# Gauge (firearms)

(Redirected from Gauge (bore diameter))
Gauge
From left to right; a .45 ACP, a .410 bore shotshell, a 20 gauge shotshell, and a 12 gauge shotshell
TypeShotgun
Place of originVarious

The gauge (or commonly bore in British English) of a firearm is a unit of measurement used to express the inner diameter (bore diameter) of the barrel.

Gauge is determined from the weight of a solid sphere of lead that will fit the bore of the firearm and is expressed as the multiplicative inverse of the sphere's weight as a fraction of a pound, e.g., a one-twelfth pound lead ball fits a 12-gauge bore. Thus there are twelve 12-gauge balls per pound, etc.[1] The term is related to the measurement of cannon, which were also measured by the weight of their iron round shot; an 8-pounder would fire an 8 lb (3.6 kg) ball.

Gauge is commonly used today in reference to shotguns, though historically it was also used in large double rifles, which were made in sizes up to 2 bore during their heyday in the 1880s, being originally loaded with black powder cartridges. These very large rifles, sometimes called "elephant guns", were intended for use in Africa and Asia for hunting game.

Gauge is abbreviated "ga.", "ga", or "G".

## Calculating gauge

An n-gauge diameter means that a ball of lead (density 11.34 g/cm3 or 0.4097 lb/in3) with that diameter has a mass equal to 1/n part of the mass of the international avoirdupois pound (approx. 454 grams), that is, that n such lead balls could be cast from a pound weight of lead. Therefore, an n-gauge shotgun or n-bore rifle has a bore diameter (in inches) of approximately

${\displaystyle d_{n}=2{\sqrt[{3}]{{\frac {3}{4\pi }}{\frac {1\mathrm {~lb} /n}{0.4097\mathrm {~lb/in^{3}} }}}}}$

Explanation:

• Divide 1 pound by n to find the mass of each one of the balls
• Divide it by 0.4097 lb/in3 (density of lead) to find the volume of each ball
• Multiply it by 3/4 and divide it by pi, then find its cube root (rearranged from the volume of a sphere equation) to find the radius of each ball
• Multiply it by 2 to change from radius to diameter

This simplifies to the following formula for the internal diameter of the barrel of an n-gauge shotgun:

${\displaystyle d_{n}=1.67/{\sqrt[{3}]{n}}}$ (in inches), or ${\displaystyle d_{n}=42.4/{\sqrt[{3}]{n}}}$ (in millimeters).

Likewise, given the diameter in inches, the gauge is

${\displaystyle n=4.66/d_{n}^{3}}$

The gauge of firearms is determined by. 1 pound / gauge = weight of lead sphere. Caliber of lead sphere is then measured. This is essential information for understanding gauges.

1 Pound / gauge = weight of lead sphere Caliber of lead sphere is then measured
gauge pounds mm inches
0.25 4 67.34 2.651
0.5 2 53.45 2.103
0.75 1+1/3 46.70 1.838
1 1 42.42 1.669
1.5 2/3 37.05 1.459
2 1/2 33.67 1.326
3 1/3 29.41 1.158
4 1/4 26.72 1.052
5 1/5 24.80 0.976
6 1/6 23.35 0.919
6.278 1/6.278 23.00 0.906
7 1/7 22.18 0.873
8 1/8 21.21 0.835
9 1/9 20.39 0.803
10 1/10 19.69 0.775
11 1/11 19.07 0.751
12 1/12 18.53 0.729
13 1/13 18.04 0.710
14 1/14 17.60 0.693
15 1/15 17.21 0.677
16 1/16 16.83 0.663
17 1/17 16.50 0.650
18 1/18 16.19 0.637
20 1/20 15.63 0.615
22 1/22 15.13 0.596
24 1/24 14.70 0.579
26 1/26 14.31 0.564
28 1/28 13.97 0.550
32 1/32 13.36 0.526
36 1/36 12.85 0.506
40 1/40 12.40 0.488
67.62 1/67.62 10.41 0.410

## Gauges in use

Since shotguns were not originally intended to fire solid projectiles, but rather a compressible mass of shot, the actual diameter of the bore can vary. The fact that most shotgun bores are not cylindrical also causes deviations from the ideal bore diameter.

The chamber of the gun is larger, to accommodate the thickness of the shotshell walls, and a "forcing cone" in front of the chamber reduces the diameter down to the bore diameter. The forcing cone can be as short as a fraction of an inch, or as long as a few inches on some guns. At the muzzle end of the barrel, the choke can constrict the bore even further, so measuring the bore diameter of a shotgun is not a simple process, as it must be done away from either end.

Shotgun bores are commonly "overbored" or "backbored", meaning that most of the bore (from the forcing cone to the choke) is slightly larger than the value given by the formula. This is claimed to reduce felt recoil and improve patterning. The recoil reduction is due to the larger bore producing a slower acceleration of the shot, and the patterning improvements are due to the larger muzzle diameter for the same choke constriction, which results in less shot deformation. A 12-gauge shotgun, nominally 18.5 mm (0.73 in), can range from a tight 18 mm (0.71 in) to an extreme overbore of 20 mm (0.79 in). Some also claim an increased velocity with the overbored barrels, up to 15 m/s (49 ft/s), which is due to the larger swept volume of the overbored barrel. Once only found in expensive custom shotguns, overbored barrels are now becoming common in mass-marketed guns. Aftermarket backboring is also commonly done to reduce the weight of the barrel, and move the center of mass backwards for a better balance. Factory overbored barrels generally are made with a larger outside diameter, and will not have this reduction in weight—though the factory barrels will be tougher, since they have a normal barrel wall thickness.

Firing slugs from overbored barrels can result in very inconsistent accuracy, as the slug may be incapable of obturating to fill the oversized bore.

## Sizes in use

left-to-right: .410, 28ga, 20ga, 12ga.

The most common size is 12 gauge,[2] with up to 50% of the overall shotgun market in the United States. The 20 gauge shotgun is favored by shooters uncomfortable with the weight and recoil of a 12 gauge gun, and is popular for upland game hunting. The next most popular sizes are 28 gauge and .410 bore. The 10 gauge and 16 gauge, while a little less common, are still readily available in the United States.

Shotguns and shells exceeding 10 gauge, such as the 8 and 4 gauge, are rather rarely manufactured and only a few makers of the otherwise large market of shotgun, rifle and ammo makers across the United States still produce them. Shells are usually black powder paper cartridges as opposed to the plastic or wax cartridge and smokeless powder of today.

The 11, 15, 18, 2, and 3 gauge shells are rarest of all;[3] owners of these types of rare shotguns will usually have their ammunition custom loaded by a specialist in rare and custom bores. The 14 gauge has not been loaded in the United States since the early 1900s, although the 2+9/16 inch hull is still made in France.[3] The very small 24 and 32 gauges are still produced and used in some European and South American countries. Punt guns are rarely encountered.

Garden Gun calibers: 9mm Flobert shot, 9mm Flobert shot, .22 Long Rifle shot, .22 Long Rifle, .22 Long Rifle shot, .22 CB Short, and 9mm Flobert BB cap

Also seen in limited numbers are smoothbore firearms in calibers smaller than .360 such as .22 Long Rifle (UK No.1 bore) and 9mm Flobert rimfire (UK No.3 bore), designed for short range pest control and garden guns. The No.2 bore (7 mm) has long been obsolete. All three of these rimfires are available in shot and BB-cap.[4][5]

### Gauge and shot type

A 10-gauge (3+1/2″) shotgun shell shown next to a United States quarter

The 10 gauge narrowly escaped obsolescence when steel and other nontoxic shot became required for waterfowl hunting, since the larger shell could hold the much larger sizes of low-density steel shot needed to reach the ranges necessary for waterfowl hunting. The move to steel shot reduced the use of 16 and 20 gauges for waterfowl hunting, and smaller 2¾″ (70mm) 12 gauge shells as well. However, the advent of the 3.5 in (89 mm) 12 gauge shell, with its higher SAAMI pressure rating compared to standard 12 gauge guns, begin to approach the performance of the 10 gauge loads. Newer nontoxic shots, such as bismuth and tungsten-nickel-iron alloys, and even tungsten-polymer blends, regain much or all of the performance loss, but are much more expensive than steel or lead shot.[6] However, laboratory research indicates that tungsten alloys can actually be quite toxic internally.[7]

### Sizes found in the UK

4 bore 4" (100mm)
8 bore 3¼" (83mm)
10 bore 2⅝" (67mm), 2⅞" (73mm), 3½" (89mm)
12 bore 1¾" (45mm), 2" (51mm), 2¼" (57mm), 2½" (63mm), 2¾" (70mm), 3" (76mm), 3½" (89mm)
14 bore 2½" (63mm)
16 bore 2½" (63mm), 2¾" (70mm)
20 bore 2½" (63mm), 2¾" (70mm), 3" (76mm)
24 bore 2½" (63mm)
28 bore 2½" (63mm), 2¾" (70mm)
32 bore 2½" (63mm)
.410 bore 2" (51mm), 2½" (63mm), 3" (76mm)
.360 bore 1¾" (9 x 45mm)
9mm (No.3 bore) rimfire [0.5"], 9mm (No.3 bore) long rimfire [1.4"]
7mm (No.2 bore) rimfire
6mm (No.1 bore) short rimfire, 6mm (No.1 bore) long rimfire

## Conversion guide

Portrait of Frederick Courteney Selous with his 4 bore single-shot Boer rifle and African hunting regalia, 1876

The below table lists various gauge sizes with weights. The bores marked * are found in punt guns and rare weapons only. However, 4 gauge were sometimes found used in blunderbuss guns made for coach defense and protection against piracy. The .410 bore and 23mm caliber are exceptions; they are actual bore sizes, not gauges. If the .410 and 23 mm were measured traditionally, they would be 67.62 gauge and 6.278 gauge, respectively.

Gauge
(bore)
Diameter Weight of unalloyed (pure) lead ball
(mm) (in) grams ounces grains
AA* 101.60 4.000 6225.52 219.6 96,080
* 76.20 3.000 2626.39 92.64 40,530
0.25* 67.34 2.651 1814.36 64.000 28,000
0.5* 53.45 2.103 907.18 32.000 14,000
A* 50.80 2.000 778.19 27.45 12,010
0.75* 46.70 1.838 604.80 21.336 9328
1* 42.42 1.669 453.59 16.000 7000
* 38.10 1.500 328.3 11.58 5066
1.5* 37.05 1.459 302.39 10.667 4667
2* 33.67 1.326 226.80 8.000 3500
3* 29.41 1.158 151.20 5.333 2333
4 26.72 1.052 113.40 4.000 1750
B* 25.40 1.000 97.27 3.43 1501
5* 24.80 0.976 90.72 3.200 1400
6* 23.35 0.919 75.60 2.667 1166
6.278 23.00 0.906 72.26 2.549 1114
7* 22.18 0.873 64.80 2.286 1000
8 21.21 0.835 56.70 2.000 875
9* 20.39 0.803 50.40 1.778 778
10 19.69 0.775 45.36 1.600 700
11* 19.07 0.751 41.24 1.454 636
12 18.53 0.729 37.80 1.333 583
13* 18.04 0.710 34.89 1.231 538
14 17.60 0.693 32.40 1.143 500
15* 17.21 0.677 30.24 1.067 467
16 16.83 0.663 28.35 1.000 438
17* 16.50 0.650 26.68 0.941 412
18* 16.19 0.637 25.20 0.889 389
20 15.63 0.615 22.68 0.800 350
22* 15.13 0.596 20.62 0.728 319
24 14.70 0.579 18.90 0.667 292
26* 14.31 0.564 17.44 0.615 269
28 13.97 0.550 16.20 0.571 250
32 13.36 0.526 14.17 0.500 219
36 12.85 0.506 12.59 0.444 194
40 12.40 0.488 11.34 0.400 175
67.62 10.41 0.410 6.71 0.237 104

Note: Use of this table for estimating bullet masses for historical large-bore rifles is limited, as this table assumes the use of round ball, rather than conical bullets; for example, a typical 4 bore rifle from circa 1880 used a 2,000-grain (4.57 oz) bullet, or sometimes slightly heavier, rather than using a 4-ounce round lead ball. (Round balls give progressively much worse external ballistic performance than conical bullets at ranges greater than about 75 yards.) In contrast, a 4-bore express rifle often used a 1,500-grain (3.43 oz) bullet wrapped in paper to keep lead buildup to a minimum in the barrel. In either case, assuming a 4-ounce mass for a 4-bore rifle bullet from this table would be inaccurate, although indicative.