|Unit system||imperial/US units|
|1 gunter's chain in ...||... is equal to ...|
|imperial/US units||22 yd|
|metric (SI) units||20.1 m|
|Unit system||imperial/US units|
|1 gunter's link in ...||... is equal to ...|
|imperial/US units|| 1/ Gunter's chain|
|metric (SI) units||200 mm|
Gunter's chain (also known as Gunter’s measurement) is a distance measuring device used for surveying. It was designed and introduced in 1620 by English clergyman and mathematician Edmund Gunter (1581–1626). It enabled plots of land to be accurately surveyed and plotted, for legal and commercial purposes.
The 66-foot (20.1 m) chain is divided into 100 links, usually marked off into groups of 10 by brass rings or tags which simplify intermediate measurement. Each link is thus 7.92 inches (201 mm) long. A quarter chain, or 25 links, measures 16 feet 6 inches (5.03 m) and thus measures a rod (or pole). Ten chains measure a furlong and 80 chains measure a statute mile.
Gunter's chain reconciled two seemingly incompatible systems: the traditional English land measurements, based on the number four, and decimals based on the number 10. Since an acre measured 10 square chains in Gunter's system, the entire process of land area measurement could be computed using measurements in chains, and then converted to acres by dividing the results by 10. Hence 10 chains by 10 chains equals 10 acres, 5 chains by 5 chains equals 2.5 acres.
The method of surveying a field or other parcel of land with Gunter's chain is to first determine corners and other significant locations, and then to measure the distance between them, taking two points at a time. The surveyor is assisted by a chainman. A ranging rod (usually a prominently coloured wooden pole) is placed in the ground at the destination point. Starting at the originating point the chain is laid out towards the ranging rod, and the surveyor then directs the chainman to make the chain perfectly straight and pointing directly at the ranging rod. A pin is put in the ground at the forward end of the chain, and the chain is moved forward so that its hind end is at that point, and the chain is extended again towards the destination point. This process is called ranging, or in the US, chaining; it is repeated until the destination rod is reached, when the surveyor notes how many full lengths (chains) have been laid, and he can then directly read how many links (one-hundredth parts of the chain) are in the distance being measured. The chain usually ends in a handle which may or may not be part of the measurement. An inner loop (visible in the NMAH photograph) is the correct place to put the pin for some chains. Many chains were made with the handles as part of the end link and thus were included in the measurement.
The whole process is repeated for all the other pairs of points required, and it is a simple matter to make a scale diagram of the plot of land. The process is surprisingly accurate and requires only very low technology. Surveying with a chain is simple if the land is level and continuous—it is not physically practicable to range across large depressions or significant waterways, for example. On sloping land, the chain was to be "leveled" by raising one end as needed, so that undulations did not increase the apparent length of the side or the area of the tract.
Unit of length
Although link chains were later superseded by the steel ribbon tape (a form of tape measure), its legacy was a new statutory unit of length called the chain, equal to 66 feet (or 100 links). This unit still exists as a location identifier on British railways, as well as in some areas of America. In the United States (US), for example, Public Lands Survey plats are published in the chain unit to maintain the consistency of a two-hundred-year-old database. In the Midwest of the US it is not uncommon to encounter deeds with references to chains, poles, or rod units, especially in farming country. Minor roads surveyed in Australia and New Zealand in the 19th and early 20th centuries are customarily one chain wide.
Similar measuring chains
A similar American system, of lesser popularity, is Ramsden’s or the engineer’s system, where the chain consists also of 100 links, each one foot (0.3048 m) long. The original of such chains was that constructed, to very high precision, for the measurement of the baselines of the Anglo-French Survey (1784–1790) and the Principal Triangulation of Great Britain.
The even less common Rathborn system, also from the 17th century, is based on a 200-link chain of two rods (33 feet, 10.0584 m) length. Each rod (or perch or pole) consists of 100 links, (1.98 inches, 50.292 mm each), which are called seconds (″), ten of which make a prime (′, 19.8 inches, 0.503 m).
In France after the French Revolution, and later in countries that had adopted the Metric System, 10 metres (32 ft 9.7 in) chains, of 50 links each 200 millimetres (7.87 in) long were used until the 1950s.
- Slater; Saunders. "Rods, poles and perches". www.northcravenheritage.org.uk. Retrieved 22 July 2018.
- John Love (1688). "VII : How to cast up the Contents of a Plot of Land". Geodaesia: or, The art of surveying and measuring land made easy : shewing, by plain and practical rules, how to survey, protract, cast up, reduce or divide any piece of land whatsoever : with new tables for the ease of the surveyor in reducing the measure of land. London: J. Taylor. p. 122.
- Manthey, David (2002). "How to Make a Gunter's Chain". Orbital Central. Retrieved 2 August 2018.
- "Types of Chains". The Constructor. Retrieved 4 August 2018.
- Punmia, B. C. [https://books.google.com/books?id=EM-sLyVmMwIC&pg=PA39&lpg=PA39&dq=surveyor+chain+handle&source=bl&ots=JJBCFlWMqA&sig=ioTKumg5ztgcXBiCcCGUYi2QZUs&hl=en&sa=X&ved=2ahUKEwj_ysfx1NPcAhVLMqwKHdsODYk4ChDoATAIegQIAhAB#v=onepage&q=surveyor%20chain%20handle&f=false p. 39. Retrieved August 4, 2018.
- Holloway, Thomas (1881). The practical surveyor. Horace Cox. London. pp. 22–24. Retrieved April 7, 2009.
- Nesbit, Anthony (1847). A complete treatise on practical land-surveying, Ninth edition. Longman, Brown, Green and Longmans. London. p. 29. Retrieved April 7, 2009.
- McKay, Donald F. (ed.) (2009). "Land Title Surveys in New Zealand" Archived 2015-05-23 at the Wayback Machine. Chapter 2, Section 8: Public Roads. New Zealand Institute of Surveyors.
- Craven, Ian; Gray, Martin; Stoneham, Geraldine (1994). Australian Popular Culture. Cambridge University Press. p. 27. ISBN 0-521-46667-9.
- MCC (2018). "Law 6 – the pitch". Retrieved 23 November 2018.
- Zupko, Ronald Edward. A Dictionary of Weights and Measures for the British Isles
- Denny, Milton. "The Colonial Surveyor in Pennsylvania", Surveyors Historical Society, 2013.
- Instruments used in Surveying My Agriculture information bank
- Surveying I - R. Gopalakrishnan, Sri Venkateswara College of Engineering (pdf)
- Plomion, Charles. Arithmétique-Cours élémentaire, Librairie A. Hatier, Paris, 1925