This article needs additional citations for verification. (August 2008) (Learn how and when to remove this template message)
A current–voltage characteristic or I–V curve (current–voltage curve) is a relationship, typically represented as a chart or graph, between the electric current through a circuit, device, or material, and the corresponding voltage, or potential difference across it.
In electronics, the relationship between the direct current (DC) through an electronic device and the DC voltage across its terminals is called a current–voltage characteristic of the device. Electronic engineers use these charts to determine basic parameters of a device and to model its behavior in an electrical circuit. These characteristics are also known as IV curves, referring to the standard symbols for current and voltage.
In electronic components with more than two terminals, such as vacuum tubes and transistors, the current-voltage relationship at one pair of terminals may depend on the current or voltage on a third terminal. This is usually displayed on a more complex current–voltage graph with multiple curves, each one representing the current-voltage relationship at a different value of current or voltage on the third terminal.
For example the diagram at right shows a family of IV curves for a MOSFET as a function of drain voltage with overvoltage (VGS − Vth) as a parameter.
The simplest IV curve is that of a resistor, which according to Ohm's Law exhibits a linear relationship between the applied voltage and the resulting electric current; the current is proportional to the voltage, so the IV curve is a straight line through the origin with positive slope. The reciprocal of the slope is equal to the resistance.
The IV curve of an electrical component can be measured with an instrument called a curve tracer. The transconductance and Early voltage of a transistor are examples of parameters traditionally measured from the device's IV curve.
Types of IV curves
The shape of an electrical component's characteristic curve reveals much about its operating properties. IV curves of different devices can be grouped into categories:
- Active vs passive: Devices which have IV curves which are limited to the first and third quadrants of the IV plane, passing through the origin, are passive components (loads), that consume electric power from the circuit. Examples are resistors and electric motors. Conventional current always flows through these devices in the direction of the electric field, from the positive voltage terminal to the negative, so the charges lose potential energy in the device, which is converted to heat or some other form of energy.
- In contrast, devices with IV curves which pass through the second or fourth quadrants are active components, power sources, which can produce electric power. Examples are batteries and generators. When it is operating in the second or fourth quadrant, current is forced to flow through the device from the negative to the positive voltage terminal, against the opposing force of the electric field, so the electric charges are gaining potential energy. Thus the device is converting some other form of energy into electric energy.
- Linear vs nonlinear: A straight line through the origin represents a linear circuit element, while a curved line represents a nonlinear element. For example, resistors, capacitors, and inductors are linear, while diodes and transistors are nonlinear. An IV curve which is a straight line through the origin with positive slope represents a linear or ohmic resistor, the most common type of resistance encountered in circuits. It obeys Ohm's law; the current is proportional to the applied voltage over a wide range. Its resistance, equal to the reciprocal of the slope of the line, is constant. A curved IV line represents a nonlinear resistance, such as a diode. In this type the resistance varies with the applied voltage or current.
- Negative resistance vs positive resistance: An IV curve which is nonmonotonic (having peaks and valleys) represents a device which has negative resistance. Regions of the curve which have a negative slope (declining to the right) represent operating regions where the device has negative differential resistance, while regions of positive slope represent positive differential resistance. Tunnel diodes and Gunn diodes are examples of components that have negative resistance.
- Hysteresis vs single-valued: Devices which have hysteresis; that is, in which the current-voltage relation depends not only on the present applied input but also on the past history of inputs, have IV curves consisting of families of closed loops. Each branch of the loop is marked with a direction represented by an arrow. Examples of devices with hysteresis include iron-core inductors and transformers, thyristors such as SCRs and DIACs, and gas-discharge tubes such as neon lights.
IV curve similar to a tunnel diode characteristic curve. It has negative resistance in the shaded voltage region, between v1 and v2
DIAC IV curve. VBO is the breakover voltage.
Gunn diode IV curve, showing negative differential resistance with hysteresis (notice arrows)
While V–I curves are applicable to any electrical system, they find wide use in the field of biological electricity, particularly in the sub-field of electrophysiology. In this case, the voltage refers to the voltage across a biological membrane, a membrane potential, and the current is the flow of charged ions through channels in this membrane. The current is determined by the conductances of these channels.
In the case of ionic current across biological membranes, currents are measured from inside to outside. That is, positive currents, known as "outward current", corresponding to positively charged ions crossing a cell membrane from the inside to the outside, or a negatively charged ion crossing from the outside to the inside. Similarly, currents with a negative value are referred to as "inward current", corresponding to positively charged ions crossing a cell membrane from the outside to the inside, or a negatively charged ion crossing from inside to outside.
The figure to the right shows an V–I curve that is more relevant to the currents in excitable biological membranes (such as a neuronal axon). The blue line shows the V–I relationship for the potassium ion. Note that it is linear, indicating no voltage-dependent gating of the potassium ion channel. The yellow line shows the V–I relationship for the sodium ion. Note that it is not linear, indicating that the sodium ion channel is voltage-dependent. The green line indicates the I–V relationship derived from summing the sodium and potassium currents. This approximates the actual membrane potential and current relationship of a cell containing both types of channel.
|Wikimedia Commons has media related to Device current-voltage characteristics.|
- H. J. van der Bijl (1919). "Theory and Operating Characteristics of the Themionic Amplifier". Proceedings of the IRE. Institute of Radio Engineers. 7 (2): 97–126. doi:10.1109/JRPROC.1919.217425.