Diving helmet

From Wikipedia, the free encyclopedia
  (Redirected from Lightweight demand helmet)
Jump to navigation Jump to search
Diving helmet
Copper and brass three bolt Soviet diving helmet.
Other names
  • Copper hat
  • Standard diving helmet
  • Free flow helmet
  • Lightweight demand helmet
  • Reclaim helmet
UsesProvision of breathing gas, communications, underwater vision and head protection to underwater divers
US Navy Diver using Kirby Morgan 37 diving helmet[1]

A diving helmet is a rigid head enclosure with a breathing gas supply used in underwater diving. They are worn mainly by professional divers engaged in surface-supplied diving, though some models can be used with scuba equipment. The upper part of the helmet, known colloquially as the hat or bonnet, may be secured to the diver or diving suit by a lower part, known as a neck dam, breastplate, or corselet, depending on the construction and regional language preferences.

The helmet seals the whole of the diver's head from the water, allows the diver to see clearly underwater, provides the diver with breathing gas, protects the diver's head when doing heavy or dangerous work, and usually provides voice communications with the surface (and possibly other divers). If a helmeted diver becomes unconscious but is still breathing, the helmet will remain in place and continue to deliver breathing gas until the diver can be rescued. In contrast, the scuba regulator typically used by recreational divers must be held in the mouth by bite grips, and it can fall out of an unconscious diver's mouth and result in drowning.[2]

Before the invention of the demand regulator, all diving helmets used a free-flow design. Gas was delivered at an approximately constant rate, independent of the diver's breathing, and flowed out through an exhaust valve against a slight over-pressure. Most modern helmets incorporate a demand valve so the helmet only delivers breathing gas when the diver inhales. Free-flow helmets use much larger quantities of gas than demand helmets, which can cause logistical difficulties and is very expensive when special breathing gases (such as heliox) are used. They also produce a constant noise inside the helmet, which can cause communication difficulties. Free-flow helmets are still preferred for some applications of hazardous materials diving, because their positive-pressure nature can prevent the ingress of hazardous material in case the integrity of the suit or helmet is compromised. They also remain relatively common in shallow-water air diving, where gas consumption is of little concern, and in nuclear diving because they must be disposed of after some period of use due to irradiation; free-flow helmets are significantly less expensive[citation needed] to purchase and maintain than demand types.

Most modern helmet designs are sealed to the diver's skin at the neck using a neoprene or latex "neck dam" which is independent of the suit, allowing the diver a choice of suits depending on the dive conditions. When divers must work in contaminated environments such as sewage or dangerous chemicals, the helmet (usually of the free-flow type or using a series exhaust valve system) is directly sealed to a special dry suit (commonly made of a fabric with a smooth vulcanised rubber outer surface) to completely isolate and protect the diver. This equipment is the modern equivalent of the historic "Standard diving dress".


Basic components and their function:

  • Helmet casing – A rigid watertight structure that encloses the diver's head and supports most of the other components.
  • Lower seal – A means of excluding water from the helmet
    • Direct to dry suit – The helmet may be sealed directly to the neck opening of the dry suit, making the helmet and suit a single watertight unit. The weight of the helmet is carried by the head and neck, so it must be nearly neutrally buoyant
    • Neck dam – The helmet may clamp to a neck dam, supported by a rigid ring. The neck dam seals against the skin of the divers neck in the same way that the neck seal of a dry suit works, making the helmet a sealed unit independent of the suit, which may be a dry suit, wet suit or hot-water suit, or even just a pair of overalls in warm water The weight of the helmet is carried by the head and neck, so it must be nearly neutrally buoyant.
    • Breastplate/corselet – An alternative system is for the helmet to seal to a corselet or breastplate, which in turn is sealed to the ddry suit. The helmet and suit become a single sealed unit, somewhat more complex than with a direct seal, but easier to put on and take off. The weight of the helmet is carried on the shoulders via the breastplate, so it does not have to be neutrally buoyant, and can be weighted or held down by a jocking strap.
  • Faceplate – The diver's window on the world. A transparent window in the front of the helmet. If the helmet is light and carried directly on the head and neck, and can move with the head, it is usually relatively small, and the helmet too is compact and relatively light. If the helmet is supported by the shoulders it cannot turn with the head, and must have a larger volume with a larger viewport or more than one viewport to give an adequate field of vision.
  • Gas supply – The breathing gas supply is connected to the helmet. This is usually a surface supply hose attached through a non-return valve to a gas block with a bailout gas supply connected to the bailout valve on the gas block.
    • Inlet valve or demand valve – The primary gas supply may be free-flow or demand controlled. If it is demand controlled there is usually a free-flow bypass, which may also serve as a defogging system, by blowing air over the inner face of the viewport.
    • An internal oro-nasal mask is used in demand supplied helmets to minimise dead space.
  • Gas exhaust system – Exhaled gas is exhausted from the helmet through non-return valves, either directly to the surrounding water, or via a reclaim regulator system through a hose to the surface.
  • Voice communications microphone and headphone speakers connected to the surface via copper conductors in the umbilical cable.
  • Nose blocker – A device is provided which the diver can use to block the nose for ear equalising maneuvers.
  • Other accessories may be present, such as a lifting handle, ballast weights, light and video camera brackets, a welding visor, spitcock and internal padding.


Deane brothers[edit]

1842 sketch of the Deane brothers' diving helmet, the first surface-supplied diving dress equipment in the world.

The first successful diving helmets were produced by the brothers Charles and John Deane in the 1820s.[3] Inspired by a fire accident he witnessed in a stable in England,[4] he designed and patented a "Smoke Helmet" to be used by firemen in smoke-filled areas in 1823. The apparatus comprised a copper helmet with an attached flexible collar and garment. A long leather hose attached to the rear of the helmet was to be used to supply air - the original concept being that it would be pumped using a double bellows. A short pipe allowed breathed air to escape. The garment was made of leather or airtight cloth, secured by straps.

The brothers lacked money to build the equipment themselves, so they sold the patent to their employer, Edward Barnard. In 1827, the first smoke helmets were built, by German-born British engineer Augustus Siebe. In 1828 the brothers decided to find another application for their device and converted it into a diving helmet. They marketed the helmet with a loosely attached "diving suit" so that a diver could perform salvage work, but only in a fully vertical position (otherwise water entered the suit).[3]

In 1829 the Deane brothers sailed from Whitstable for trials of their new underwater apparatus, establishing the diving industry in the town. In 1834 Charles used his diving helmet and suit in a successful attempt on the wreck of Royal George at Spithead, during which he recovered 28 of the ship's cannon. In 1836, John Deane recovered from the discovered Mary Rose shipwreck timbers, guns, longbows, and other items.

By 1836 the Deane brothers had produced the world's first diving manual, Method of Using Deane's Patent Diving Apparatus, which explained in detail the workings of the apparatus and pump, and safety precautions.

The Siebe helmet[edit]

Siebe's improved design in 1873.

In the 1830s the Deane brothers asked Siebe to apply his skill to improve their underwater helmet design.[5] Expanding on improvements already made by another engineer, George Edwards, Siebe produced his own design; a helmet fitted to a full length watertight canvas diving suit. The equipment included an exhaust valve in the helmet, which allowed excess air to escape without allowing water to flow in. The closed diving suit, connected to an air pump on the surface, became the first effective standard diving dress, and the prototype of hard-hat rigs still in use today.

Siebe introduced various modifications on his diving dress design to accommodate the requirements of the salvage team on the wreck of HMS Royal George, including making the helmet be detachable from the corselet; his improved design gave rise to the typical standard diving dress which revolutionised underwater civil engineering, underwater salvage, commercial diving and naval diving.[5]

Lightweight helmets[edit]

Commercial diver and inventor Joe Savoie is credited with inventing the neck dam in the 1960s, which made possible a new era of lightweight helmets, including the Kirby Morgan Superlite series (an adaption of Morgan's existing "Band Mask" into a full helmet.) Savoie chose not to patent his invention because of his desire to improve diver safety.[citation needed] The neck dam seals the helmet around the diver's neck in the same way that a dry suit neck seal works, using similar materials. This allows the helmet to be carried on the head and not on a corselet, so the helmet can turn with the head and can therefore be a much closer fit, which considerably reduces the volume, and as the helmet must be ballasted for neutral buoyancy, the overall weight is reduced.


Standard diving helmet (Copper hat)[edit]

Historically, deep sea diving helmets ranged from the no bolt to two bolt to four bolt helmets; helmets with six, eight, or 12 bolts; and Two-Three, Twelve-Four, and Twelve-Six bolt helmets. Bolts being the method of securing the helmet to the diving suit. The helmet could also be secured to the breastplate (corselet) by bolts as in the case of US twelve-four helmets (12 bolts to the suit, four bolts seal helmet to corselet). The no-bolt helmet used a spring-loaded clamp to secure the helmet to corselet over the suit. Swedish helmets were distinctive for using a neck ring instead of a corselet, a pioneer of modern diving equipment but hugely cumbersome and uncomfortable for the diver. This equipment is commonly referred to as Standard diving dress and "heavy gear."[citation needed]

The US Navy Mk V helmet is still in production to order. In 2016 DESCO Corporation purchased the assets of Morse Diving International and began producing Morse helmets under the A. J. Morse and Son brand. The US Navy Mark V Helmet is available in either make with the minor manufacturing differences intact. While the Mark V is a US Navy design and all helmets should have been identical, models from Morse, Schrader, DESCO, and Miller Dunn all had differences. Brails from a Miller Dunn are difficult to fit on another maker's helmet. Early Miller Dunn Mark V helmets had gussets on the interior radius of the air and communication elbows. Schrader Mark V helmets used yellow brass castings instead of red brass like other makers. Schrader also canted their spitcock body. The standard Mk V weighs approximately 55 lb (25 kg) complete.[6]

A small number of copper Heliox helmets were made for the US Navy by the Second World War. These helmets were Mk Vs modified by the addition of a bulky brass carbon dioxide scrubber chamber at the rear, and are easily distinguished from the standard model. The Mk V Helium weighs about 93 lb (42 kg) complete (bonnet, scrubber canister and corselet)[7] These helmets and similar models manufactured by Kirby Morgan, Yokohama Diving Apparatus Company and DESCO used the scrubber as a gas extender, a form of semi-closed rebreather system, where helmet gas was circulated through the scrubber by entraining the helmet gas in the flow from an injector supplying fresh gas, a system pioneered by Dräger in 1912.[8]

Four companies produced Mark V diving helmets for the US Navy: Morse Diving Equipment Company of Boston, Massachusetts, A Schrader's Son of Brooklyn, New York, Miller-Dunn Diving Co. of Miami, Florida and Diving Equipment and Salvage Co. (later Diving Equipment Supply Co.) of Milwaukee, Wisconsin.[citation needed]

Shallow water helmet[edit]

The shallow water helmet is a very simple concept: a helmet with viewports which is fitted by lowering over the diver's head to rest on the shoulders. It must be slightly negative when filled with air so that it does not float off the diver in use. Air is supplied through a low pressure hose and escapes at the bottom of the helmet, which is not sealed to the suit, and can be lifted off by the diver in an emergency. The helmet will flood if the diver leans over or falls over. The shallow water helmet generally has a handle on top to help the tender lift it onto and off the diver when out of the water. The structure is variable, and ranges from relatively heavy castings to lighter sheet metal shells with additional ballast.[9]

The concept has been used for recreational diving as a breathing system for use by untrained tourists in the direct care of a dive leader in a benign diving environment, marketed as the Sea Trek diving system.[10][11]

Lightweight demand helmets[edit]

Surface supplied lightweight open circuit demand helmet

Open circuit helmets[edit]

Notable modern commercial helmets include the Kirby Morgan Superlite-17 from 1975 and developments from that model. These helmets are of the demand type, built on a fiberglass shell with chrome-plated brass fittings, and are considered the standard in modern commercial diving for most operations.[12]

Kirby Morgan dominates the new helmet market, but there have been other notable manufacturers including Savoie, Miller, Gorski and Swindell. Many of these are still in use; a new helmet represents an investment of several thousand dollars, and most divers purchase their own or rent one from their employer.[citation needed]

Oceaneering bought out the Ratcliffe helmet, often known by its nickname "Rat Hat". It can function in either free-flow or demand mode.[citation needed]

Reclaim helmets[edit]

Reclaim helmets use a surface supply system to provide breathing gas to the diver in the same way as in the open circuit helmets, but also have a return system to reclaim and recycle the exhaled gas to save the expensive helium diluent, which would be discharged to the surrounding water and lost in an open circuit system. The reclaimed gas is discharged from the helmet through a back-pressure regulator and returned to the surface through a hose in the umbilical which is provided for this purpose, passed through a scrubber to remove carbon dioxide, blended with oxygen to the required mix and repressurised for immediate re-use or stored for later use.[13][14]

In order to allow the exhaust gas to be discharged from the helmet safely, it must pass through an exhaust back-pressure regulator, which works on the same principle to a built-in breathing system exhaust valve, activated by the pressure difference between the interior of the helmet and the ambient pressure. The reclaim exhaust valve may be a two-stage valve for lower resistance, and will generally have a manual bypass valve which allows exhaust to the ambient water. The helmet will have an emergency flood valve to prevent possible exhaust regulator failure from causing a helmet squeeze before the diver can bypass it manually.[15]

Free-flow helmets[edit]

The DESCO "air hat" is a metal free-flow helmet, designed in 1968 and still in production. Although it has been updated several times, the basic design has remained constant and all upgrades can be retrofitted to older helmets. Its robust and simple design (it can be completely disassembled in the field with only a screwdriver and wrench) makes it popular for shallow-water operations and hazardous materials diving. The helmet is secured to the diver by means of a "jock strap" which runs between the legs, and buoyancy can be fine-tuned by adjusting intake and exhaust valves. Concept and operation are very similar to the standard diving helmet.[16]

Light-weight transparent dome type helmets have also been used. For example, the Sea Trek surface supplied system, developed in 1998 by Sub Sea Systems, is used for recreational diving.[17][11] Also the Lama, developed by Yves Le Masson in the 1970s, has been used in television to let viewers see the face and hear the voice of the presenter speaking underwater.[18]


  • flooding
  • squeeze
  • protection of the airway
  • environmental protection: impact, noise, thermal


An alternative to the diving helmet that allows communication with the surface is the full face diving mask. These cover the diver's face and are held onto their head by adjustable straps.[19]

"Diving helmet" may also refer to a rigid safety helmet like a workman's helmet that covers the top and back of the head, but is not sealed. These may be worn with a full-face mask to provide impact protection.[citation needed]

During the First World War the British Army used a few diving helmets out of water as emergency protection from mustard gas.[citation needed]

See also[edit]


  1. ^ Curley, MD (1986). "Human Factors Evaluation of the Superlite 37B Helmet in the Surface- Supplied, Open-Circuit Mode". US Navy Experimental Diving Unit Technical Report. NEDU-11-85. Retrieved 2008-09-09.
  2. ^ Mitchell, Simon J; Bennett, Michael H; Bird, Nick; Doolette, David J; Hobbs, Gene W; Kay, Edward; Moon, Richard E; Neuman, Tom S; Vann, Richard D; Walker, Richard; Wyatt, HA (2012). "Recommendations for rescue of a submerged unresponsive compressed-gas diver". Undersea & Hyperbaric Medicine. 39 (6): 1099–108. PMID 23342767. Retrieved 2013-03-03.
  3. ^ a b The Infernal Diver by John Bevan, Hardcover - 314 pages (27 May 1996), Submex Ltd; ISBN 0-9508242-1-6
  4. ^ Heiser, Ed (25 June 2016). "The Origin Of Scuba Diving". www.heiserclan.com. Retrieved 26 November 2019.
  5. ^ a b Acott, C. (1999). "JS Haldane, JBS Haldane, L Hill, and A Siebe: A brief resume of their lives". South Pacific Underwater Medicine Society Journal. 29 (3). ISSN 0813-1988. OCLC 16986801. Retrieved 2008-07-13.
  6. ^ Cardoza, Rod. "The U.S. Navy Mark V - Diving deep into authentication". Retrieved 2013-12-18.
  7. ^ Staff. "DESCO 29019 Mark V Diving Helmet - Navy Helium Helmet with Single Exhaust Valve (early version)". Retrieved 2018-02-15.
  8. ^ "Going deep". www.divingheritage.com. Retrieved 2 July 2019.
  9. ^ "Shallow water Diving Helmets Main Page". www.divingheritage.com. Retrieved 22 November 2019.
  10. ^ Staff. "Untitled equipment page". www.sea-trek.com. Retrieved 26 November 2019.
  11. ^ a b Staff. "Untitled FAQ list". www.sea-trek.com. Retrieved 26 November 2019.
  12. ^ "Kirby Morgan DSI dive helmets" (PDF). kirbymorgan.com. Retrieved 2016-09-07.
  13. ^ "Reclaim Basic Set Up" (PDF). www.subseasa.com. Retrieved 10 March 2020.
  14. ^ Bevan, John, ed. (2005). "Section 5.3". The Professional Divers's Handbook (second ed.). Gosport, Hampshire: Submex Ltd. p. 238. ISBN 978-0950824260.
  15. ^ Operation and Maintenance Manual for the 17C Ultrajewel 601 Helmet Part Number: A10170 Document Number: P1884-OM-56 (Revision: 8 ed.). JFD Divex.
  16. ^ Larn, Richard; Whistler, Rex (1993). Commercial Diving Manual (3rd ed.). Newton Abbott, UK: David and Charles. ISBN 0-7153-0100-4.
  17. ^ Staff. "Equipment options". Sea Trek dive helmet. Archived from the original on April 1, 2009. Retrieved February 21, 2009.
  18. ^ "Lama dive helmet". divingheritage.com. Retrieved 2016-09-07.
  19. ^ Norfleet WT, Hickey DD, Lundgren CE (November 1987). "A comparison of respiratory function in divers breathing with a mouthpiece or a full face mask". Undersea Biomedical Research. 14 (6): 503–26. PMID 3120386. Retrieved 2008-08-31.

External links[edit]