Emergency position-indicating radiobeacon station
An Emergency Position-Indicating Radiobeacon Station or Emergency Position Indicator Radio Beacon (short: EPIRS or EPIRB) is a station in the mobile service used in search and rescue operations. In marine use the terminology Emergency Position Indicating Radio Beacon (EPIRB) is used.
- 1 General description
- 2 Operation
- 3 Beacon modes
- 4 Frequency
- 5 Types
- 6 Phase-out of 121.5 & 243 beacons
- 7 Statutory requirements
- 8 Environment-specific requirements
- 9 History
- 10 Current events
- 11 Alternative technologies
- 12 See also
- 13 Notes
- 14 References
- 15 External links
EPIRBs are tracking transmitters which aid in the detection and location of boats, aircraft, and people in distress. A PLB (personal locator beacon) is particular type of EPIRB that is typically smaller, has a shorter battery life and unlike a proper EPIRB is registered to a person rather than a vessel. The terms ELB (emergency locator beacon) and ELT (emergency locator transmitter) are used interchangeably with EPIRB only when used on aircraft. Strictly, they are radiobeacons many of which interface with worldwide offered service of Cospas-Sarsat, the international satellite system for search and rescue (SAR). Transmitters broadcasting on 406 MHz are recognized. When manually activated, or automatically activated upon immersion or impact, such beacons send out a distress signal. The signals are monitored worldwide and the location of the distress is detected by non-geostationary satellites using the doppler effect for trilateration, and in more recent EPIRBs also by GPS.
The basic purpose of a distress radiobeacon is to help rescuers find survivors within the so-called "golden day" (the first 24 hours following a traumatic event) during which the majority of survivors can usually be saved.
Since the inception of Cospas-Sarsat in 1982, distress radiobeacons have assisted in the rescue of over 28,000 people in more than 7,000 distress situations. In 2010 alone, the system provided information which was used to rescue 2,388 persons in 641 distress situations.
Most beacons are brightly colored and waterproof. EPIRBs and ELTs are larger, and would fit in a cube about 30 cm (12 in) on a side, and weigh 2 to 5 kg (4.4 to 11.0 lb). PLBs vary in size from cigarette-packet to paperback book and weigh 200 g to 1 kg (½ to 2½ lb). They can be purchased from marine suppliers, aircraft refitters, and (in Australia and the United States) hiking supply stores. The units have a useful life of 10 years, operate across a range of conditions −40 to 40 °C (−40 to 104 °F), and transmit for 24 to 48 hours. The cost of radiobeacons varies according to performance and specifications.
A transmission usually gets processed as follows:
- The transmitter is activated, either automatically in a crash or after sinking, or manually by survivors of an emergency situation.
- At least one satellite picks up the beacon's transmission.
- The satellites transfer the beacon's signal to their respective ground control stations.
- The ground stations process the signals and forward the data, including approximate location, to a national authority.
- The national authority forwards the data to a rescue authority
- The rescue authority uses its own receiving equipment afterwards to locate the beacon and commence its own rescue or recovery operations.
Once the satellite data is received, it takes less than a minute to forward it to any signatory nation.
There are several systems in use, with beacons of varying expense, different types of satellites and varying performance. Carrying even the oldest systems provides an immense improvement in safety over carrying none.
There are two ways to activate a beacon:
Automatic EPIRBs are water activated, while automatic ELTs have impact monitors activated by g-force. Some EPIRBs also "deploy"; this means that they physically depart from their mounting bracket on the exterior of the vessel (usually by going into the water.)
For a marine EPIRB to begin transmitting a signal (or "activate") it first needs to come out of its bracket (or "deploy"). Deployment can happen either manually where someone must physically remove it from its bracket or automatically where water pressure will cause a hydrostatic release unit to separate the EPIRB from its bracket. If it does not come out of the bracket it will not activate. There is a magnet in the bracket which operates a reed safety switch in the EPIRB. This prevents accidental activation if the unit gets wet from rain or shipped seas.
Once deployed, EPIRBs can be activated, depending on the circumstances, either manually (crewman flicks a switch) or automatically (when water contacts the unit's "sea-switch".) All modern EPIRBs provide both methods of activation and deployment, and thus are labelled "Manual and Automatic Deployment and Activation."
Automatic hydrostatic release unit
A hydrostatic release unit or HRU is a pressure activated mechanism designed to automatically deploy when certain conditions are met. In the marine environment this occurs when submerged to a maximum depth of four meters. The pressure of the water against a diaphragm within the sealed casing causes a plastic pin to be cut thereby releasing the containment bracket casing, allowing the EPIRB to float free.
Some common characteristics of HRUs are:
- Water pressure sensitive at depths not to exceed four meters or less than two meters
- Single use only, require replacement if activated
- Cannot be serviced; only replaced
- Waterproof; sealed against moisture and tampering
- Must be labeled with expiration date
- Expiration date is two years from month of installation applies to unit and rod
Several regulations and technical specifications govern EPIRB Hydrostatic Release Devices:
- Corrosion Resistance Test
- Temperature Tests
- Submergence and Manual Release Test
- Strength Tests
- Technical Tests on the Membrane
- Performance Test
The most modern 406 MHz beacons with GPS (US$300+ in 2010) track with a precision of 100 meters in the 70% of the world closest to the equator, and send a serial number so the responsible authority can look up phone numbers to notify the registrator (e.g., next-of-kin) in four minutes.
The GPS system permits stationary, wide-view geosynchronous communications satellites to enhance the doppler position received by low Earth orbit satellites. EPIRB beacons with built-in GPS are usually called GPIRBs, for GPS position-indicating radio beacon or global position-indicating radio beacon.
However, rescue cannot begin until a doppler track is available. The COSPAS-SARSAT specifications say  that a beacon location is not considered "resolved" unless at least two doppler tracks match or a doppler track confirms an encoded (GPS) track. One or more GPS tracks are not sufficient.
An intermediate technology 406 MHz beacon (now mostly obsolete in favor of GPS enabled units) has worldwide coverage, locates within 2 km (12.5 km² search area), notifies kin and rescuers in 2 hours maximum (46 min average), and has a serial number to look up phone numbers, etc. This can take up to two hours because it has to use moving weather satellites to locate the beacon. To help locate the beacon, the beacon's frequency is controlled to 2 parts per billion, and its power is five watts.
Both of the above types of beacons usually include an auxiliary 25 milliwatt beacon at 121.5 MHz to guide rescue aircraft.
Traditional ELT, unregistered
The oldest, cheapest (US$139) beacons are aircraft emergency locator transmitters (ELTs) that send an anonymous warble on the aviation band distress frequency at 121.5 MHz. The frequency is often routinely monitored by commercial aircraft, but has not been monitored by satellite since Feb. 1, 2009.
These distress signals could be detected by satellite over only 60% of the earth, required up to 6 hours for notification, located within 20 km (12 mi) (search area of 1200 km²), were anonymous, and couldn't be located well because their frequency is only accurate to 50 parts per million and the signals were broadcast using only 75–100 milliwatts of power. Coverage was partial because the satellite had to be in view of both the beacon and a ground station at the same time – the satellites did not store and forward the beacon's position. Coverage in polar and south-hemisphere areas was poor.
False alarms were common, as the beacon transmitted on the aviation emergency frequency, and there is interference from other electronic and electrical systems. To reduce false alarms, a beacon was confirmed by a second satellite pass, which could easily slow confirmation of a 'case' of distress to up to about 4 hours (although in rare circumstances the satellites could be position such that immediate detection becomes possible.)
Location by Doppler (without GPS)
The Cospas-Sarsat system was made possible by Doppler processing. Local unit terminals (LUTs) detecting non-geostationary satellites interpret the Doppler frequency shift heard by LEOSAR and MEOSAR satellites as they pass over a beacon transmitting at a fixed frequency. The interpretation determines both bearing and range. The range and bearing are measured from the rate of change of the heard frequency, which varies both according to the path of the satellite in space and the rotation of the earth. This triangulates the position of the beacon. A faster change in the doppler indicates that the beacon is closer to the satellite's orbit. If the beacon is moving toward or away from the satellite track due to the Earth's rotation, it is on one side or other of the satellite's path. Doppler shift is zero at the closest point of approach between the beacon and the orbit.
If the beacon's frequency is more precise, it can be located more precisely, saving search time, so modern 406 MHz beacons are accurate to 2 parts per billion, giving a search area of only 2 square km, compared to the older beacons accurate to 50 parts per million that had 200 square kilometers of search area.
In order to increase the useful power, and handle multiple simultaneous beacons, modern 406 MHz beacons transmit in bursts, and remain silent for about 50 seconds.
Russia developed the original system, and its success drove the desire to develop the improved 406 MHz system. The original system was a brilliant adaptation to the low quality beacons, originally designed to aid air searches. It used just a simple, lightweight transponder on the satellite, with no digital recorders or other complexities. Ground stations listened to each satellite as long as it was above the horizon. Doppler shift was used to locate the beacon(s). Multiple beacons were separated when a computer program analysed the signals with a fast fourier transform. Also, two satellite passes per beacon were used. This eliminated false alarms by using two measurements to verify the beacon's location from two different bearings. This prevented false alarms from VHF channels that affected a single satellite. Regrettably, the second satellite pass almost doubled the average time before notification of the rescuing authority. However, the notification time was much less than a day.
Receivers are auxiliary systems mounted on several types of satellites. This substantially reduces the program's cost.
The weather satellites that carry the SARSAT receivers are in "ball of yarn" orbits, inclined at 99 degrees. The longest period that all satellites can be out of line-of-sight of a beacon is about two hours.
The first satellite constellation was launched in the early 1970s by the Soviet Union, Canada, France and the United States.
Some geosynchronous satellites have beacon receivers. Since the end of 2003, there are four such geostationary satellites (GEOSAR) that cover more than 80% of the surface of the earth. As with all geosynchronous satellites, they are located above the equator. The GEOSAR satellites do not cover the polar caps.
Since they see the Earth as a whole, they see the beacon immediately, but have no motion, and thus no doppler frequency shift to locate it. However, if the beacon transmits GPS data, the geosynchronous satellites give nearly instantaneous response.
Search and Rescue response
Emergency beacons operating on 406 MHz transmit a unique 15, 22, or 30 character serial number called a Hex Code. When the beacon is purchased, the Hex Code should be registered with the relevant national (or international) authority. Registration provides Search and Rescue agencies with crucial information such as:
- phone numbers to call,
- a description of the vessel, aircraft, vehicle, or person (in the case of a PLB)
- the home port of a vessel or aircraft
- any additional information that may be useful to SAR agencies
Registration information allows SAR agencies to start a rescue more quickly. For example, if a shipboard telephone number listed in the registration is unreachable, it could be assumed that a real distress event is occurring. Conversely, the information provides a quick and easy way for the SAR agencies to check and eliminate false alarms (potentially sparing the beacon's owner from significant false alert fines.)
An unregistered 406 beacon still carries some information, such as the manufacturer and serial number of the beacon, and in some cases, an MMSI or aircraft tail number/ICAO 24-bit address. Despite the clear benefits of registration, an unregistered 406 beacon is very substantially better than a 121.5/243.0 beacon; this is because the Hex Code received from a 406 beacon confirms the authenticity of the signal as a real SAR alert.
Transmission of a distress radiobeacon on 121.5 MHz and 243 MHz
|Problems playing this file? See media help.|
Beacons operating on 121.5 and 243.0 MHz only simply transmit an anonymous siren tone, and thus carry no information to SAR agencies. Such beacons now rely solely on the terrestrial or aeronautical monitoring of the frequency. In the UK, the Distress and Diversion Cell of the Royal Air Force provides continuous monitoring of 121.5 and 243.0 MHz, with autotriangulation from a network of terrestrial receivers on both frequencies. In Canada, only air traffic service stations (control towers or flight service facilities) monitor 121.5 MHz during operating hours. Overflying commercial or private aircraft monitor 121.5 MHz only if equipped with a suitable receiver, and if time/courtesy permits; monitoring 121.5 MHz is not mandatory. SAR authorities have no way of knowing whether a 121.5/243.0 MHz signal is actually a SAR signal until they physically deploy to the location and home in on the source (and sound) of the transmission. Since SAR resources are scarce (and expensive), most countries do not deploy the most useful SAR homing assets (aircraft) until ambiguity has been resolved (see doppler).
According to the U.S. Federal Aviation Administration, ground testing of A-, B-, and S-type ELTs is to be done within the first 5 minutes of each hour. Testing is restricted to three audio sweeps. Type I and II devices (those transmitting at 406 MHz) have a self test function and must not be activated except in an actual emergency.
The United States Coast Guard web page for EPIRBs states: "You may be fined for false activation of an unregistered EPIRB. The U.S. Coast Guard routinely refers cases involving the non-distress activation of an EPIRB (e.g., as a hoax, through gross negligence, carelessness or improper storage and handling) to the Federal Communications Commission. The FCC will prosecute cases based upon evidence provided by the Coast Guard, and will issue warning letters or notices of apparent liability for fines up to $10,000."
The most important aspect of a beacon in classification is the mode of transmission. There are two valid transmission modes: digital and analog. Where digital usually has a longer range, analog is more reliable. Analog beacons are useful to search parties and SAR aircraft, though they are no longer monitored by satellite.
Digital mode: 406 MHz beacons
406 MHz beacons transmit bursts of digital information to orbiting satellites, and may also contain a small integrated analog (121.5 MHz) homing beacon. They can be uniquely identified (via GEOSAR). Advanced beacons encode a GPS or GLONASS position into the signal. All beacons are located by doppler triangulation to confirm the location. The digital data identifies the registered user. A phone call by authorities to the registered phone number often eliminates false alarms (false alarms are the typical case). If there is a problem, the beacon location data guides search and rescue efforts. No beacon is ignored. Anonymous beacons are confirmed by two doppler tracks before beginning beacon location efforts.
The distress message transmitted by a 406 beacon contains the information such as:
- Which country the beacon originates from.
- A unique 15-digit hexadecimal beacon identification code (a "15-hex ID").
- The encoded identification of the vessel or aircraft in distress, either as an MMSI value, or as, in the case of an ELT, either the aircraft's registration or its ICAO 24-bit address (from its Mode-S transponder).
- When equipped, a GPS position.
- Whether or not the beacon contains a 121.5 MHz homing transmitter.
The digital distress message generated by the beacon varies according to the above factors and is encoded in 30 hexadecimal characters. The unique 15-character digital identity (the 15-hex ID) is hard-coded in the firmware of the beacon. The 406.025 MHz carrier signal is modulated plus or minus 1.1 radians with the data encoded using Manchester encoding, which ensures a net zero phase shift aiding Doppler location 
406 MHz beacon facts and transmission schedule
- 406 MHz beacons transmit for a quarter of a second immediately when turned on, and then transmit a digital burst once every 50 seconds thereafter. Both GEOSAR and LEOSAR satellites monitor these signals.
- The repetition period shall not be so stable that any two transmitters appear to be synchronized closer than a few seconds over a 5-minute period. The intent is that no two beacons will have all of their bursts coincident. The period shall be randomised around a mean value of 50 seconds, so that time intervals between transmission are randomly distributed on the interval 47.5 to 52.5 seconds. (specification for First-Generation beacons) 
- Preliminary Specification for Second-Generation Beacons. From beacon activation a total of  initial transmissions shall be made separated by fixed [5s ± 0.1s] intervals. The first transmission shall commence within  seconds of beacon activation. Transmissions shall then occur at nominally  second intervals until [30 ± 1] minutes after beacon activation. The repetition period between the start of two successive transmissions shall be randomised around the stated nominal value, so that intervals between successive transmissions are randomly distributed over ±  seconds. Subsequent transmissions [TBD].
- 406 MHz beacons will be the only beacons compatible with the MEOSAR (DASS) system.
- 406 MHz beacons must be registered (see below).
Example hex codes look like the following: 90127B92922BC022FF103504422535 
- A bit telling whether the message is short (15 hex digits) or long (30 hex digits) format.
- A country code, which lets the worldwide COSPAS/SARSAT central authority identify the national authority responsible for the beacon.
- Embedded 15-Hex ID or 15-hex transmitted distress message, for example, 2024F72524FFBFF The hex ID is printed or stamped on the outside of the beacon and is hard-coded into its firmware. The 15-hex ID can only be reprogrammed by certified distress radiobeacon technicians. The national authority uses this number to look up phone numbers and other contact information for the beacon. This is crucial to handle the large number of false alarms generated by beacons.
- A location protocol number, and type of location protocol: EPIRB or MMSI, as well as all the data fields of that location protocol. If the beacon is equipped with GPS or GLONASS, a rough (rounded) latitude and longitude giving the beacon's current position. In some aircraft beacons, this data is taken from the aircraft's navigation system.
- When a beacon is sold to another country, the purchaser is responsible for having the beacon reprogrammed with a new country code and to register it with his/her nation's beacon registry, and the seller is responsible to de-register the deprecated beacon ID with his/her national beacon registry.
- One can use the beacon decoder web page at Cospas-Sarsat to extract the 15-hex ID from the 30-hex distress message.
These devices are distinct from traditional SAR radar transponders (SART), as they transmit AIS messages containing accurate GPS position information and include a GPS receiver and a transmitter on VHF AIS channels, so they show up on ship AIS receivers. They are lightweight and can be used to equip inflatable liferafts.
Analog mode: all other beacons
- A simple analog siren tone is transmitted continuously until the battery dies.
- In the case of 121.5 MHz beacons, the frequency is known in aviation as the "VHF Guard" emergency frequency, and all U.S. civilian pilots (private and commercial) are required, by FAA policy, to monitor this frequency when it is possible to do so. The frequency can be used by Automatic Direction Finder (ADF) radionavigation equipment, which is being phased out in favor of VOR and GPS but is still found on many aircraft.
- The Cospas-Sarsat system detected this type of beacon – prior to 1 February 2009 – when a LEOSAR satellite was in view of both the beacon and a LEOLUT (ground segment). Satellite detection of 121.5 MHz beacons ceased on 1 February 2009 (see below).
Distress beacons transmit distress signals on the following key frequencies; the frequency used distinguishes the capabilities of the beacon. A recognized beacon can operate on one of the three (currently) Cospas-Sarsat satellite-compatible frequencies. In the past, other frequencies were also used as a part of the search and rescue system.
Cospas-Sarsat (satellite) compatible beacon frequencies
- see above for transmission schedule
- 406 MHz UHF- carrier signal at 406.025-406.076 MHz ± 0.005 MHz
- Ch-1 A: 406.022 MHz (reference)
- Ch-2 B: 406.025 MHz (in use today)
- Ch-3 C: 406.028 MHz (in use today)
- Ch-4 D: 406.031 MHz
- Ch-5 E: 406.034 MHz
- Ch-6 F: 406.037 MHz (in use today)
- Ch-7 G: 406.040 MHz (in use today)
- Ch-8 H: 406.043 MHz
- Ch-9 I: 406.046 MHz
- Ch-10 J: 406.049 MHz (operational at a future date)
- Ch-11 K: 406.052 MHz (operational at a future date)
- Ch-12 L: 406.055 MHz
- Ch-13 M: 406.058 MHz
- Ch-14 N: 406.061 MHz (operational at a future date)
- Ch-15 O: 406.064 MHz (operational at a future date)
- Ch-16 P: 406.067 MHz
- Ch-17 Q: 406.070 MHz
- Ch-18 R: 406.073 MHz (operational at a future date)
- Ch-19 S: 406.076 MHz (operational at a future date)
Cospas-Sarsat incompatible beacon frequencies
- Marine VHF radio channels 15/16 – these channels are used only on the obsolete Class C EPIRBs
- The obsolete Inmarsat-E beacons transmitted to Inmarsat satellites on 1646 MHz UHF.
- 121.5 MHz VHF ± 6 kHz (frequency band protected to ±50 kHz) (Satellite detection ceased on 1 February 2009, but this frequency is still used for short-range location during a search and rescue operation)
- 243.0 MHz UHF ± 12 kHz (frequency band protected to ± 100 kHz) (prior to 1 February 2009 – COSPAS-SARSAT Compatible)
The type of a beacon is determined by the environment for which it was designed to be used:
- EPIRBs (emergency position indicating radio beacons) signal maritime distress,
- ELTs (emergency locator transmitters) signal aircraft distress
- PLBs (personal locator beacons) are for personal use and are intended to indicate a person in distress who is away from normal emergency services; e.g., 9-1-1. They are also used for crewsaving applications in shipping and lifeboats at terrestrial systems. In New South Wales, some police stations and the National Parks and Wildlife Service provide personal locator beacons to hikers for no charge.
Each type is sub-classified:
Emergency position-indicating radio beacons (EPIRBs) are sub-classified as follows:
- Category I – 406/121.5 MHz. Float-free, automatically activated EPIRB. Detectable by satellite anywhere in the world. Recognized by GMDSS.
- Category II – 406/121.5 MHz. Similar to Category I, except is manually activated. Some models are also water activated.
- Class A – 121.5/243 MHz. Float-free, automatically activating. These devices have been phased out by the U.S. Federal Communications Commission (FCC) and are no longer recognized.
- Class B – 121.5/243 MHz. Manually activated version of Class A. These devices have been phased out by the FCC and are no longer recognized.
- Class S – 121.5/243 MHz. Similar to Class B, except it floats, or is an integral part of a survival craft (lifeboat). These devices have been phased out by the FCC and are no longer recognized.
- Class C – Marine VHF ch15/16. Manually activated, these beacons operate on maritime channels only, and therefore are not detectable by satellite or normal aircraft. These devices have been phased out by the FCC and are no longer recognized.
- Inmarsat-E – This service ended 1 December 2006; all former users have switched to Category I or II 406 MHz EPIRBs. These beacons were float-free, automatically activated EPIRBs operated on 1646 MHz. They were detectable by Inmarsat geostationary satellites, and were recognized by GMDSS. See Inmarsat-E.
Emergency locator transmitters (ELTs) for aircraft may be classed as follows:
- A ELT, automatically ejected
- AD ELT, automatic deployable
- F ELT, Fixed
- AF ELT, automatic fixed
- AP ELT, automatic portable
- W ELT, water activated
- S ELT, survival
Within these classes, an ELT may be either a digital 406 MHz beacon, or an analog beacon (see above).
There are two kinds of personal locator beacon (PLB):
- PLB with GPS data (internally or externally provided)
- PLB with no GPS data
All PLBs transmit in digital mode on 406 MHz. There are AIS PLBs that transmit on VHF 70
There are also several older types of EPIRB devices which are no longer recommended for use.
- Class A – A 121.5 MHz automatic activation unit. Due to limited signal coverage and possible lengthy delays in signal recognition, the U.S. Coast Guard no longer recommends use of this type.
- Class C – Operates on VHF channel 15/16. Designed for small crafts operating close to shore, this type was only recognized in the United States. Use of these units was phased out in 1999.
- Class S – A 121.5 MHz unit similar to Class B but is often included as an integral part of a lifeboat or survival suit. Their use is no longer recommended by the U.S. Coast Guard.
- Inmarsat E – entered service in 1997. The unit is an automatic activation unit operating on 1646 MHz and detectable by the Inmarsat geostationary satellite system. This class of EPIRB was approved by the Global Maritime Distress and Safety System (GMDSS), but not by the United States. In September 2004, Inmarsat announced that it was terminating its Inmarsat E EPIRB service as of December 2006 due to a lack of interest in the maritime community.
Furthermore, the U.S. Coast Guard recommend that no EPIRB of any type manufactured before 1989 be used.
- Any ELT that is not a 406 MHz ELT with a Hex Code became obsolete February 1, 2009.
- Military forces at one time used 121.5/243.0 MHz beacons such as the "PRC-106," which had a built-in VHF radio. These are being replaced[by whom?] by modern 406 MHz PLBs.
Phase-out of 121.5 & 243 beacons
Since 1 February 2009, only 406 MHz beacons are detected by the international Cospas-Sarsat SAR satellite system. This affects all maritime beacons (EPIRBs), all aviation beacons (ELTs) and all personal beacons (PLBs). In other words, Cospas-Sarsat has ceased satellite detection and processing of 121.5/243 MHz beacons. These older beacons are now only detectable by ground-based receivers and aircraft.
121.5 and 243.0 MHz EPIRBs are banned on boats in the United States and in many other jurisdictions. More information about the switch to 406 is available on Cospas-Sarsat's 121.5/243 Phase-Out page.
Despite the switch to 406 MHz, pilots and ground stations are encouraged to continue to monitor for transmissions on the emergency frequencies, as many 406 beacons are also equipped with 121.5 "homers." Furthermore, the 121.5 MHz frequency continues to be used as a voice distress frequency (especially in aviation).
In North America and Australasia (and most jurisdictions in Europe) no special license is required to operate an EPIRB. In some countries (for example the Netherlands) a marine radio operators license is required. The following paragraphs define other requirements relating to EPIRBs, ELTs, and PLBs.
All distress alerting beacons operating on 406 MHz should be registered; all vessels and aircraft operating under International Convention for the Safety of Life at Sea (SOLAS) and International Civil Aviation Organization (ICAO) regulations must register their beacons. Some national administrations (including the United States, Canada, Australia, and the UK) also require registration of 406 MHz beacons.
- There is no charge to register 406 MHz beacons.
- The U.S. Coast Guard warns that a user's "life may be saved as a result of registered emergency information" because it can respond more quickly to signals from registered beacons.
- Unless the national registry authority advises otherwise, personal information contained in a beacon is used exclusively for SAR distress alert resolution purposes.
The Cospas-Sarsat Handbook of Beacon Regulations provides the status of 406 MHz beacon regulations in specific countries and extracts of some international regulations pertaining to 406 MHz beacons.
The following list shows the agencies accepting 406 beacon registrations by country:
- United States – National Oceanic and Atmospheric Administration
- Canada – Canadian Beacon Registry, CFB Trenton for civil beacons, CMCC for military beacons
- Australia – Australian Maritime Safety Authority (AMSA)
- United Kingdom – United Kingdom Maritime and Coastguard Agency (MCA)
- Greece – Ministry of Merchant Marine and Hellenic Civil Aviation Authority
- France – CNES
- Italy – Stazione Satellitare Italiana - Cospas Sarsat
- Netherlands – Agentschap Telecom (NL)
- Denmark - Danish Maritime Authority
- New Zealand - New Zealand Rescue Coordination Centre 
- International – Cospas-Sarsat International 406 MHz Beacon Registration Database (IBRD)
||The examples and perspective in this section deal primarily with USA and do not represent a worldwide view of the subject. (September 2012) (Learn how and when to remove this template message)|
In the U.S. the Coast Guard investigates offshore beacons and rescues victims. On-shore beacons are investigated by local search-and-rescue services in Alaska. The Air Force Rescue Coordination Center responds to land-based emergency signals, usually dispatching volunteer members from the United States Air Force Auxiliary Civil Air Patrol. In the U.S., there are no published notification systems for other locations.
Most general aviation aircraft in the U.S. are required to carry an ELT, depending upon the type or location of operation, while scheduled flights by scheduled air carriers are not. However, in commercial aircraft, a cockpit voice recorder or flight data recorder must contain an underwater locator beacon.
As per 14 CFR 91.207.a.1, ELTs built according to TSO-C91 (of the type described below as "Traditional ELT, unregistered") have not been permitted for new installations since June 21, 1995; the replacing standard was TSO-C91a. Furthermore, TSO-C91/91a ELTs are being replaced / supplemented by the TSO C126 406 MHz  ELT, a far superior unit.
Although monitoring of 121.5 and 243 MHz (Class B) distress signals by satellite ceased in February 2009, the FAA has not mandated an upgrade of older ELT units to 406 in United States aircraft. Transport Canada has put forward a proposed regulatory requirement that requires upgrade to Canadian registered aircraft to either a 406 MHz ELT or an alternate means system; however, elected officials have overruled the recommendation of Transport Canada for the regulation and have asked for a looser regulation to be drafted by Transport Canada. Recent information indicates Transport Canada may permit private, general aviation flight with only an existing 121.5 ELT if there is a placard visible to all passengers stating to the effect that the aircraft does not comply with international recommendations for the carriage of the 406 MHz emergency alerting device and is not detectable by satellites in the event of a crash.
EPIRBs are a component of the Global Maritime Distress and Safety System (GMDSS). Most commercial off-shore working vessels with passengers are required to carry a self-deploying EPIRB, while most in-shore and fresh-water craft are not.
As part of the United States efforts to prepare beacon users for the end of 121.5 MHz frequency processing by satellites, the FCC has prohibited the use of 121.5 MHz EPIRBs as of January 1, 2007 (47 CFR 80.1051). See the United States Coast Guard (USCG) brief on the 121.5/243 Phase-out[dead link].
Personal locator beacons (PLBs)
Personal locator beacons operating on 406 MHz must be registered. PLBs should not be used in cases where normal emergency response exists.
Automatic SOS radios were developed as early as the 1930s.
In the UK, by 1959 the first automatic beacon for liferafts had been produced by Ultra Electronics, and at the same time Burndept produced the TALBE (Talk and Listen Beacon Equipment) - VHF, and SARBE - Search-And-Rescue-Beacon Equipment (UHF) range of beacons which were used by the Fleet Air Arm and later, Royal Air Force. Later, SARBE beacons included a radio for voice communication by the survivor with the rescuing personnel.
The original impetus for the program in the U.S. was the loss of Congressmen Hale Boggs (D-LA) and Nick Begich (D-AK) in the Alaskan wilderness on October 16, 1972. A massive search effort failed to locate them. The result was a U.S. law mandating that all aircraft carry an emergency locator transmitter. Technical and organizational improvements followed.
Cospas-Sarsat is an international organization that has been a model of international cooperation, even during the Cold War. SARSAT means Search And Rescue Satellite Aided Tracking. COSPAS (КОСПАС) is an acronym for the Russian words "Cosmicheskaya Sistema Poiska Avariynyh Sudov" (Космическая Система Поиска Аварийных Судов), which translates to "Space System for the Search of Vessels in Distress". A consortium of Russia, the U.S., Canada and France formed the organization in 1982. Since then, 29 others have joined.
Cospas-Sarsat defines standards for beacons, auxiliary equipment to be mounted on conforming weather and communication satellites, ground stations, and communications methods. The satellites communicate the beacon data to their ground stations, which forward it to main control centers of each nation that can initiate a rescue effort.
The U.S. Coast Guard once promoted an emergency beacon on maritime VHF emergency channels. It now promotes the superior Cospas-Sarsat system, and no longer services emergency beacons on maritime VHF frequencies.
In a Safety Recommendation released September 2007, the U.S. National Transportation Safety Board once again recommended that the U.S. FAA require all aircraft have 406 MHz ELTs. They first recommended this back in 2000 and after vigorous opposition by AOPA, the FAA declined to do so. This recommendation is apparently a reaction to the cessation of 121.5 MHz satellite processing. Citing two recent accidents, one with a 121.5 MHz ELT and one with a 406 MHz ELT, the NTSB concludes that switching all ELTs to 406 MHz is a necessary goal to work towards.
There are also other personal devices in the marketplace which do not meet the standard for 406 MHz devices. These devices are commonly referred to as SEND (Satellite Emergency Notification Device)
GPS aircraft tracking
Active aircraft tracking
There are several active aircraft tracking systems available on the market that use the "bread-crumb approach" to SAR. Rather than relying on an emergency locator transmitter to transmit upon impact, the next generation of emergency locating devices are active tracking devices that send position reports at regular time intervals. If the unit stops transmitting upon impact, the historical transmissions will give the last known location of the aircraft, its speed, direction and altitude. Tracking as an alternative or complement to current technology has recently been encouraged by the Coroner in New Zealand.
SPOT does not use the 406 MHz signal nor the system of satellites. Instead, it depends on the GlobalStar satellite system. It has richer features (for instance, can send many non-emergency signals) - but it does not work in as many places as 406 MHz PLBs - for instance under dense forest canopy or steep canyons. When a user presses the "911" button on a SPOT device an emergency message containing the unit's identification and GPS location is transmitted to the GEOS International Emergency Response Center who then notifies the appropriate emergency agency for the region after first calling the user to ensure the transmission is not accidental.
SPOT additionally has the ability to provide non-emergency web based tracking information. This allows family or friends at home to track the holder's progress. The tracking operates by sending a tracking signal to the GlobalStar network every 10 minutes. This feature can additionally be useful to provide location of an individual even if the individual is unable to activate the emergency '911' button.
Typical costs are $169 plus a $99/year service fee for basic services or $150/yr for basic services and tracking services, as compared to around $250 for a 406-MHz PLB with no service fee.
Spidertracks is also completely independent of the 406 MHz system. A unit in the aircraft periodically transmits its position via the Iridium satellite constellation. The position is recorded. If no position report is received when it is expected, a series of emergency contacts are alerted in sequence. If no response is received, SAR are called with the last recorded position. The aircraft's position is also available via a website.
Yellowbrick, like SPOT, does not use the 406 MHz signal nor the system of satellites. Instead, it depends on the Iridium satellite system. Unlike SPOT, Yellowbrick is a two way system capable of receiving confirmation that the message was received and exchange two-way messages via short emails and SMS. Alert messages are transmitted to destinations specified by the owner.
inReach, like SPOT, does not use the 406 MHz signal nor the system of satellites. Instead, it depends on the Iridium satellite system. Unlike SPOT, inReach is a two way system capable of receiving confirmation that the message was received. Like SPOT, the message is transmitted to the private GEOS International Emergency Response Center who then notifies the appropriate SAR authorities.
inReach also provides tracking capability and two way SMS text messages.
TracMe  is a single use beacon which once activated simply transmits an automated voice message saying "Help - Emergency" once every 15 seconds on a short-range FRS UHF CB frequency until the battery runs out. Tracme does not notify authorities that the user is missing, TracMe's website recommends you arrange for rescue by notifying a friend about your plans, and ask them to call authorities and inform them of your general whereabouts and that you have a TracMe if you are late returning. Then, a search-and-rescue team, if they have purchased a special single purpose tracker sold by TracMe, will need to radio-locate the signal in the area you have told friends you are visiting within the effective radius of the short ranged beacon; 2–4 miles was the maximum range that an experimentally equipped aircraft SAR team was able to achieve in testing. Doug Ritter of Equipped to Survive, an educational NGO which researches and addresses search and rescue public policy and evaluates survival equipment and scenarios, stated with regard to TracMe, "SAR just isn't ready to take advantage of it in any compelling manner and they don't yet appear ready to help out SAR either in an effective manner should someone use one of these tomorrow."  Tracme is sold as a PLB or "Personal Locator Beacon". TracMe has had a dispute with the FCC over the requirement for 406mhz SAR-Sat satellite connection to sell a device as a PLB.
Automatic Packet Reporting System is used by amateur radio operators to track positions and send short messages. Most APRS packets contain a GPS latitude and longitude, so they can be used for both normal and emergency tracking. They also are routed to the Internet, where they are archived for some period of time, and viewable by others. There are several emergency packet types that can indicate distress. Since it is part of the amateur radio service, it costs nothing to transmit on and uses the extensive network, however, one must be a licensed amateur radio operator. There is also no guarantee that an APRS distress packet report would be seen or handled by emergency responders. It would have to be seen by an amateur radio operator and forwarded on.
- 1986 British International Helicopters Chinook crash
- 1996 New Hampshire Learjet crash
- Acronyms and abbreviations in avionics
- Aircraft emergency frequency
- Automatic identification system
- Civil Air Patrol (US Air Force Auxiliary)
- Electric beacon
- ENOS Rescue-System
- Global Maritime Distress and Safety System
- Satellite emergency notification device
- Search and rescue transponder
- Survival radio
- Varig Flight 254
- ITU Radio Regulations, Section IV. Radio Stations and Systems – Article 1.93, definition: emergency position-indicating radiobeacon station
- What happens when I activate my beacon?
- Community Emergency Response Team Participant Handbook
- "SAR statistics". Retrieved 9 Oct 2012.
- "Rescue Stories". Retrieved 9 October 2012.
- Life-saving appliances: including LSA code/ International Maritime Organization (2nd ed.). London. 2010. ISBN 9789280115079.
- See COSPAS-SARSAT document A.001, 2005
- "Archived copy". Archived from the original on 2009-10-12. Retrieved 2009-09-22.
- Position Indicating Radiobeacon (EPIRB) – USCG Navigation Center
- Albert Helfrick, Principles of Avionics, 5th Edition, Avionics Communications, 2009 ISBN 1885544278, p 287
- NASA Search and Rescue Mission Office : Distress Alerting Satellite System (DASS) Archived 2016-03-04 at the Wayback Machine.
- Example of 406 MHz Beacon Coding
- beacon decoder webpage Archived 2012-03-09 at the Wayback Machine., When one enters the transmitted (i.e. GPS-location-included) 15-hex into the decoder, the unmodified 15-hex ID is printed at the bottom of the output of the Beacon Decoder page. This method can be used to confirm that a beacon is encoding the correct 15-hex ID (as printed on the side of the beacon) into its distress messages. Accessed November 23, 2009
- Microsoft Word -G3Oct30.98D.
- RSS-187, Emergency Position Indicating Radio Beacons, Emergency Locator Transmitters, Personal Locator Beacons, and Maritime Survivor Locator Devices
- Sport Aviation: 10. March 2009. Missing or empty
- KANNAD 406 AS
- Milovanovich, C. (7 May 2009). "Inquest into the death of David Iredale" (PDF). Lawlink. Archived from the original (PDF) on 22 March 2011. Retrieved 20 February 2010.
- RSS-187, Emergency Position Indicating Radio Beacons, Emergency Locator Transmitters, Personal Locator Beacons, and Maritime Survivor Locator Devices
- "Inmarsat will withdraw epirb service in 2006 and promises new safety service on next generation I-4 satellites". Archived from the original on December 9, 2006.
- Use of 121.5/243 MHz EPIRBs Banned. BoatUS Magazine. March 2007.
- Emergency Locator Transmitters
- Regulations Amending the Canadian Aviation Regulations (Parts I and VI – ELT) Archived 2015-03-25 at the Wayback Machine. Canada Gazette
- Canada Backs Off 406 ELTs
- COPA Flight 8 Ottawa: July 2009 Update on 4006 MHz ELTs
- "Another Automatic SOS" Flight 15 September 1938 p241
- Safety recommendation (A-07-51). National Transportation Safety Board. 4 September 2007.
- NTSB to FAA: Require 406 MHz ELTs | Doug Ritter’s Equipped.org Blog
- McDonald, Samuel (2015-07-29). "Second Crash Test Harvests Valuable Data to Improve Emergency Response". NASA.
- Kauh, Elaine (2015-08-26). "NASA Completes ELT Crash Tests". AVweb.
- on YouTube
- Ihaka, James (27 May 2010). "Erceg coroner urges use of GPS tracking devices for aircraft". The New Zealand Herald. Retrieved 28 September 2011.
- SPOT Satellite Messenger FIRST LOOK - EQUIPPED TO SURVIVE (tm)
- SPOT Emergency Response
- GEOS Search And Rescue
- How SPOT works
- Live flight tracking | Spidertracks
- Yellowbrick Website Archived 2014-07-22 at the Wayback Machine.
- Official Web site http://www.tracme.com.au/
- TracMe Official Web site FAQ.
- TracMe to FCC: You Can’t Make Us... | Doug Ritter’s Equipped.org Blog
- COSPAS-SARSAT, Document C/S T.001 October 1999
- FCC, Part 80 and GMDSS
- MED, 0735/2001
- RTCM, Standard for 406 MHz Satellite EPIRBs
- Cospas-Sarsat – the International Satellite System For Search and Rescue
- ITU – Maritime mobile Access and Retrieval System (MARS)
- NOAA SARSAT website
- NOAA notice of planned phasing out of 121.5/243 MHz beacons in 2009
- ICAO/IMO Working Paper 10 to 14 September 2007 – Joint Working Group on Harmonization of Aeronautical and Maritime Search and Rescue
- Operation of a Hydrostatic Release Unit
- "EEVblog #368 - EPIRB Teardown (Examination of the components of a 121/5/243Mhz Epirb)". YouTube. 9 October 2012.