen Golf GTI Mk7 in Performance trim also has an electronically controlled front-axle transverse differential lock, also known as VAQ.[12]

The second constraint of the differential is passive—it is actuated by the friction kinematics chain through the ground. The difference in torque on the roadwheels and tires (caused by turns or bumpy ground) drives the second degree of freedom, (overcoming the torque of inner friction) to equalise the driving torque on the tires. The sensitivity of the differential depends on the inner friction through the second degree of freedom. All of the differentials (so called "active" and "passive") use clutches and brakes for restricting the second degree of freedom, so all suffer from the same disadvantage—decreased sensitivity to a dynamically changing environment. The sensitivity of the ECU controlled differential is also limited by the time delay caused by sensors and the response time of the actuators.

## Automobiles without differentials

Although most automobiles in the developed world use differentials there are a few that do not. Several different types exist:

• Race cars and trucks in certain classes. Drag racing is done in a straight line (and often on a prepared surface), which obviates the need for a differential. A spool is used to make a solid connection between both drive wheels, which is simpler and less likely to break under very heavy acceleration. Racing on dirt or mud tracks also allows the use of spools, because the loose surface gives way while cornering. NASCAR mandates the use of spools in their cars, which does cause axle wind-up, and degrades handling in turns. Other forms of racing without differentials includes tractor pulling, mud bogging and other 4x4 motorsports where differential action is not needed.
• Vehicles with a single driving wheel. Besides motorcycles, which are generally not classified as automobiles, this group includes most three-wheeled cars. These were quite common in Europe in the mid-20th Century, but have now become rare there. They are still common in some areas of the developing world, such as India. Some early four-wheeled cars also had only one driving wheel to avoid the need for a differential. However, this arrangement led to many problems. The system was unbalanced, the driving wheel would easily spin, etc.. Because of these problems, few such vehicles were made.
• Vehicles using two freewheels. A freewheel, as used on a pedal bicycle for example, allows a road wheel to rotate faster than the mechanism that drives it, allowing a cyclist to stop pedalling while going downhill. Some early automobiles had the engine driving two freewheels, one for each driving road wheel. When the vehicle turned, the engine would continue to drive the wheel on the inside of the curve, but the wheel on the outside was permitted to rotate faster by its freewheel. Thus, while turning, the vehicle had only one driving wheel. Driving in reverse is also impossible as is engine braking due to the freewheels.
• Vehicles with continuously variable transmissions, such as the DAF Daffodil. The Daffodil, and other similar vehicles which were made until the 1970s by the Dutch company DAF, had a type of transmission that used an arrangement of belts and pulleys to provide an infinite number of gear ratios. The engine drove two separate transmissions which ran the two driving wheels. When the vehicle turned, the two wheels could rotate at different speeds, making the two transmissions shift to different gear ratios, thus functionally substituting for a differential. The slower moving wheel received more driving torque than the faster one, so the system had limited-slip characteristics. The duplication also provided redundancy. If one belt broke, the vehicle could still be driven.
• Light vehicles with closely spaced rear wheels, such as the Isetta and Opperman Unicar, or very low mass vehicles.
• Vehicles with separate motors for the driving wheels. Electric cars can have a separate motor for each driving wheel, eliminating the need for a differential, but usually with some form of gearing at each motor to get the large wheel torques necessary. A multi-motor electric vehicle such as the Dual Motor Tesla Model S can electronically control the power distribution between the motors on a millisecond scale, effectively an electronic differential.[13] Hybrid vehicles in which the final drive is electric can be configured similarly.

## References and footnotes

1. ^ a b Wright, M. T. (2007). "The Antikythera Mechanism reconsidered" (PDF). Interdisciplinary science reviews 32 (1). Retrieved 20 May 2014.
2. ^ Presentation given to the NHRF in Athens, 6 March 2007 - M. T. Wright
3. ^ "History of the Automobile". Gmcanada.com. Retrieved 2011-01-09.
4. ^ Preston, J.M. (1987), Aveling & Porter, Ltd. Rochester., North Kent Books, pp. 13–14, ISBN 0-948305-03-7 includes sectional drawing.
5. ^ J. J. Uicker, G. R. Pennock and J. E. Shigley, 2003, Theory of Machines and Mechanisms, Oxford University Press, New York.
6. ^ a b Chocholek, S. E. (1988) "The development of a differential for the improvement of traction control"
7. ^ Bonnick, Allan. (2001) "Automotive Computer Controlled Systems p. 22
8. ^ Bonnick, Allan. (2008). "Automotive Science and Mathematics p. 123
9. ^ Provatidis, Christopher, G. (2003). "A critical presentation of Tsiriggakis’ gearless differential". Mobility & Vehicles Mechanics 29 (4): 25–46; also: http://users.ntua.gr/cprovat/index_en.htm
10. ^ "The Complete Story of Porsche 911". Autozine.org. Retrieved 2011-01-09.
11. ^ "ZF Press release". Zf.com. Retrieved 2011-01-09.
12. ^ "Golf VII GTI". pistonheads.com. Retrieved 2013-06-24.
13. ^ Davies, Alex (2014-10-10). "The Model D Is Tesla’s Most Powerful Car Ever, Plus Autopilot". Wired.com. Retrieved 2014-10-11. Musk said the added efficiency is thanks to the electronic system that will shift power between the front and rear motors from one millisecond to the next, so each is always operating at its most efficient point