MOSFET

From Wikipedia, the free encyclopedia
  (Redirected from MOS transistor)
Jump to navigation Jump to search
MOSFET, showing gate (G), body (B), source (S) and drain (D) terminals. The gate is separated from the body by an insulating layer (pink).

The metal–oxide–semiconductor field-effect transistor (MOSFET, MOS-FET, or MOS FET), also known as the metal–oxide–silicon transistor (MOS transistor, or MOS),[1] is a type of field-effect transistor that has an insulated gate and is fabricated by the controlled oxidation of a semiconductor, typically silicon. The voltage of the covered gate determines the electrical conductivity of the device; this ability to change conductivity with the amount of applied voltage can be used for amplifying or switching electronic signals. The MOSFET was invented by Egyptian engineer Mohamed M. Atalla and Korean engineer Dawon Kahng at Bell Labs in November 1959. It is the basic building block of modern electronics, and the most frequently manufactured device in history, with an estimated total of 13 sextillion (1.3 × 1022) MOSFETs manufactured between 1960 and 2018.

The MOSFET is the most common semiconductor device in digital and analog circuits, and the most common power device. It was the first truly compact transistor that could be miniaturised and mass-produced for a wide range of uses, revolutionizing the electronics industry and the world economy, having been central to the computer revolution, digital revolution, information revolution, silicon age and information age. MOSFET scaling and miniaturization has been driving the rapid exponential growth of electronic semiconductor technology since the 1960s, and enable high-density integrated circuits (ICs) such as memory chips and microprocessors. The MOSFET is considered to be possibly the most important invention in electronics, as the "workhorse" of the electronics industry and the "base technology" of the late 20th to early 21st centuries, and for having revolutionized modern culture, economy and society across the world.

A key advantage of a MOSFET is that it requires almost no input current to control the load current, when compared with bipolar junction transistors (BJTs). In an enhancement mode MOSFET, voltage applied to the gate terminal can increase the conductivity from the "normally off" state. In a depletion mode MOSFET, voltage applied at the gate can reduce the conductivity from the "normally on" state.[2] MOSFETs are also capable of high scalability (Moore's law and Dennard scaling),[3] with increasing miniaturisation,[4] and can be easily scaled down to smaller dimensions.[5] They also consume much less power, and allow higher density, than bipolar transistors.[6] The MOSFET is also cheaper[7] and has relatively simple processing steps, resulting in a high manufacturing yield.[5]

MOSFETs can either be manufactured as part of MOS integrated circuit chips, or as discrete MOSFET devices (such as a power MOSFET). Since MOSFETs can be made with either p-type or n-type semiconductors (PMOS or NMOS logic, respectively), complementary pairs of MOSFETs can be used to make switching circuits with very low power consumption, in the form of complementary MOS (CMOS) logic. CMOS logic consumes over 7 times less power than NMOS logic,[8] and about 100,000 times less power than bipolar transistor-transistor logic (TTL).[9] The name "metal–oxide–semiconductor" (MOS) typically refers to a metal gate, oxide insulation, and semiconductor (typically silicon).[1] However, the "metal" in the name MOSFET is sometimes a misnomer, because the gate material can also be a layer of polysilicon (polycrystalline silicon). Along with oxide, different dielectric materials can also be used with the aim of obtaining strong channels with smaller applied voltages. The MOS capacitor is also part of the MOSFET structure.

A cross-section through an nMOSFET when the gate voltage VGS is below the threshold for making a conductive channel; there is little or no conduction between the terminals drain and source; the switch is off. When the gate is more positive, it attracts electrons, inducing an n-type conductive channel in the substrate below the oxide, which allows electrons to flow between the n-doped terminals; the switch is on.
Simulation of formation of inversion channel (electron density) and attainment of threshold vol­tage (IV) in a nanowire MOSFET. Note: threshold voltage for this device lies around 0.45 V

Early history[edit]

Background[edit]

The basic principle of the field-effect transistor (FET) was first proposed by Austro-Hungarian physicist Julius Edgar Lilienfeld in 1925.[10] However, his early FET concept was not a practical design.[11] The FET concept was later also theorized by Oskar Heil in the 1930s and William Shockley in the 1940s,[12] but there was no working practical FET built at the time.[11] Shockley's research team initially attempted to build a working FET, by trying to modulate the conductivity of a semiconductor, but they were unsuccessful, mainly due to problems with the surface states, the dangling bond, and the germanium and copper compound materials. In the course of trying to understand the mysterious reasons behind their failure to build a working FET, this led two members of Shockley's team, John Bardeen and Walter Brattain, to instead build a point-contact transistor, the first working transistor, in 1947, which was followed by Shockley's bipolar junction transistor (BJT) in 1948.[13][14] None of these early FET proposals involved thermally oxidized silicon, which later made the MOS transistor possible.[15]

Semiconductor companies initially focused on junction transistors in the early years of the semiconductor industry. However, the junction transistor was a relatively bulky device that was difficult to manufacture on a mass-production basis, which limited it to a number of specialised applications. FETs were theorized as potential alternatives to junction transistors, but researchers were unable to build practical FETs, largely due to the troublesome surface state barrier that prevented the external electric field from penetrating into the material.[16] By the 1950s, researchers had largely given up on the FET concept, and instead focused on BJT technology.[17]

Invention[edit]

Mohamed M. Atalla (left) first proposed the MOSFET. Atalla then invented the first MOSFET with Dawon Kahng (right) in November 1959.

A breakthrough came with the work of Egyptian engineer Mohamed M. Atalla in the late 1950s.[14] He investigated the surface properties of silicon semiconductors at Bell Labs, where he adopted a new method of semiconductor device fabrication, coating a silicon wafer with an insulating layer of silicon oxide, so that electricity could reliably penetrate to the conducting silicon below, overcoming the surface states that prevented electricity from reaching the semiconducting layer. This is known as surface passivation, a method that later became critical to the semiconductor industry as it made possible the mass-production of silicon semiconductor technology, such as integrated circuit (IC) chips.[11][18][19] For the surface passivation process, he developed the method of thermal oxidation, which was a breakthrough in silicon semiconductor technology.[20] The surface passivation method, which substantially reduced the influence of the dangling bond that had prevented Shockley's research team from building a working FET,[14] was presented by Atalla in 1957.[21] Building on the surface passivation method, Atalla developed the metal–oxide–semiconductor (MOS) process,[18] with the use of thermally oxidized silicon.[15][22] He proposed that the MOS process could be used to build the first working silicon FET, which he began working on building with the help of Korean recruit Dawon Kahng.[18]

The MOSFET was invented by Mohamed Atalla and Dawon Kahng in 1959.[12] They fabricated the device in November 1959,[23] and presented it as the "silicon–silicon dioxide field induced surface device" in early 1960,[24] at the Solid-State Device Conference held at Carnegie Mellon University.[25] The device is covered by two patents, each filed separately by Atalla and Kahng in March 1960.[26][27] Operationally and structurally different from the bipolar junction transistor,[28] the MOSFET was made by putting an insulating layer on the surface of the semiconductor and then placing a metallic gate electrode on that. It used crystalline silicon for the semiconductor and a thermally oxidized layer of silicon dioxide for the insulator. The silicon MOSFET did not generate localized electron traps at the interface between the silicon and its native oxide layer, and thus was inherently free from the trapping and scattering of carriers that had impeded the performance of earlier attempts at building a field-effect transistor.

Commercialization[edit]

The MOSFET was the first truly compact transistor that could be miniaturised and mass-produced for a wide range of uses.[16] Despite the breakthrough, the MOSFET was initially overlooked and ignored by Bell Labs in favour of bipolar transistors, which led to Atalla resigning from Bell Labs and joining Hewlett Packard in 1961.[19] However, the MOSFET generated significant interest at RCA Laboratories and Fairchild Semiconductor.[12] In December 1960, Karl Zaininger and Charles Meuller at RCA began fabricating a MOS device based on Atalla's device.[29] Similarly based on Atalla's work,[30] Chih-Tang Sah at Fairchild in late 1960 began building an MOS-controlled tetrode,[12] which he presented in 1961.[31]

In the early 1960s, research programs on MOS technology were established by Fairchild, RCA, General Microelectronics (led by former Fairchild engineer Frank Wanlass) and IBM. In 1963, the first formal public announcement of the MOSFET's existence as a potentially technology was made. It was then first commercialized by General Microelectronics (GMe) in May 1964, followed Fairchild in October 1964. GMe's first MOS contract was with NASA, which used MOSFETs for spacecraft and satellites in the Interplanetary Monitoring Platform (IMP) program and Explorers Program.[32] The early MOSFETs commercialized by GMe and Fairchild were p-channel (PMOS) devices for logic and switching applications.[12]

Importance[edit]

MOS revolution[edit]

The development of the MOSFET led to a revolution in electronics technology, called the MOS revolution[33] or MOSFET revolution.[34] The MOSFET was the first truly compact transistor that could be miniaturised and mass-produced for a wide range of uses.[16] With its rapidly scaling miniaturisation, MOS technology became the focus of RCA, Fairchild, Intel and other semiconductor companies in the 1960s, fuelling the technological and economic growth of the early semiconductor industry based around California (including what later became known as Silicon Valley)[35] as well as Japan.[36] The impact of the MOSFET became commercially significant from the late 1960s onwards.[37] This led to a revolution in the electronics industry, which has since impacted daily life in almost every way.[38] The MOSFET forms the basis of modern electronics,[39] and is the basic element in most modern electronic equipment.[40] It is the most widely used semiconductor device in the world,[41] and the most common transistor in electronics.[11] It has been described as the "workhorse of the electronics industry"[42] and "the base technology" of the late 20th to early 21st centuries.[17]

MOSFET scaling and miniaturization (see List of semiconductor scale examples) has been the primary factor behind the rapid exponential growth of electronic semiconductor technology since the 1960s,[43] as the rapid miniaturization of MOSFETs has been largely responsible for the increasing transistor density, increasing performance and decreasing power consumption of integrated circuit chips and electronic devices since the 1960s.[44] According to Jean-Pierre Colinge, numerous modern technologies would not exist without the MOSFET, such as the modern computer industry, digital telecommunication systems, video games, pocket calculators and digital wristwatches.[45]

The MOSFET has been called the most important transistor,[46] the most important device in the electronics industry,[47] the most important device in the computing industry,[48] one of the most important developments in semiconductor technology,[49] the birth of modern electronics,[50] and possibly the most important invention in electronics.[51] The MOSFET was central to the electronics revolution,[52] microelectronics revolution,[53] silicon revolution,[54][55] and microcomputer revolution,[56] and has been the fundamental building block of modern digital electronics[17] during the digital revolution,[57] information revolution,[58] information age,[59] and silicon age.[54][55] MOSFETs have been the driving force behind the computer revolution, and the technologies enabled by it.[60][61][62] The rapid progress of the electronics industry during the late 20th to early 21st centuries was achieved by rapid MOSFET scaling (Dennard scaling and Moore's law), down to the level of nanoelectronics in the early 21st century.[63]

The MOSFET is the most widely manufactured device in history.[64][65] The MOSFET generates annual sales of $295 billion as of 2015.[66] Between 1960 and 2018, an estimated total of 13 sextillion MOS transistors have been manufactured, accounting for at least 99.9% of all transistors.[64] Digital integrated circuits such as microprocessors and memory devices contain thousands to billions of integrated MOSFET transistors on each device, providing the basic switching functions required to implement logic gates and data storage. There are also memory devices which contain at least a trillion MOS transistors, such as a 256 GB microSD memory card, larger than the number of stars in the Milky Way galaxy.[42] As of 2010, the operating principles of modern MOSFETs have remained largely the same as the original MOSFET first demonstrated by Mohamed Atalla and Dawon Kahng in 1960.[67][68]

MOS integrated circuit chips as well as discrete power MOSFETs are fundamental to the Internet, and the communications infrastructure that enables the Internet.[69][70] MOSFETs are also fundamental to digital wireless telecommunication networks,[71][72] and most of the essential elements of mobile networks use MOSFETs.[72] Advances in MOS technology has been the most important contributing factor in the rapid rise of network bandwidth in telecommunications networks, with bandwidth doubling every 18 months, from bits per second to terabits per second.[73]

The mass-production of silicon MOSFETs and MOS integrated circuit chips, along with continuous MOSFET scaling miniaturization at an exponential pace (as predicted by Moore's law), has led to revolutionary changes in technology, economy, culture and thinking.[54] The US Patent and Trademark Office calls the MOSFET a "groundbreaking invention that transformed life and culture around the world"[60] and the Computer History Museum credits it with "irrevocably changing the human experience."[17] The MOSFET was also the basis for Nobel Prize winning breakthroughs such as the quantum Hall effect[74] and the charge-coupled device (CCD),[75] yet there was never any Nobel Prize given for the MOSFET itself.[76] In 2018, the Royal Swedish Academy of Sciences which awards the science Nobel Prizes acknowledged that the invention of the MOSFET by Atalla and Kahng was one of the most important inventions in microelectronics and in information and communications technology (ICT).[77] The MOSFET is also included on the list of IEEE milestones in electronics,[78] and its inventors Mohamed Atalla and Dawon Kahng entered the National Inventors Hall of Fame in 2009.[11][18]

Common applications[edit]

The MOSFET is by far the most widely used transistor in both digital circuits and analog circuits, and it is the backbone of modern electronics.[79] It is the basis for numerous modern technologies,[45] and is commonly used for a wide range of applications.[44] Common applications of MOS technology include the following.

Composition[edit]

Photomicrograph of two metal-gate MOSFETs in a test pattern. Probe pads for two gates and three source/drain nodes are labeled.

Usually the semiconductor of choice is silicon. Recently, some chip manufacturers, most notably IBM and Intel, have started using a chemical compound of silicon and germanium (SiGe) in MOSFET channels. Unfortunately, many semiconductors with better electrical properties than silicon, such as gallium arsenide, do not form good semiconductor-to-insulator interfaces, and thus are not suitable for MOSFETs. Research continues[when?] on creating insulators with acceptable electrical characteristics on other semiconductor materials.

To overcome the increase in power consumption due to gate current leakage, a high-κ dielectric is used instead of silicon dioxide for the gate insulator, while polysilicon is replaced by metal gates (e.g. Intel, 2009[192]).

The gate is separated from the channel by a thin insulating layer, traditionally of silicon dioxide and later of silicon oxynitride. Some companies have started to introduce a high-κ dielectric and metal gate combination in the 45 nanometer node.

When a voltage is applied between the gate and body terminals, the electric field generated penetrates through the oxide and creates an inversion layer or channel at the semiconductor-insulator interface. The inversion layer provides a channel through which current can pass between source and drain terminals. Varying the voltage between the gate and body modulates the conductivity of this layer and thereby controls the current flow between drain and source. This is known as enhancement mode.

Operation[edit]

Metal–oxide–semiconductor structure on p-type silicon

Metal–oxide–semiconductor structure[edit]

The traditional metal–oxide–semiconductor (MOS) structure is obtained by growing a layer of silicon dioxide (SiO
2
) on top of a silicon substrate, commonly by thermal oxidation and depositing a layer of metal or polycrystalline silicon (the latter is commonly used). As the silicon dioxide is a dielectric material, its structure is equivalent to a planar capacitor, with one of the electrodes replaced by a semiconductor.

When a voltage is applied across a MOS structure, it modifies the distribution of charges in the semiconductor. If we consider a p-type semiconductor (with the density of acceptors, p the density of holes; p = NA in neutral bulk), a positive voltage, , from gate to body (see figure) creates a depletion layer by forcing the positively charged holes away from the gate-insulator/semiconductor interface, leaving exposed a carrier-free region of immobile, negatively charged acceptor ions (see doping (semiconductor)). If is high enough, a high concentration of negative charge carriers forms in an inversion layer located in a thin layer next to the interface between the semiconductor and the insulator.

Conventionally, the gate voltage at which the volume density of electrons in the inversion layer is the same as the volume density of holes in the body is called the threshold voltage. When the voltage between transistor gate and source (VGS) exceeds the threshold voltage (Vth), the difference is known as overdrive voltage.

This structure with p-type body is the basis of the n-type MOSFET, which requires the addition of n-type source and drain regions.

MOS capacitors and band diagrams[edit]

The MOS capacitor structure is the heart of the MOSFET. Consider a MOS capacitor where the silicon base is of p-type. If a positive voltage is applied at the gate, holes which are at the surface of the p-type substrate will be repelled by the electric field generated by the voltage applied. At first, the holes will simply be repelled and what will remain on the surface will be immobile (negative) atoms of the acceptor type, which creates a depletion region on the surface. Remember that a hole is created by an acceptor atom, e.g. Boron, which has one less electron than Silicon. One might ask how can holes be repelled if they are actually non-entities? The answer is that what really happens is not that a hole is repelled, but electrons are attracted by the positive field, and fill these holes, creating a depletion region where no charge carriers exist because the electron is now fixed onto the atom and immobile.

As the voltage at the gate increases, there will be a point at which the surface above the depletion region will be converted from p-type into n-type, as electrons from the bulk area will start to get attracted by the larger electric field. This is known as inversion. The threshold voltage at which this conversion happens is one of the most important parameters in a MOSFET.

In the case of a p-type bulk, inversion happens when the intrinsic energy level at the surface becomes smaller than the Fermi level at the surface. One can see this from a band diagram. Remember that the Fermi level defines the type of semiconductor in discussion. If the Fermi level is equal to the Intrinsic level, the semiconductor is of intrinsic, or pure type. If the Fermi level lies closer to the conduction band (valence band) then the semiconductor type will be of n-type (p-type). Therefore, when the gate voltage is increased in a positive sense (for the given example), this will "bend" the intrinsic energy level band so that it will curve downwards towards the valence band. If the Fermi level lies closer to the valence band (for p-type), there will be a point when the Intrinsic level will start to cross the Fermi level and when the voltage reaches the threshold voltage, the intrinsic level does cross the Fermi level, and that is what is known as inversion. At that point, the surface of the semiconductor is inverted from p-type into n-type. Remember that as said above, if the Fermi level lies above the Intrinsic level, the semiconductor is of n-type, therefore at Inversion, when the Intrinsic level reaches and crosses the Fermi level (which lies closer to the valence band), the semiconductor type changes at the surface as dictated by the relative positions of the Fermi and Intrinsic energy levels.

Structure and channel formation[edit]

Channel formation in nMOS MOSFET shown as band diagram: Top panels: An applied gate voltage bends bands, depleting holes from surface (left). The charge inducing the bending is balanced by a layer of negative acceptor-ion charge (right). Bottom panel: A larger applied voltage further depletes holes but conduction band lowers enough in energy to populate a conducting channel
C–V profile for a bulk MOSFET with different oxide thickness. The leftmost part of the curve corresponds to accumulation. The valley in the middle corresponds to depletion. The curve on the right corresponds to inversion

A MOSFET is based on the modulation of charge concentration by a MOS capacitance between a body electrode and a gate electrode located above the body and insulated from all other device regions by a gate dielectric layer. If dielectrics other than an oxide are employed, the device may be referred to as a metal-insulator-semiconductor FET (MISFET). Compared to the MOS capacitor, the MOSFET includes two additional terminals (source and drain), each connected to individual highly doped regions that are separated by the body region. These regions can be either p or n type, but they must both be of the same type, and of opposite type to the body region. The source and drain (unlike the body) are highly doped as signified by a "+" sign after the type of doping.

If the MOSFET is an n-channel or nMOS FET, then the source and drain are n+ regions and the body is a p region. If the MOSFET is a p-channel or pMOS FET, then the source and drain are p+ regions and the body is a n region. The source is so named because it is the source of the charge carriers (electrons for n-channel, holes for p-channel) that flow through the channel; similarly, the drain is where the charge carriers leave the channel.

The occupancy of the energy bands in a semiconductor is set by the position of the Fermi level relative to the semiconductor energy-band edges.

With sufficient gate voltage, the valence band edge is driven far from the Fermi level, and holes from the body are driven away from the gate.

At larger gate bias still, near the semiconductor surface the conduction band edge is brought close to the Fermi level, populating the surface with electrons in an inversion layer or n-channel at the interface between the p region and the oxide. This conducting channel extends between the source and the drain, and current is conducted through it when a voltage is applied between the two electrodes. Increasing the voltage on the gate leads to a higher electron density in the inversion layer and therefore increases the current flow between the source and drain. For gate voltages below the threshold value, the channel is lightly populated, and only a very small subthreshold leakage current can flow between the source and the drain.

When a negative gate–source voltage is applied, it creates a p-channel at the surface of the n region, analogous to the n-channel case, but with opposite polarities of charges and voltages. When a voltage less negative than the threshold value (a negative voltage for the p-channel) is applied between gate and source, the channel disappears and only a very small subthreshold current can flow between the source and the drain. The device may comprise a silicon on insulator device in which a buried oxide is formed below a thin semiconductor layer. If the channel region between the gate dielectric and the buried oxide region is very thin, the channel is referred to as an ultrathin channel region with the source and drain regions formed on either side in or above the thin semiconductor layer. Other semiconductor materials may be employed. When the source and drain regions are formed above the channel in whole or in part, they are referred to as raised source/drain regions.

Comparison of n- and p-type MOSFETs[193]
Parameter nMOSFET pMOSFET
Source/drain type n-type p-type
Channel type
(MOS capacitor)
n-type p-type
Gate
type
Polysilicon n+ p+
Metal φm ~ Si conduction band φm ~ Si valence band
Well type p-type n-type
Threshold voltage, Vth
  • Positive (enhancement)
  • Negative (depletion)
  • Negative (enhancement)
  • Positive (depletion)
Band-bending Downwards Upwards
Inversion layer carriers Electrons Holes
Substrate type p-type n-type

Modes of operation[edit]

Source tied to the body to ensure no body bias:
top left: Subthreshold, top right: Ohmic mode, bottom left: Active mode at onset of pinch-off, bottom right: Active mode well into pinch-off – channel length modulation evident
Example application of an n-channel MOSFET. When the switch is pushed, the LED lights up.[194]

The operation of a MOSFET can be separated into three different modes, depending on the voltages at the terminals. In the following discussion, a simplified algebraic model is used.[195] Modern MOSFET characteristics are more complex than the algebraic model presented here.[196]

For an enhancement-mode, n-channel MOSFET, the three operational modes are:

Cutoff, subthreshold, and weak-inversion mode

When VGS < Vth:

where is gate-to-source bias and is the threshold voltage of the device.

According to the basic threshold model, the transistor is turned off, and there is no conduction between drain and source. A more accurate model considers the effect of thermal energy on the Fermi–Dirac distribution of electron energies which allow some of the more energetic electrons at the source to enter the channel and flow to the drain. This results in a subthreshold current that is an exponential function of gate–source voltage. While the current between drain and source should ideally be zero when the transistor is being used as a turned-off switch, there is a weak-inversion current, sometimes called subthreshold leakage.

In weak inversion where the source is tied to bulk, the current varies exponentially with as given approximately by:[197][198]

where = current at , the thermal voltage and the slope factor n is given by:

with = capacitance of the depletion layer and = capacitance of the oxide layer. This equation is generally used, but is only an adequate approximation for the source tied to the bulk. For the source not tied to the bulk, the subthreshold equation for drain current in saturation is[199][200]

where the is the channel divider that is given by:

with = capacitance of the depletion layer and = capacitance of the oxide layer. In a long-channel device, there is no drain voltage dependence of the current once , but as channel length is reduced drain-induced barrier lowering introduces drain voltage dependence that depends in a complex way upon the device geometry (for example, the channel doping, the junction doping and so on). Frequently, threshold voltage Vth for this mode is defined as the gate voltage at which a selected value of current ID0 occurs, for example, ID0 = 1 μA, which may not be the same Vth-value used in the equations for the following modes.

Some micropower analog circuits are designed to take advantage of subthreshold conduction.[201][202][203] By working in the weak-inversion region, the MOSFETs in these circuits deliver the highest possible transconductance-to-current ratio, namely: , almost that of a bipolar transistor.[204]

The subthreshold I–V curve depends exponentially upon threshold voltage, introducing a strong dependence on any manufacturing variation that affects threshold voltage; for example: variations in oxide thickness, junction depth, or body doping that change the degree of drain-induced barrier lowering. The resulting sensitivity to fabricational variations complicates optimization for leakage and performance.[205][206]

MOSFET drain current vs. drain-to-source voltage for several values of ; the boundary between linear (Ohmic) and saturation (active) modes is indicated by the upward curving parabola
Cross section of a MOSFET operating in the linear (Ohmic) region; strong inversion region present even near drain
Cross section of a MOSFET operating in the saturation (active) region; channel exhibits channel pinching near drain
Triode mode or linear region (also known as the ohmic mode[207][208])

When VGS > Vth and VDS < VGS − Vth:

The transistor is turned on, and a channel has been created which allows current between the drain and the source. The MOSFET operates like a resistor, controlled by the gate voltage relative to both the source and drain voltages. The current from drain to source is modeled as:

where is the charge-carrier effective mobility, is the gate width, is the gate length and is the gate oxide capacitance per unit area. The transition from the exponential subthreshold region to the triode region is not as sharp as the equations suggest.

Saturation or active mode[209][210]

When VGS > Vth and VDS ≥ (VGS – Vth):

The switch is turned on, and a channel has been created, which allows current between the drain and source. Since the drain voltage is higher than the source voltage, the electrons spread out, and conduction is not through a narrow channel but through a broader, two- or three-dimensional current distribution extending away from the interface and deeper in the substrate. The onset of this region is also known as pinch-off to indicate the lack of channel region near the drain. Although the channel does not extend the full length of the device, the electric field between the drain and the channel is very high, and conduction continues. The drain current is now weakly dependent upon drain voltage and controlled primarily by the gate–source voltage, and modeled approximately as:

The additional factor involving λ, the channel-length modulation parameter, models current dependence on drain voltage due to the channel length modulation, effectively similar to the Early effect seen in bipolar devices. According to this equation, a key design parameter, the MOSFET transconductance is:

where the combination Vov = VGS − Vth is called the overdrive voltage,[211] and where VDSsat = VGS − Vth accounts for a small discontinuity in which would otherwise appear at the transition between the triode and saturation regions.

Another key design parameter is the MOSFET output resistance rout given by:

.

rout is the inverse of gDS where . ID is the expression in saturation region.

If λ is taken as zero, an infinite output resistance of the device results that leads to unrealistic circuit predictions, particularly in analog circuits.

As the channel length becomes very short, these equations become quite inaccurate. New physical effects arise. For example, carrier transport in the active mode may become limited by velocity saturation. When velocity saturation dominates, the saturation drain current is more nearly linear than quadratic in VGS. At even shorter lengths, carriers transport with near zero scattering, known as quasi-ballistic transport. In the ballistic regime, the carriers travel at an injection velocity that may exceed the saturation velocity and approaches the Fermi velocity at high inversion charge density. In addition, drain-induced barrier lowering increases off-state (cutoff) current and requires an increase in threshold voltage to compensate, which in turn reduces the saturation current.

Body effect[edit]

Band diagram showing body effect. VSB splits Fermi levels Fn for electrons and Fp for holes, requiring larger VGB to populate the conduction band in an nMOS MOSFET

The occupancy of the energy bands in a semiconductor is set by the position of the Fermi level relative to the semiconductor energy-band edges. Application of a source-to-substrate reverse bias of the source-body pn-junction introduces a split between the Fermi levels for electrons and holes, moving the Fermi level for the channel further from the band edge, lowering the occupancy of the channel. The effect is to increase the gate voltage necessary to establish the channel, as seen in the figure. This change in channel strength by application of reverse bias is called the 'body effect'.

Simply put, using an nMOS example, the gate-to-body bias VGB positions the conduction-band energy levels, while the source-to-body bias VSB positions the electron Fermi level near the interface, deciding occupancy of these levels near the interface, and hence the strength of the inversion layer or channel.

The body effect upon the channel can be described using a modification of the threshold voltage, approximated by the following equation:

where VTB is the threshold voltage with substrate bias present, and VT0 is the zero-VSB value of threshold voltage, is the body effect parameter, and 2φB is the approximate potential drop between surface and bulk across the depletion layer when VSB = 0 and gate bias is sufficient to ensure that a channel is present.[212] As this equation shows, a reverse bias VSB > 0 causes an increase in threshold voltage VTB and therefore demands a larger gate voltage before the channel populates.

The body can be operated as a second gate, and is sometimes referred to as the "back gate"; the body effect is sometimes called the "back-gate effect".[213]

Circuit symbols[edit]

A variety of symbols are used for the MOSFET. The basic design is generally a line for the channel with the source and drain leaving it at right angles and then bending back at right angles into the same direction as the channel. Sometimes three line segments are used for enhancement mode and a solid line for depletion mode (see depletion and enhancement modes). Another line is drawn parallel to the channel for the gate.

The bulk or body connection, if shown, is shown connected to the back of the channel with an arrow indicating pMOS or nMOS. Arrows always point from P to N, so an NMOS (N-channel in P-well or P-substrate) has the arrow pointing in (from the bulk to the channel). If the bulk is connected to the source (as is generally the case with discrete devices) it is sometimes angled to meet up with the source leaving the transistor. If the bulk is not shown (as is often the case in IC design as they are generally common bulk) an inversion symbol is sometimes used to indicate PMOS, alternatively an arrow on the source may be used in the same way as for bipolar transistors (out for nMOS, in for pMOS).

Comparison of enhancement-mode and depletion-mode MOSFET symbols, along with JFET symbols. The orientation of the symbols, (most significantly the position of source relative to drain) is such that more positive voltages appear higher on the page than less positive voltages, implying current flowing "down" the page:[214][215][216]

P-channel JFET P-Channel Labelled.svg IGFET P-Ch Enh Labelled.svg IGFET P-Ch Enh Labelled simplified.svg Mosfet P-Ch Sedra.svg IGFET P-Ch Dep Labelled.svg
N-channel JFET N-Channel Labelled.svg IGFET N-Ch Enh Labelled.svg IGFET N-Ch Enh Labelled simplified.svg Mosfet N-Ch Sedra.svg IGFET N-Ch Dep Labelled.svg
JFET MOSFET enh. MOSFET enh. (no bulk) MOSFET dep.

In schematics where G, S, D are not labeled, the detailed features of the symbol indicate which terminal is source and which is drain. For enhancement-mode and depletion-mode MOSFET symbols (in columns two and five), the source terminal is the one connected to the triangle. Additionally, in this diagram, the gate is shown as an "L" shape, whose input leg is closer to S than D, also indicating which is which. However, these symbols are often drawn with a "T" shaped gate (as elsewhere on this page), so it is the triangle which must be relied upon to indicate the source terminal.

For the symbols in which the bulk, or body, terminal is shown, it is here shown internally connected to the source (i.e., the black triangles in the diagrams in columns 2 and 5). This is a typical configuration, but by no means the only important configuration. In general, the MOSFET is a four-terminal device, and in integrated circuits many of the MOSFETs share a body connection, not necessarily connected to the source terminals of all the transistors.

Types of MOSFET[edit]

PMOS and NMOS logic[edit]

P-type MOS (PMOS) logic uses p-channel MOSFETs to implement logic gates and other digital circuits. N-type MOS (NMOS) logic uses n-channel MOSFETs to implement logic gates and other digital circuits.

For devices of equal current driving capability, n-channel MOSFETs can be made smaller than p-channel MOSFETs, due to p-channel charge carriers (holes) having lower mobility than do n-channel charge carriers (electrons), and producing only one type of MOSFET on a silicon substrate is cheaper and technically simpler. These were the driving principles in the design of NMOS logic which uses n-channel MOSFETs exclusively. However, neglecting leakage current, unlike CMOS logic, NMOS logic consumes power even when no switching is taking place.

Mohamed Atalla and Dawon Kahng originally demonstrated both pMOS and nMOS devices with 20 µm and then 10 µm gate lengths in 1960.[19][217] Their original MOSFET devices also had a gate oxide thickness of 100 nm.[218] However, the nMOS devices were impractical, and only the pMOS type were practical working devices.[19] A more practical NMOS process was developed several years later. NMOS was initially faster than CMOS, thus NMOS was more widely used for computers in the 1970s.[8] With advances in technology, CMOS logic displaced NMOS logic in the mid-1980s to become the preferred process for digital chips.

Complementary MOS (CMOS)[edit]

The MOSFET is used in digital complementary metal–oxide–semiconductor (CMOS) logic,[219] which uses p- and n-channel MOSFETs as building blocks. Overheating is a major concern in integrated circuits since ever more transistors are packed into ever smaller chips. CMOS logic reduces power consumption because no current flows (ideally), and thus no power is consumed, except when the inputs to logic gates are being switched. CMOS accomplishes this current reduction by complementing every nMOSFET with a pMOSFET and connecting both gates and both drains together. A high voltage on the gates will cause the nMOSFET to conduct and the pMOSFET not to conduct and a low voltage on the gates causes the reverse. During the switching time as the voltage goes from one state to another, both MOSFETs will conduct briefly. This arrangement greatly reduces power consumption and heat generation.

CMOS was developed by Chih-Tang Sah and Frank Wanlass at Fairchild Semiconductor in 1963.[220] CMOS had lower power consumption, but was initially slower than NMOS, which was more widely used for computers in the 1970s. In 1978, Hitachi introduced the twin-well CMOS process, which allowed CMOS to match the performance of NMOS with less power consumption. The twin-well CMOS process eventually overtook NMOS as the most common semiconductor manufacturing process for computers in the 1980s.[8]

Depletion-mode[edit]

There are depletion-mode MOSFET devices, which are less commonly used than the standard enhancement-mode devices already described. These are MOSFET devices that are doped so that a channel exists even with zero voltage from gate to source. To control the channel, a negative voltage is applied to the gate (for an n-channel device), depleting the channel, which reduces the current flow through the device. In essence, the depletion-mode device is equivalent to a normally closed (on) switch, while the enhancement-mode device is equivalent to a normally open (off) switch.[221]

Due to their low noise figure in the RF region, and better gain, these devices are often preferred to bipolars in RF front-ends such as in TV sets.

Depletion-mode MOSFET families include BF960 by Siemens and Telefunken, and the BF980 in the 1980s by Philips (later to become NXP Semiconductors), whose derivatives are still used in AGC and RF mixer front-ends.

Metal-insulator-semiconductor field-effect transistor (MISFET)[edit]

Metal-insulator-semiconductor field-effect-transistor,[222][223][224] or MISFET, is a more general term than MOSFET and a synonym to insulated-gate field-effect transistor (IGFET). All MOSFETs are MISFETs, but not all MISFETs are MOSFETs.

The gate dielectric insulator in a MISFET is silicon dioxide in a MOSFET, but other materials can also be employed. The gate dielectric lies directly below the gate electrode and above the channel of the MISFET. The term metal is historically used for the gate material, even though now it is usually highly doped polysilicon or some other non-metal.

Insulator types may be:

Floating-gate MOSFET (FGMOS)[edit]

The floating-gate MOSFET (FGMOS) is a type of MOSFET where the gate is electrically isolated, creating a floating node in DC and a number of secondary gates or inputs are deposited above the floating gate (FG) and are electrically isolated from it. The first report of a floating-gate MOSFET (FGMOS) was made by Dawon Kahng (co-inventor of the original MOSFET) and Simon Sze in 1967.[226]

The FGMOS is commonly used as a floating-gate memory cell, the digital storage element in EPROM, EEPROM and flash memories. Other uses of the FGMOS include a neuronal computational element in neural networks, analog storage element, digital potentiometers and single-transistor DACs.

Power MOSFET[edit]

Two power MOSFETs in D2PAK surface-mount packages. Operating as switches, each of these components can sustain a blocking voltage of 120 V in the off state, and can conduct a con­ti­nuous current of 30 A in the on state, dissipating up to about 100 W and controlling a load of over 2000 W. A matchstick is pictured for scale.
Cross section of a power MOSFET, with square cells. A typical transistor is constituted of several thousand cells

Power MOSFETs have a different structure.[227] As with most power devices, the structure is vertical and not planar. Using a vertical structure, it is possible for the transistor to sustain both high blocking voltage and high current. The voltage rating of the transistor is a function of the doping and thickness of the N-epitaxial layer (see cross section), while the current rating is a function of the channel width (the wider the channel, the higher the current). In a planar structure, the current and breakdown voltage ratings are both a function of the channel dimensions (respectively width and length of the channel), resulting in inefficient use of the "silicon estate". With the vertical structure, the component area is roughly proportional to the current it can sustain, and the component thickness (actually the N-epitaxial layer thickness) is proportional to the breakdown voltage.[228]

Power MOSFETs with lateral structure are mainly used in high-end audio amplifiers and high-power PA systems. Their advantage is a better behaviour in the saturated region (corresponding to the linear region of a bipolar transistor) than the vertical MOSFETs. Vertical MOSFETs are designed for switching applications.[229]

The power MOSFET, which is commonly used in power electronics, was developed in the early 1970s.[230] The power MOSFET enables low gate drive power, fast switching speed, and advanced paralleling capability.[231]

Double-diffused metal–oxide–semiconductor (DMOS)[edit]

There are VDMOS (vertical double-diffused metal oxide semiconductor) and LDMOS (lateral double-diffused metal oxide semiconductor). Most power MOSFETs are made using this technology.

MOS capacitor[edit]

The MOS capacitor is part of the MOSFET structure, where the MOS capacitor is flanked by two p-n junctions.[232] The MOS capacitor is widely used as a storage capacitor in memory chips, and as the basic building block of the charge-coupled device (CCD) in image sensor technology.[233] In DRAM (dynamic random-access memory), each memory cell typically consists of a MOSFET and MOS capacitor.[234]

Thin-film transistor (TFT)[edit]

The thin-film transistor (TFT) is a type of MOSFET distinct from the standard bulk MOSFET.[125] The first TFT was invented by Paul K. Weimer at RCA in 1962, building on the earlier work of Atalla and Kahng on MOSFETs.[235]

The idea of a TFT-based liquid-crystal display (LCD) was conceived by Bernard Lechner of RCA Laboratories in 1968.[236] Lechner, F. J. Marlowe, E. O. Nester and J. Tults demonstrated the concept in 1968 with an 18x2 matrix dynamic scattering LCD that used standard discrete MOSFETs, as TFT performance was not adequate at the time.[237]

Bipolar-MOS transistors[edit]

BiCMOS is an integrated circuit that combines BJT and complementary MOS (CMOS) transistors on a single chip.[238]

The insulated-gate bipolar transistor (IGBT) is a power transistor with characteristics of both a MOSFET and bipolar junction transistor (BJT).[239]

MOS sensors[edit]

A number of MOSFET sensors have been developed, for measuring physical, chemical, biological and environmental parameters.[129] The earliest MOSFET sensors include the open-gate FET (OGFET) introduced by Johannessen in 1970,[129] the ion-sensitive field-effect transistor (ISFET) invented by Piet Bergveld in 1970,[240] the adsorption FET (ADFET) patented by P.F. Cox in 1974, and a hydrogen-sensitive MOSFET demonstrated by I. Lundstrom, M.S. Shivaraman, C.S. Svenson and L. Lundkvist in 1975.[129] The ISFET is a special type of MOSFET with a gate at a certain distance,[129] and where the metal gate is replaced by an ion-sensitive membrane, electrolyte solution and reference electrode.[98]

By the mid-1980s, numerous other MOSFET sensors had been developed, including the gas sensor FET (GASFET), surface accessible FET (SAFET), charge flow transistor (CFT), pressure sensor FET (PRESSFET), chemical field-effect transistor (ChemFET), reference ISFET (REFET), biosensor FET (BioFET), enzyme-modified FET (ENFET) and immunologically modified FET (IMFET).[129] By the early 2000s, BioFET types such as the DNA field-effect transistor (DNAFET), gene-modified FET (GenFET) and cell-potential BioFET (CPFET) had been developed.[98]

The two main types of image sensors used in digital imaging technology are the charge-coupled device (CCD) and the active-pixel sensor (CMOS sensor). Both CCD and CMOS sensors are based on MOS technology, with the CCD based on MOS capacitors and the CMOS sensor based on MOS transistors.[75]

Multi-gate field-effect transistor (MuGFET)[edit]

A FinFET (fin field-effect transistor), a type of multi-gate MOSFET.

The dual-gate MOSFET (DGMOS) has a tetrode configuration, where both gates control the current in the device. It is commonly used for small-signal devices in radio frequency applications where biasing the drain-side gate at constant potential reduces the gain loss caused by Miller effect, replacing two separate transistors in cascode configuration. Other common uses in RF circuits include gain control and mixing (frequency conversion). The tetrode description, though accurate, does not replicate the vacuum-tube tetrode. Vacuum-tube tetrodes, using a screen grid, exhibit much lower grid-plate capacitance and much higher output impedance and voltage gains than triode vacuum tubes. These improvements are commonly an order of magnitude (10 times) or considerably more. Tetrode transistors (whether bipolar junction or field-effect) do not exhibit improvements of such a great degree.

The FinFET is a double-gate silicon-on-insulator device, one of a number of geometries being introduced to mitigate the effects of short channels and reduce drain-induced barrier lowering. The fin refers to the narrow channel between source and drain. A thin insulating oxide layer on either side of the fin separates it from the gate. SOI FinFETs with a thick oxide on top of the fin are called double-gate and those with a thin oxide on top as well as on the sides are called triple-gate FinFETs.[241][242]

A double-gate MOSFET transistor was first demonstrated in 1984 by Electrotechnical Laboratory researchers Toshihiro Sekigawa and Yutaka Hayashi.[243][244] A GAAFET (gate-all-around MOSFET), a type of multi-gate non-planar 3D transistor, was first demonstrated in 1988 by a Toshiba research team including Fujio Masuoka, H. Takato and K. Sunouchi.[245][246] The FinFET (fin field-effect transistor), a type of 3D non-planar double-gate MOSFET, originated from the research of Digh Hisamoto and his team at Hitachi Central Research Laboratory in 1989.[247][248] The development of nanowire multi-gate MOSFETs have since become fundamental to nanoelectronics.[153]

Radiation-hardened-by-design (RHBD)[edit]

Semiconductor sub-micrometer and nanometer electronic circuits are the primary concern for operating within the normal tolerance in harsh radiation environments like outer space. One of the design approaches for making a radiation-hardened-by-design (RHBD) device is enclosed-layout-transistor (ELT). Normally, the gate of the MOSFET surrounds the drain, which is placed in the center of the ELT. The source of the MOSFET surrounds the gate. Another RHBD MOSFET is called H-Gate. Both of these transistors have very low leakage current with respect to radiation. However, they are large in size and take more space on silicon than a standard MOSFET. In older STI (shallow trench isolation) designs, radiation strikes near the silicon oxide region cause the channel inversion at the corners of the standard MOSFET due to accumulation of radiation induced trapped charges. If the charges are large enough, the accumulated charges affect STI surface edges along the channel near the channel interface (gate) of the standard MOSFET. Thus the device channel inversion occurs along the channel edges and the device creates an off-state leakage path, causing the device to turn on. So the reliability of circuits degrades severely. The ELT offers many advantages. These advantages include improvement of reliability by reducing unwanted surface inversion at the gate edges that occurs in the standard MOSFET. Since the gate edges are enclosed in ELT, there is no gate oxide edge (STI at gate interface), and thus the transistor off-state leakage is reduced considerably. Low-power microelectronic circuits including computers, communication devices and monitoring systems in the space shuttle and satellites are very different to what is used on earth. They require radiation (high-speed atomic particles like proton and neutron, solar flare magnetic energy dissipation in Earth's space, energetic cosmic rays like X-ray, gamma ray etc.) tolerant circuits. These special electronics are designed by applying different techniques using RHBD MOSFETs to ensure safer journeys and space-walks for astronauts.

Applications[edit]

Discrete MOSFET devices are widely used in applications such as switch mode power supplies, variable-frequency drives and other power electronics applications where each device may be switching thousands of watts. Radio-frequency amplifiers up to the UHF spectrum use MOSFET transistors as analog signal and power amplifiers. Radio systems also use MOSFETs as oscillators, or mixers to convert frequencies. MOSFET devices are also applied in audio-frequency power amplifiers for public address systems, sound reinforcement and home and automobile sound systems.[citation needed]

MOS integrated circuit[edit]

The MOSFET is the most widely used type of transistor and the most critical device component in integrated circuit (IC) chips.[137] The monolithic integrated circuit chip was enabled by the surface passivation process, which electrically stabilized silicon surfaces via thermal oxidation, making it possible to fabricate monolithic integrated circuit chips using silicon. The surface passivation process was developed by Mohamed M. Atalla at Bell Labs in 1957. This was the basis for the planar process, developed by Jean Hoerni at Fairchild Semiconductor in early 1959, which was critical to the invention of the monolithic integrated circuit chip by Robert Noyce later in 1959.[249][250][30] The same year,[12] Atalla used his surface passivation process to invent the MOSFET with Dawon Kahng at Bell Labs.[18][11] This was followed by the development of clean rooms to reduce contamination to levels never before thought necessary, and coincided with the development of photolithography[251] which, along with surface passivation and the planar process, allowed circuits to be made in few steps.

Mohamed Atalla first proposed the concept of the MOS integrated circuit (MOS IC) chip in 1960, noting that the MOSFET's ease of fabrication made it useful for integrated circuits.[16] This was re-iterated by Dawon Kahng in 1961.[23] The SiSiO2 system possessed the technical attractions of low cost of production (on a per circuit basis) and ease of integration. These two factors, along with its rapidly scaling miniaturization and low energy consumption, led to the MOSFET becoming the most widely used type of transistor in IC chips.

The earliest experimental MOS IC to be demonstrated was a 16-transistor chip built by Fred Heiman and Steven Hofstein at RCA in 1962.[7] General Microelectronics later introduced the first commercial MOS integrated circuits in 1964, consisting of 120 p-channel transistors.[252] It was a 20-bit shift register, developed by Robert Norman[7] and Frank Wanlass.[253] In 1967, Bell Labs researchers Robert Kerwin, Donald Klein and John Sarace developed the self-aligned gate (silicon-gate) MOS transistor, which Fairchild Semiconductor researchers Federico Faggin and Tom Klein used to develop the first silicon-gate MOS IC.[254]

Large-scale integration (LSI)[edit]

With its high scalability,[3] and much lower power consumption and higher density than bipolar junction transistors,[6] the MOSFET made it possible to build high-density IC chips.[1] By 1964, MOS chips had reached higher transistor density and lower manufacturing costs than bipolar chips. MOS chips further increased in complexity at a rate predicted by Moore's law, leading to large-scale integration (LSI) with hundreds of MOSFETs on a chip by the late 1960s.[139] MOS technology enabled the integration of more than 10,000 transistors on a single LSI chip by the early 1970s,[100] before later enabling very large-scale integration (VLSI).[5][107]

One of the earliest influential consumer electronic products enabled by MOS LSI circuits was the electronic pocket calculator,[100] as MOS LSI technology enabled large amounts of computational capability in small packages.[111] In 1965, the Victor 3900 desktop calculator was the first MOS LSI calculator, with 29 MOS LSI chips.[255] In 1967 the Texas Instruments Cal-Tech was the first prototype electronic handheld calculator, with three MOS LSI chips, and it was later released as the Canon Pocketronic in 1970.[256] The Sharp QT-8D desktop calculator was the first mass-produced LSI MOS calculator in 1969,[255] and the Sharp EL-8 which used four MOS LSI chips was the first commercial electronic handheld calculator in 1970.[256] The first true electronic pocket calculator was the Busicom LE-120A HANDY LE, which used a single MOS LSI calculator-on-a-chip from Mostek, and was released in 1971.[256] By 1972, MOS LSI circuits were commercialized for numerous other applications.[91]

Microprocessors[edit]

The MOSFET is the basis of every microprocessor,[42] and was responsible for the invention of the microprocessor.[257] The origins of both the microprocessor and the microcontroller can be traced back to the invention and development of MOS technology. The application of MOS LSI chips to computing was the basis for the first microprocessors, as engineers began recognizing that a complete computer processor could be contained on a single MOS LSI chip.[139]

The earliest microprocessors were all MOS chips, built with MOS LSI circuits. The first multi-chip microprocessors, the Four-Phase Systems AL1 in 1969 and the Garrett AiResearch MP944 in 1970, were developed with multiple MOS LSI chips. The first commercial single-chip microprocessor, the Intel 4004, was developed by Federico Faggin, using his silicon-gate MOS IC technology, with Intel engineers Marcian Hoff and Stan Mazor, and Busicom engineer Masatoshi Shima.[258] With the arrival of CMOS microprocessors in 1975, the term "MOS microprocessors" began to refer to chips fabricated entirely from PMOS logic or fabricated entirely from NMOS logic, contrasted with "CMOS microprocessors" and "bipolar bit-slice processors".[259]

CMOS circuits[edit]

Digital[edit]

The growth of digital technologies like the microprocessor has provided the motivation to advance MOSFET technology faster than any other type of silicon-based transistor.[260] A big advantage of MOSFETs for digital switching is that the oxide layer between the gate and the channel prevents DC current from flowing through the gate, further reducing power consumption and giving a very large input impedance. The insulating oxide between the gate and channel effectively isolates a MOSFET in one logic stage from earlier and later stages, which allows a single MOSFET output to drive a considerable number of MOSFET inputs. Bipolar transistor-based logic (such as TTL) does not have such a high fanout capacity. This isolation also makes it easier for the designers to ignore to some extent loading effects between logic stages independently. That extent is defined by the operating frequency: as frequencies increase, the input impedance of the MOSFETs decreases.

Analog[edit]

The MOSFET's advantages in digital circuits do not translate into supremacy in all analog circuits. The two types of circuit draw upon different features of transistor behavior. Digital circuits switch, spending most of their time either fully on or fully off. The transition from one to the other is only of concern with regards to speed and charge required. Analog circuits depend on operation in the transition region where small changes to Vgs can modulate the output (drain) current. The JFET and bipolar junction transistor (BJT) are preferred for accurate matching (of adjacent devices in integrated circuits), higher transconductance and certain temperature characteristics which simplify keeping performance predictable as circuit temperature varies.

Nevertheless, MOSFETs are widely used in many types of analog circuits because of their own advantages (zero gate current, high and adjustable output impedance and improved robustness vs. BJTs which can be permanently degraded by even lightly breaking down the emitter-base).[vague] The characteristics and performance of many analog circuits can be scaled up or down by changing the sizes (length and width) of the MOSFETs used. By comparison, in bipolar transistors the size of the device does not significantly affect its performance.[citation needed] MOSFETs' ideal characteristics regarding gate current (zero) and drain-source offset voltage (zero) also make them nearly ideal switch elements, and also make switched capacitor analog circuits practical. In their linear region, MOSFETs can be used as precision resistors, which can have a much higher controlled resistance than BJTs. In high power circuits, MOSFETs sometimes have the advantage of not suffering from thermal runaway as BJTs do.[dubious ] Also, MOSFETs can be configured to perform as capacitors and gyrator circuits which allow op-amps made from them to appear as inductors, thereby allowing all of the normal analog devices on a chip (except for diodes, which can be made smaller than a MOSFET anyway) to be built entirely out of MOSFETs. This means that complete analog circuits can be made on a silicon chip in a much smaller space and with simpler fabrication techniques. MOSFETS are ideally suited to switch inductive loads because of tolerance to inductive kickback.

Some ICs combine analog and digital MOSFET circuitry on a single mixed-signal integrated circuit, making the needed board space even smaller. This creates a need to isolate the analog circuits from the digital circuits on a chip level, leading to the use of isolation rings and silicon on insulator (SOI). Since MOSFETs require more space to handle a given amount of power than a BJT, fabrication processes can incorporate BJTs and MOSFETs into a single device. Mixed-transistor devices are called bi-FETs (bipolar FETs) if they contain just one BJT-FET and BiCMOS (bipolar-CMOS) if they contain complementary BJT-FETs. Such devices have the advantages of both insulated gates and higher current density.

In the late 1980s, Asad Abidi pioneered RF CMOS technology, which uses MOS VLSI circuits, while working at UCLA. This changed the way in which RF circuits were designed, away from discrete bipolar transistors and towards CMOS integrated circuits. As of 2008, the radio transceivers in all wireless networking devices and modern mobile phones are mass-produced as RF CMOS devices.[144]

Analog switches[edit]

MOSFET analog switches use the MOSFET to pass analog signals when on, and as a high impedance when off. Signals flow in both directions across a MOSFET switch. In this application, the drain and source of a MOSFET exchange places depending on the relative voltages of the source/drain electrodes. The source is the more negative side for an N-MOS or the more positive side for a P-MOS. All of these switches are limited on what signals they can pass or stop by their gate–source, gate–drain, and source–drain voltages; exceeding the voltage, current, or power limits will potentially damage the switch.

Single-type[edit]

This analog switch uses a four-terminal simple MOSFET of either P or N type.

In the case of an n-type switch, the body is connected to the most negative supply (usually GND) and the gate is used as the switch control. Whenever the gate voltage exceeds the source voltage by at least a threshold voltage, the MOSFET conducts. The higher the voltage, the more the MOSFET can conduct. An N-MOS switch passes all voltages less than VgateVtn. When the switch is conducting, it typically operates in the linear (or ohmic) mode of operation, since the source and drain voltages will typically be nearly equal.

In the case of a P-MOS, the body is connected to the most positive voltage, and the gate is brought to a lower potential to turn the switch on. The P-MOS switch passes all voltages higher than VgateVtp (threshold voltage Vtp is negative in the case of enhancement-mode P-MOS).

Dual-type (CMOS)[edit]

This "complementary" or CMOS type of switch uses one P-MOS and one N-MOS FET to counteract the limitations of the single-type switch. The FETs have their drains and sources connected in parallel, the body of the P-MOS is connected to the high potential (VDD) and the body of the N-MOS is connected to the low potential (gnd). To turn the switch on, the gate of the P-MOS is driven to the low potential and the gate of the N-MOS is driven to the high potential. For voltages between VDDVtn and gndVtp, both FETs conduct the signal; for voltages less than gndVtp, the N-MOS conducts alone; and for voltages greater than VDDVtn, the P-MOS conducts alone.

The voltage limits for this switch are the gate–source, gate–drain and source–drain voltage limits for both FETs. Also, the P-MOS is typically two to three times wider than the N-MOS, so the switch will be balanced for speed in the two directions.

Tri-state circuitry sometimes incorporates a CMOS MOSFET switch on its output to provide for a low-ohmic, full-range output when on, and a high-ohmic, mid-level signal when off.

Power electronics[edit]

Power MOSFETs[edit]

The power MOSFET is the most widely used power device in the world.[231] Advantages over bipolar junction transistors in power electronics include MOSFETs not requiring a continuous flow of drive current to remain in the ON state, offering higher switching speeds, lower switching power losses, lower on-resistances, and reduced susceptibility to thermal runaway.[160] The power MOSFET had an impact on power supplies, enabling higher operating frequencies, size and weight reduction, and increased volume production.[261]

Switching power supplies are the most common applications for power MOSFETs, which are also widely used for [83] MOSFET-based RF power amplifiers enabled the transition of mobile networks from analog to digital in the 1990s, leading to the wide proliferation of wireless mobile networks, which revolutionised telecommunication systems.[71] The LDMOS in particular is the most widely used power amplifier in mobile networks, such as 2G, 3G,[71] and 4G.[72] Over 50 billion discrete power MOSFETs are shipped annually, as of 2018. They are widely used for automotive, industrial and communications systems in particular.[262] Power MOSFETs are commonly used in automotive electronics, particularly as switching devices in electronic control units,[92] and as power converters in modern electric vehicles.[97] The insulated-gate bipolar transistor (IGBT), a hybrid MOS-bipolar transistor, is also used for a wide variety of applications.[96]

Space industry[edit]

In the space industry, MOSFET devices were adopted by NASA for space research in 1964, for its Interplanetary Monitoring Platform (IMP) program[171] and Explorers space exploration program.[32] The use of MOSFETs was a major step forward in the electronics design of spacecraft and satellites.[170] The IMP D (Explorer 33), launched in 1966, was the first spacecraft to use the MOSFET.[32] Data gathered by IMP spacecraft and satellites were used to support the Apollo program, enabling the first manned Moon landing with the Apollo 11 mission in 1969.[170]

The Cassini–Huygens mission to Saturn in 1997 had power distribution accomplished 192 solid-state power switches (SSPS), which also functioned as circuit breakers in the event of an overload condition. The switches were developed from a combination of two semiconductor devices with switching capabilities: the MOSFET and the ASIC (application-specific integrated circuit). This combination resulted in advanced power switches that had better performance characteristics than traditional mechanical switches.[158]

MOS memory[edit]

The first modern memory cells for computer memory was introduced in 1965, when John Schmidt at Fairchild Semiconductor designed the first MOS semiconductor memory, a 64-bit MOS SRAM (static random-access memory).[149] SRAM became an alternative to magnetic-core memory, but required six MOS transistors for each bit of data.[263]

MOS technology is the basis for DRAM (dynamic random-access memory). In 1966, Dr. Robert H. Dennard at the IBM Thomas J. Watson Research Center was working on MOS memory. While examining the characteristics of MOS technology, he found it was capable of building capacitors, and that storing a charge or no charge on the MOS capacitor could represent the 1 and 0 of a bit, while the MOS transistor could control writing the charge to the capacitor. This led to his development of a single-transistor DRAM memory cell.[263] In 1967, Dennard filed a patent under IBM for a single-transistor DRAM (dynamic random-access memory) memory cell, based on MOS technology.[166] MOS memory enabled higher performance, was cheaper, and consumed less power, than magnetic-core memory, leading to MOS memory overtaking magnetic core memory as the dominant computer memory technology by the early 1970s.[264]

Frank Wanlass, while studying MOSFET structures in 1963, noted the movement of charge through oxide onto a gate. While he did not pursue it, this idea would later become the basis for EPROM (erasable programmable read-only memory) technology.[265] In 1967, Dawon Kahng and Simon Sze proposed that floating-gate memory cells, consisting of floating-gate MOSFETs (FGMOS), could be used to produce reprogrammable ROM (read-only memory).[130] Floating-gate memory cells later became the basis for non-volatile memory (NVM) technologies including EPROM, EEPROM (electrically erasable programmable ROM) and flash memory.[131]

Sensors[edit]

MOSFET sensors are widely used to measure physical, chemical, biological and environmental parameters.[129] The ion-sensitive field-effect transistor (ISFET), for example, is widely used in biomedical applications, such as the detection of DNA hybridization, biomarker detection from blood, antibody detection, glucose measurement, pH sensing, and genetic technology.[98]

MOSFETs are also widely used in microelectromechanical systems (MEMS), as silicon MOSFETs could interact and communicate with the surroundings and process things such as chemicals, motions and light.[141] An early example of a MEMS device is the resonant-gate transistor, an adaptation of the MOSFET, developed by Harvey C. Nathanson in 1965.[266]

Image sensors[edit]

MOS technology is the basis for modern image sensors, including the charge-coupled device (CCD) and the CMOS active-pixel sensor (CMOS sensor), used in digital imaging and digital cameras.[75] Willard Boyle and George E. Smith developed the CCD in 1969. While researching the MOS process, they realized that an electric charge was the analogy of the magnetic bubble and that it could be stored on a tiny MOS capacitor. As it was fairly straighforward to fabricate a series of MOS capacitors in a row, they connected a suitable voltage to them so that the charge could be stepped along from one to the next.[75] The CCD is a semiconductor circuit that was later used in the first digital video cameras for television broadcasting.[267]

The MOS active-pixel sensor (APS) was developed by Tsutomu Nakamura at Olympus in 1985.[268] The CMOS active-pixel sensor was later developed by Eric Fossum and his team in the early 1990s.[269]

MOS image sensors are widely used in optical mouse technology. The first optical mouse, invented by Richard F. Lyon at Xerox in 1980, used a 5 µm NMOS sensor chip.[122][123] Since the first commercial optical mouse, the IntelliMouse introduced in 1999, most optical mouse devices use CMOS sensors.[270]

Quantum physics[edit]

The MOSFET enables physicists to study electron behavior in a two-dimensional gas, called the two-dimensional electron gas (2DEG). In a MOSFET, conduction electrons travel in a thin surface layer, and a "gate" voltage controls the number of charge carriers in this layer. This allows researchers to explore quantum effects by operating high-purity MOSFETs at liquid helium temperatures.[74]

In 1978, the Gakushuin University researchers Jun-ichi Wakabayashi and Shinji Kawaji observed the Hall effect in experiments carried out on the inversion layer of MOSFETs.[271] In 1980, Klaus von Klitzing, working at the high magnetic field laboratory in Grenoble with silicon-based MOSFET samples developed by Michael Pepper and Gerhard Dorda, made the unexpected discovery of the quantum Hall effect.[74][161]

Construction[edit]

Gate material[edit]

The primary criterion for the gate material is that it is a good conductor. Highly doped polycrystalline silicon is an acceptable but certainly not ideal conductor, and also suffers from some more technical deficiencies in its role as the standard gate material. Nevertheless, there are several reasons favoring use of polysilicon:

  1. The threshold voltage (and consequently the drain to source on-current) is modified by the work function difference between the gate material and channel material. Because polysilicon is a semiconductor, its work function can be modulated by adjusting the type and level of doping. Furthermore, because polysilicon has the same bandgap as the underlying silicon channel, it is quite straightforward to tune the work function to achieve low threshold voltages for both NMOS and PMOS devices. By contrast, the work functions of metals are not easily modulated, so tuning the work function to obtain low threshold voltages (LVT) becomes a significant challenge. Additionally, obtaining low-threshold devices on both PMOS and NMOS devices sometimes requires the use of different metals for each device type. While bimetallic integrated circuits (i.e., one type of metal for gate electrodes of NFETS and a second type of metal for gate electrodes of PFETS) are not common, they are known in patent literature and provide some benefit in terms of tuning electrical circuits' overall electrical performance.
  2. The silicon-SiO2 interface has been well studied and is known to have relatively few defects. By contrast many metal-insulator interfaces contain significant levels of defects which can lead to Fermi level pinning, charging, or other phenomena that ultimately degrade device performance.
  3. In the MOSFET IC fabrication process, it is preferable to deposit the gate material prior to certain high-temperature steps in order to make better-performing transistors. Such high temperature steps would melt some metals, limiting the types of metal that can be used in a metal-gate-based process.

While polysilicon gates have been the de facto standard for the last twenty years, they do have some disadvantages which have led to their likely future replacement by metal gates. These disadvantages include:

  • Polysilicon is not a great conductor (approximately 1000 times more resistive than metals) which reduces the signal propagation speed through the material. The resistivity can be lowered by increasing the level of doping, but even highly doped polysilicon is not as conductive as most metals. To improve conductivity further, sometimes a high-temperature metal such as tungsten, titanium, cobalt, and more recently nickel is alloyed with the top layers of the polysilicon. Such a blended material is called silicide. The silicide-polysilicon combination has better electrical properties than polysilicon alone and still does not melt in subsequent processing. Also the threshold voltage is not significantly higher than with polysilicon alone, because the silicide material is not near the channel. The process in which silicide is formed on both the gate electrode and the source and drain regions is sometimes called salicide, self-aligned silicide.
  • When the transistors are extremely scaled down, it is necessary to make the gate dielectric layer very thin, around 1 nm in state-of-the-art technologies. A phenomenon observed here is the so-called poly depletion, where a depletion layer is formed in the gate polysilicon layer next to the gate dielectric when the transistor is in the inversion. To avoid this problem, a metal gate is desired. A variety of metal gates such as tantalum, tungsten, tantalum nitride, and titanium nitride are used, usually in conjunction with high-κ dielectrics. An alternative is to use fully silicided polysilicon gates, a process known as FUSI.

Present high performance CPUs use metal gate technology, together with high-κ dielectrics, a combination known as high-κ, metal gate (HKMG). The disadvantages of metal gates are overcome by a few techniques:[272]

  1. The threshold voltage is tuned by including a thin "work function metal" layer between the high-κ dielectric and the main metal. This layer is thin enough that the total work function of the gate is influenced by both the main metal and thin metal work functions (either due to alloying during annealing, or simply due to the incomplete screening by the thin metal). The threshold voltage thus can be tuned by the thickness of the thin metal layer.
  2. High-κ dielectrics are now well studied, and their defects are understood.
  3. HKMG processes exist that do not require the metals to experience high temperature anneals; other processes select metals that can survive the annealing step.

Insulator[edit]

As devices are made smaller, insulating layers are made thinner, often through steps of thermal oxidation or localised oxidation of silicon (LOCOS). For nano-scaled devices, at some point tunneling of carriers through the insulator from the channel to the gate electrode takes place. To reduce the resulting leakage current, the insulator can be made thinner by choosing a material with a higher dielectric constant. To see how thickness and dielectric constant are related, note that Gauss's law connects field to charge as:

with Q = charge density, κ = dielectric constant, ε0 = permittivity of empty space and E = electric field. From this law it appears the same charge can be maintained in the channel at a lower field provided κ is increased. The voltage on the gate is given by:

with VG = gate voltage, Vch = voltage at channel side of insulator, and tins = insulator thickness. This equation shows the gate voltage will not increase when the insulator thickness increases, provided κ increases to keep tins / κ = constant (see the article on high-κ dielectrics for more detail, and the section in this article on gate-oxide leakage).

The insulator in a MOSFET is a dielectric which can in any event be silicon oxide, formed by LOCOS but many other dielectric materials are employed. The generic term for the dielectric is gate dielectric since the dielectric lies directly below the gate electrode and above the channel of the MOSFET.

Junction design[edit]

MOSFET showing shallow junction extensions, raised source and drain and halo implant. Raised source and drain separated from gate by oxide spacers

The source-to-body and drain-to-body junctions are the object of much attention because of three major factors: their design affects the current-voltage (I-V) characteristics of the device, lowering output resistance, and also the speed of the device through the loading effect of the junction capacitances, and finally, the component of stand-by power dissipation due to junction leakage.

The drain induced barrier lowering of the threshold voltage and channel length modulation effects upon I-V curves are reduced by using shallow junction extensions. In addition, halo doping can be used, that is, the addition of very thin heavily doped regions of the same doping type as the body tight against the junction walls to limit the extent of depletion regions.[273]

The capacitive effects are limited by using raised source and drain geometries that make most of the contact area border thick dielectric instead of silicon.[274]

These various features of junction design are shown (with artistic license) in the figure.

Scaling[edit]

Trend of Intel CPU transistor gate length
MOSFET version of gain-boosted current mirror; M1 and M2 are in active mode, while M3 and M4 are in Ohmic mode, and act like resistors. The operational amplifier provides feedback that maintains a high output resistance.

Over the past decades, the MOSFET (as used for digital logic) has continually been scaled down in size; typical MOSFET channel lengths were once several micrometres, but modern integrated circuits are incorporating MOSFETs with channel lengths of tens of nanometers. Robert Dennard's work on scaling theory was pivotal in recognising that this ongoing reduction was possible. The semiconductor industry maintains a "roadmap", the ITRS,[275] which sets the pace for MOSFET development. Historically, the difficulties with decreasing the size of the MOSFET have been associated with the semiconductor device fabrication process, the need to use very low voltages, and with poorer electrical performance necessitating circuit redesign and innovation (small MOSFETs exhibit higher leakage currents and lower output resistance). As of 2019, the smallest MOSFETs in production are 5 nm FinFET semiconductor nodes, manufactured by Samsung Electronics and TSMC.[276][277]

Smaller MOSFETs are desirable for several reasons. The main reason to make transistors smaller is to pack more and more devices in a given chip area. This results in a chip with the same functionality in a smaller area, or chips with more functionality in the same area. Since fabrication costs for a semiconductor wafer are relatively fixed, the cost per integrated circuits is mainly related to the number of chips that can be produced per wafer. Hence, smaller ICs allow more chips per wafer, reducing the price per chip. In fact, over the past 30 years the number of transistors per chip has been doubled every 2–3 years once a new technology node is introduced. For example, the number of MOSFETs in a microprocessor fabricated in a 45 nm technology can well be twice as many as in a 65 nm chip. This doubling of transistor density was first observed by Gordon Moore in 1965 and is commonly referred to as Moore's law.[278] It is also expected that smaller transistors switch faster. For example, one approach to size reduction is a scaling of the MOSFET that requires all device dimensions to reduce proportionally. The main device dimensions are the channel length, channel width, and oxide thickness. When they are scaled down by equal factors, the transistor channel resistance does not change, while gate capacitance is cut by that factor. Hence, the RC delay of the transistor scales with a similar factor. While this has been traditionally the case for the older technologies, for the state-of-the-art MOSFETs reduction of the transistor dimensions does not necessarily translate to higher chip speed because the delay due to interconnections is more significant.

Producing MOSFETs with channel lengths much smaller than a micrometre is a challenge, and the difficulties of semiconductor device fabrication are always a limiting factor in advancing integrated circuit technology. Though processes such as ALD have improved fabrication for small components, the small size of the MOSFET (less than a few tens of nanometers) has created operational problems:

Higher subthreshold conduction
As MOSFET geometries shrink, the voltage that can be applied to the gate must be reduced to maintain reliability. To maintain performance, the threshold voltage of the MOSFET has to be reduced as well. As threshold voltage is reduced, the transistor cannot be switched from complete turn-off to complete turn-on with the limited voltage swing available; the circuit design is a compromise between strong current in the on case and low current in the off case, and the application determines whether to favor one over the other. Subthreshold leakage (including subthreshold conduction, gate-oxide leakage and reverse-biased junction leakage), which was ignored in the past, now can consume upwards of half of the total power consumption of modern high-performance VLSI chips.[279][280]
Increased gate-oxide leakage
The gate oxide, which serves as insulator between the gate and channel, should be made as thin as possible to increase the channel conductivity and performance when the transistor is on and to reduce subthreshold leakage when the transistor is off. However, with current gate oxides with a thickness of around 1.2 nm (which in silicon is ~5 atoms thick) the quantum mechanical phenomenon of electron tunneling occurs between the gate and channel, leading to increased power consumption. Silicon dioxide has traditionally been used as the gate insulator. Silicon dioxide however has a modest dielectric constant. Increasing the dielectric constant of the gate dielectric allows a thicker layer while maintaining a high capacitance (capacitance is proportional to dielectric constant and inversely proportional to dielectric thickness). All else equal, a higher dielectric thickness reduces the quantum tunneling current through the dielectric between the gate and the channel. Insulators that have a larger dielectric constant than silicon dioxide (referred to as high-κ dielectrics), such as group IVb metal silicates e.g. hafnium and zirconium silicates and oxides are being used to reduce the gate leakage from the 45 nanometer technology node onwards. On the other hand, the barrier height of the new gate insulator is an important consideration; the difference in conduction band energy between the semiconductor and the dielectric (and the corresponding difference in valence band energy) also affects leakage current level. For the traditional gate oxide, silicon dioxide, the former barrier is approximately 8 eV. For many alternative dielectrics the value is significantly lower, tending to increase the tunneling current, somewhat negating the advantage of higher dielectric constant. The maximum gate–source voltage is determined by the strength of the electric field able to be sustained by the gate dielectric before significant leakage occurs. As the insulating dielectric is made thinner, the electric field strength within it goes up for a fixed voltage. This necessitates using lower voltages with the thinner dielectric.
Increased junction leakage
To make devices smaller, junction design has become more complex, leading to higher doping levels, shallower junctions, "halo" doping and so forth,[281][282] all to decrease drain-induced barrier lowering (see the section on junction design). To keep these complex junctions in place, the annealing steps formerly used to remove damage and electrically active defects must be curtailed[283] increasing junction leakage. Heavier doping is also associated with thinner depletion layers and more recombination centers that result in increased leakage current, even without lattice damage.
Drain-induced barrier lowering (DIBL) and VT roll off
Because of the short-channel effect, channel formation is not entirely done by the gate, but now the drain and source also affect the channel formation. As the channel length decreases, the depletion regions of the source and drain come closer together and make the threshold voltage (VT) a function of the length of the channel. This is called VT roll-off. VT also becomes function of drain to source voltage VDS. As we increase the VDS, the depletion regions increase in size, and a considerable amount of charge is depleted by the VDS. The gate voltage required to form the channel is then lowered, and thus, the VT decreases with an increase in VDS. This effect is called drain induced barrier lowering (DIBL).
Lower output resistance
For analog operation, good gain requires a high MOSFET output impedance, which is to say, the MOSFET current should vary only slightly with the applied drain-to-source voltage. As devices are made smaller, the influence of the drain competes more successfully with that of the gate due to the growing proximity of these two electrodes, increasing the sensitivity of the MOSFET current to the drain voltage. To counteract the resulting decrease in output resistance, circuits are made more complex, either by requiring more devices, for example the cascode and cascade amplifiers, or by feedback circuitry using operational amplifiers, for example a circuit like that in the adjacent figure.
Lower transconductance
The transconductance of the MOSFET decides its gain and is proportional to hole or electron mobility (depending on device type), at least for low drain voltages. As MOSFET size is reduced, the fields in the channel increase and the dopant impurity levels increase. Both changes reduce the carrier mobility, and hence the transconductance. As channel lengths are reduced without proportional reduction in drain voltage, raising the electric field in the channel, the result is velocity saturation of the carriers, limiting the current and the transconductance.
Interconnect capacitance
Traditionally, switching time was roughly proportional to the gate capacitance of gates. However, with transistors becoming smaller and more transistors being placed on the chip, interconnect capacitance (the capacitance of the metal-layer connections between different parts of the chip) is becoming a large percentage of capacitance.[284][285] Signals have to travel through the interconnect, which leads to increased delay and lower performance.
Heat production
The ever-increasing density of MOSFETs on an integrated circuit creates problems of substantial localized heat generation that can impair circuit operation. Circuits operate more slowly at high temperatures, and have reduced reliability and shorter lifetimes. Heat sinks and other cooling devices and methods are now required for many integrated circuits including microprocessors. Power MOSFETs are at risk of thermal runaway. As their on-state resistance rises with temperature, if the load is approximately a constant-current load then the power loss rises correspondingly, generating further heat. When the heatsink is not able to keep the temperature low enough, the junction temperature may rise quickly and uncontrollably, resulting in destruction of the device.
Process variations
With MOSFETs becoming smaller, the number of atoms in the silicon that produce many of the transistor's properties is becoming fewer, with the result that control of dopant numbers and placement is more erratic. During chip manufacturing, random process variations affect all transistor dimensions: length, width, junction depths, oxide thickness etc., and become a greater percentage of overall transistor size as the transistor shrinks. The transistor characteristics become less certain, more statistical. The random nature of manufacture means we do not know which particular example MOSFETs actually will end up in a particular instance of the circuit. This uncertainty forces a less optimal design because the design must work for a great variety of possible component MOSFETs. See process variation, design for manufacturability, reliability engineering, and statistical process control.[286]
Modeling challenges
Modern ICs are computer-simulated with the goal of obtaining working circuits from the very first manufactured lot. As devices are miniaturized, the complexity of the processing makes it difficult to predict exactly what the final devices look like, and modeling of physical processes becomes more challenging as well. In addition, microscopic variations in structure due simply to the probabilistic nature of atomic processes require statistical (not just deterministic) predictions. These factors combine to make adequate simulation and "right the first time" manufacture difficult.

A related scaling rule is Edholm's law. In 2004, Phil Edholm observed that the bandwidth of telecommunication networks (including the Internet) is doubling every 18 months.[287] Over the course of several decades, the bandwidths of communication networks has risen from bits per second to terabits per second. The rapid rise in telecommunication bandwidth is largely due to the same MOSFET scaling that enables Moore's law, as telecommunication networks are built from MOSFETs.[73]

Timeline[edit]

PMOS and NMOS[edit]

MOSFET (PMOS and NMOS) demonstrations
Date Channel length Oxide thickness[288] MOSFET logic Researcher(s) Organization Ref
June 1960 20,000 nm 100 nm PMOS Mohamed M. Atalla, Dawon Kahng Bell Telephone Laboratories [289][290]
NMOS
10,000 nm 100 nm PMOS Mohamed M. Atalla, Dawon Kahng Bell Telephone Laboratories [291]
NMOS
May 1965 8,000 nm 150 nm NMOS Chih-Tang Sah, Otto Leistiko, A.S. Grove Fairchild Semiconductor [292]
5,000 nm 170 nm PMOS
December 1972 1,000 nm ? PMOS Robert H. Dennard, Fritz H. Gaensslen, Hwa-Nien Yu IBM T.J. Watson Research Center [293][294][295]
1973 7,500 nm ? NMOS Sohichi Suzuki NEC [296][297]
6,000 nm ? PMOS ? Toshiba [298][299]
October 1974 1,000 nm 35 nm NMOS Robert H. Dennard, Fritz H. Gaensslen, Hwa-Nien Yu IBM T.J. Watson Research Center [300]
500 nm
September 1975 1,500 nm 20 nm NMOS Ryoichi Hori, Hiroo Masuda, Osamu Minato Hitachi [294][301]
March 1976 3,000 nm ? NMOS ? Intel [302]
April 1979 1,000 nm 25 nm NMOS William R. Hunter, L. M. Ephrath, Alice Cramer IBM T.J. Watson Research Center [303]
December 1984 100 nm 5 nm NMOS Toshio Kobayashi, Seiji Horiguchi, K. Kiuchi Nippon Telegraph and Telephone [304]
December 1985 150 nm 2.5 nm NMOS Toshio Kobayashi, Seiji Horiguchi, M. Miyake, M. Oda Nippon Telegraph and Telephone [305]
75 nm ? NMOS Stephen Y. Chou, Henry I. Smith, Dimitri A. Antoniadis MIT [306]
January 1986 60 nm ? NMOS Stephen Y. Chou, Henry I. Smith, Dimitri A. Antoniadis MIT [307]
June 1987 200 nm 3.5 nm PMOS Toshio Kobayashi, M. Miyake, K. Deguchi Nippon Telegraph and Telephone [308]
December 1993 40 nm ? NMOS Mizuki Ono, Masanobu Saito, Takashi Yoshitomi Toshiba [309]
September 1996 16 nm ? PMOS Hisao Kawaura, Toshitsugu Sakamoto, Toshio Baba NEC [310]
June 1998 50 nm 1.3 nm NMOS Khaled Z. Ahmed, Effiong E. Ibok, Miryeong Song Advanced Micro Devices (AMD) [311][312]
December 2002 6 nm ? PMOS Bruce Doris, Omer Dokumaci, Meikei Ieong IBM [313][314][315]
December 2003 3 nm ? PMOS Hitoshi Wakabayashi, Shigeharu Yamagami NEC [316][314]
NMOS

CMOS (single-gate)[edit]

Complementary MOSFET (CMOS) demonstrations (single-gate)
Date Channel length Oxide thickness[288] Researcher(s) Organization Ref
February 1963 ? ? Chih-Tang Sah, Frank Wanlass Fairchild Semiconductor [220][317]
1968 20,000 nm 100 nm ? RCA Laboratories [318]
1970 10,000 nm 100 nm ? RCA Laboratories [318]
December 1976 2,000 nm ? A. Aitken, R.G. Poulsen, A.T.P. MacArthur, J.J. White Mitel Semiconductor [319]
February 1978 3,000 nm ? Toshiaki Masuhara, Osamu Minato, Toshio Sasaki, Yoshio Sakai Hitachi Central Research Laboratory [8][320][321]
February 1983 1,200 nm 25 nm R.J.C. Chwang, M. Choi, D. Creek, S. Stern, P.H. Pelley Intel [322][323]
900 nm 15 nm Tsuneo Mano, J. Yamada, Junichi Inoue, S. Nakajima Nippon Telegraph and Telephone (NTT) [322][324]
December 1983 1,000 nm 22.5 nm G.J. Hu, Yuan Taur, Robert H. Dennard, Chung-Yu Ting IBM T.J. Watson Research Center [325]
February 1987 800 nm 17 nm T. Sumi, Tsuneo Taniguchi, Mikio Kishimoto, Hiroshige Hirano Matsushita [322][326]
700 nm 12 nm Tsuneo Mano, J. Yamada, Junichi Inoue, S. Nakajima Nippon Telegraph and Telephone (NTT) [322][327]
September 1987 500 nm 12.5 nm Hussein I. Hanafi, Robert H. Dennard, Yuan Taur, Nadim F. Haddad IBM T.J. Watson Research Center [328]
December 1987 250 nm ? Naoki Kasai, Nobuhiro Endo, Hiroshi Kitajima NEC [329]
February 1988 400 nm 10 nm M. Inoue, H. Kotani, T. Yamada, Hiroyuki Yamauchi Matsushita [322][330]
December 1990 100 nm ? Ghavam G. Shahidi, Bijan Davari, Yuan Taur, James D. Warnock IBM T.J. Watson Research Center [331]
1993 350 nm ? ? Sony [332]
1996 150 nm ? ? Mitsubishi Electric
1998 180 nm ? ? TSMC [333]
December 2003 5 nm ? Hitoshi Wakabayashi, Shigeharu Yamagami, Nobuyuki Ikezawa NEC [316][334]

Multi-gate MOSFET (MuGFET)[edit]

Multi-gate MOSFET (MuGFET) demonstrations
Date Channel length MuGFET type Researcher(s) Organization Ref
August 1984 ? DGMOS Toshihiro Sekigawa, Yutaka Hayashi Electrotechnical Laboratory (ETL) [335]
1987 2,000 nm DGMOS Toshihiro Sekigawa Electrotechnical Laboratory (ETL) [336]
December 1988 250 nm DGMOS Bijan Davari, Wen-Hsing Chang, Matthew R. Wordeman, C.S. Oh IBM T.J. Watson Research Center [337][338]
180 nm
? GAAFET Fujio Masuoka, Hiroshi Takato, Kazumasa Sunouchi, N. Okabe Toshiba [339][340][341]
December 1989 200 nm FinFET Digh Hisamoto, Toru Kaga, Yoshifumi Kawamoto, Eiji Takeda Hitachi Central Research Laboratory [342][343][344]
December 1998 17 nm FinFET Digh Hisamoto, Chenming Hu, Tsu-Jae King Liu, Jeffrey Bokor University of California (Berkeley) [153][345]
2001 15 nm FinFET Chenming Hu, Yang‐Kyu Choi, Nick Lindert, Tsu-Jae King Liu University of California (Berkeley) [153][346]
December 2002 10 nm FinFET Shibly Ahmed, Scott Bell, Cyrus Tabery, Jeffrey Bokor University of California (Berkeley) [153][347]
June 2006 3 nm GAAFET Hyunjin Lee, Yang-kyu Choi, Lee-Eun Yu, Seong-Wan Ryu KAIST [348][349]

Other types of MOSFET[edit]

MOSFET demonstrations (other types)
Date Channel length Oxide thickness[288] MOSFET type Researcher(s) Organization Ref
October 1962 ? ? TFT Paul K. Weimer RCA Laboratories [350][137]
October 1966 100,000 nm 100 nm TFT T.P. Brody, H.E. Kunig Westinghouse Electric [351][352]
August 1967 ? ? FGMOS Dawon Kahng, Simon Min Sze Bell Telephone Laboratories [353]
October 1967 ? ? MNOS H.A. Richard Wegener, A.J. Lincoln, H.C. Pao Sperry Corporation [354]
July 1968 ? ? BiMOS Hung-Chang Lin, Ramachandra R. Iyer Westinghouse Electric [355][356]
October 1968 ? ? BiCMOS Hung-Chang Lin, Ramachandra R. Iyer, C.T. Ho Westinghouse Electric [357][356]
1969 ? ? VMOS ? Hitachi [358][359]
September 1969 ? ? DMOS Y. Tarui, Y. Hayashi, Toshihiro Sekigawa Electrotechnical Laboratory (ETL) [360][361]
October 1970 ? ? ISFET Piet Bergveld University of Twente [362][363]
October 1970 1,000 nm ? DMOS Y. Tarui, Y. Hayashi, Toshihiro Sekigawa Electrotechnical Laboratory (ETL) [364]
1977 ? ? VDMOS John Louis Moll HP Labs [358]
? ? LDMOS ? Hitachi [90]
July 1979 ? ? IGBT Bantval Jayant Baliga, Margaret Lazeri General Electric [365]
December 1984 2,000 nm ? BiCMOS H. Higuchi, Goro Kitsukawa, Takahide Ikeda, Y. Nishio Hitachi [366]
May 1985 300 nm ? ? K. Deguchi, Kazuhiko Komatsu, M. Miyake, H. Namatsu Nippon Telegraph and Telephone [367]
February 1985 1,000 nm ? BiCMOS H. Momose, Hideki Shibata, S. Saitoh, Jun-ichi Miyamoto Toshiba [368]
November 1986 90 nm 8.3 nm ? Han-Sheng Lee, L.C. Puzio General Motors [369]
December 1986 60 nm ? ? Ghavam G. Shahidi, Dimitri A. Antoniadis, Henry I. Smith MIT [370][307]
May 1987 ? 10 nm ? Bijan Davari, Chung-Yu Ting, Kie Y. Ahn, S. Basavaiah IBM T.J. Watson Research Center [371]
December 1987 800 nm ? BiCMOS Robert H. Havemann, R. E. Eklund, Hiep V. Tran Texas Instruments [372]
June 1997 30 nm ? EJ-MOSFET Hisao Kawaura, Toshitsugu Sakamoto, Toshio Baba NEC [373]
1998 32 nm ? ? ? NEC [314]
1999 8 nm
April 2000 8 nm ? EJ-MOSFET Hisao Kawaura, Toshitsugu Sakamoto, Toshio Baba NEC [374]

See also[edit]

References[edit]

  1. ^ a b c "Who Invented the Transistor?". Computer History Museum. 4 December 2013. Retrieved 20 July 2019.
  2. ^ Bakshi, U. A.; Godse, A. P. (2007). "§8.2 The depletion mode MOSFET". Electronic Circuits. Technical Publications. pp. 8–2. ISBN 978-81-8431-284-3.
  3. ^ a b Motoyoshi, M. (2009). "Through-Silicon Via (TSV)" (PDF). Proceedings of the IEEE. 97 (1): 43–48. doi:10.1109/JPROC.2008.2007462. ISSN 0018-9219.
  4. ^ Lécuyer, Christophe (2006). Making Silicon Valley: Innovation and the Growth of High Tech, 1930-1970. Chemical Heritage Foundation. p. 273. ISBN 9780262122818.
  5. ^ a b c d Sze, Simon Min. "Metal–oxide–semiconductor field-effect transistors". Encyclopedia Britannica. Retrieved 21 July 2019.
  6. ^ a b "Transistors Keep Moore's Law Alive". EETimes. 12 December 2018. Retrieved 18 July 2019.
  7. ^ a b c d e "Tortoise of Transistors Wins the Race - CHM Revolution". Computer History Museum. Retrieved 22 July 2019.
  8. ^ a b c d e "1978: Double-well fast CMOS SRAM (Hitachi)" (PDF). Semiconductor History Museum of Japan. Retrieved 5 July 2019.
  9. ^ Higgins, Richard J. (1983). Electronics with digital and analog integrated circuits. Prentice-Hall. p. 101. ISBN 9780132507042. The dominant difference is power: CMOS gates can consume about 100,000 times less power than their TTL equivalents!
  10. ^ Lilienfeld, Julius Edgar (1926-10-08) "Method and apparatus for controlling electric currents" U.S. Patent 1,745,175A
  11. ^ a b c d e f "Dawon Kahng". National Inventors Hall of Fame. Retrieved 27 June 2019.
  12. ^ a b c d e f "1960: Metal Oxide Semiconductor (MOS) Transistor Demonstrated". The Silicon Engine: A Timeline of Semiconductors in Computers. Computer History Museum. Retrieved August 31, 2019.
  13. ^ Lee, Thomas H. (2003). The Design of CMOS Radio-Frequency Integrated Circuits (PDF). Cambridge University Press. ISBN 9781139643771.
  14. ^ a b c Puers, Robert; Baldi, Livio; Voorde, Marcel Van de; Nooten, Sebastiaan E. van (2017). Nanoelectronics: Materials, Devices, Applications, 2 Volumes. John Wiley & Sons. p. 14. ISBN 9783527340538.
  15. ^ a b Deal, Bruce E. (1998). "Highlights Of Silicon Thermal Oxidation Technology". Silicon materials science and technology. The Electrochemical Society. p. 183. ISBN 9781566771931.
  16. ^ a b c d Moskowitz, Sanford L. (2016). Advanced Materials Innovation: Managing Global Technology in the 21st century. John Wiley & Sons. pp. 165–167. ISBN 9780470508923.
  17. ^ a b c d e "The Foundation of Today's Digital World: The Triumph of the MOS Transistor". Computer History Museum. 13 July 2010. Retrieved 21 July 2019.
  18. ^ a b c d e "Martin (John) M. Atalla". National Inventors Hall of Fame. 2009. Retrieved 21 June 2013.
  19. ^ a b c d Lojek, Bo (2007). History of Semiconductor Engineering. Springer Science & Business Media. pp. 321–3. ISBN 9783540342588.
  20. ^ Huff, Howard (2005). High Dielectric Constant Materials: VLSI MOSFET Applications. Springer Science & Business Media. p. 34. ISBN 9783540210818.
  21. ^ Lojek, Bo (2007). History of Semiconductor Engineering. Springer Science & Business Media. p. 120. ISBN 9783540342588.
  22. ^ U.S. Patent 2,953,486
  23. ^ a b Bassett, Ross Knox (2007). To the Digital Age: Research Labs, Start-up Companies, and the Rise of MOS Technology. Johns Hopkins University Press. p. 22. ISBN 9780801886393.
  24. ^ Atalla, M.; Kahng, D. (1960). "Silicon–silicon dioxide field induced surface devices". IRE-AIEE Solid State Device Research Conference. Carnegie Mellon University Press.
  25. ^ "Oral-History: Goldey, Hittinger and Tanenbaum". Institute of Electrical and Electronics Engineers. 25 September 2008. Retrieved 22 August 2019.
  26. ^ U.S. Patent 3,206,670 (1960)
  27. ^ U.S. Patent 3,102,230 (1960)
  28. ^ "1948 – Conception of the Junction Transistor". The Silicon Engine: A Timeline of Semiconductors in Computers. Computer History Museum. 2007.
  29. ^ Bassett, Ross Knox (2007). To the Digital Age: Research Labs, Start-up Companies, and the Rise of MOS Technology. JHU Press. pp. 42 & 332. ISBN 9780801886393.
  30. ^ a b Sah, Chih-Tang (October 1988). "Evolution of the MOS transistor-from conception to VLSI" (PDF). Proceedings of the IEEE. 76 (10): 1280–1326 (1290). doi:10.1109/5.16328. ISSN 0018-9219. Those of us active in silicon material and device research during 1956–1960 considered this successful effort by the Bell Labs group led by Atalla to stabilize the silicon surface the most important and significant technology advance, which blazed the trail that led to silicon integrated circuit technology developments in the second phase and volume production in the third phase.
  31. ^ Sah, C. T. (November 1961). "A New Semiconductor Tetrode-The Surface-Potential Controlled Transistor". Proceedings of the IRE. 49 (11): 1623–1634. doi:10.1109/JRPROC.1961.287763.
  32. ^ a b c d Butrica, Andrew J. (2015). "Chapter 3: NASA's Role in the Manufacture of Integrated Circuits" (PDF). In Dick, Steven J. (ed.). Historical Studies in the Societal Impact of Spaceflight. NASA. pp. 149-250 (239-42). ISBN 978-1-62683-027-1.
  33. ^ Bassett, Ross Knox (2007). To the Digital Age: Research Labs, Start-up Companies, and the Rise of MOS Technology. Johns Hopkins University Press. p. 3. ISBN 9780801886393.
  34. ^ Claeys, Cor L. (2003). ULSI Process Integration III: Proceedings of the International Symposium. The Electrochemical Society. p. 46. ISBN 9781566773768.
  35. ^ a b Lécuyer, Christophe (2006). Making Silicon Valley: Innovation and the Growth of High Tech, 1930-1970. Chemical Heritage Foundation. pp. 253–6 & 273. ISBN 9780262122818.
  36. ^ a b "60s Trends in the Semiconductor Industry". Semiconductor History Museum of Japan. Retrieved 7 August 2019.
  37. ^ Arns, R. G. (October 1998). "The other transistor: early history of the metal–oxide–semiconductor field-effect transistor". Engineering Science and Education Journal. 7 (5): 233–240. doi:10.1049/esej:19980509.
  38. ^ a b Chan, Yi-Jen (1992). Studies of InAIAs/InGaAs and GaInP/GaAs heterostructure FET's for high speed applications. University of Michigan. p. 1. The Si MOSFET has revolutionized the electronics industry and as a result impacts our daily lives in almost every conceivable way.
  39. ^ McCluskey, Matthew D.; Haller, Eugene E. (2012). Dopants and Defects in Semiconductors. CRC Press. p. 3. ISBN 9781439831533.
  40. ^ Daniels, Lee A. (28 May 1992). "Dr. Dawon Kahng, 61, Inventor In Field of Solid-State Electronics". The New York Times. Retrieved 1 April 2017.
  41. ^ Golio, Mike; Golio, Janet (2018). RF and Microwave Passive and Active Technologies. CRC Press. pp. 18–2. ISBN 9781420006728.
  42. ^ a b c d e f g h i j Colinge, Jean-Pierre; Greer, James C. (2016). Nanowire Transistors: Physics of Devices and Materials in One Dimension. Cambridge University Press. p. 2. ISBN 9781107052406.
  43. ^ Lamba, V.; Engles, D.; Malik, S. S.; Verma, M. (2009). "Quantum transport in silicon double-gate MOSFET". 2009 2nd International Workshop on Electron Devices and Semiconductor Technology: 1–4. doi:10.1109/EDST.2009.5166116.
  44. ^ a b c d e f Sridharan, K.; Pudi, Vikramkumar (2015). Design of Arithmetic Circuits in Quantum Dot Cellular Automata Nanotechnology. Springer. p. 1. ISBN 9783319166889.
  45. ^ a b c d e f g h i Colinge, Jean-Pierre; Colinge, C. A. (2005). Physics of Semiconductor Devices. Springer Science & Business Media. p. 165. ISBN 9780387285238.
  46. ^ Ashley, Kenneth L. (2002). Analog Electronics with LabVIEW. Prentice Hall Professional. p. 10. ISBN 9780130470652.
  47. ^ Frank, D. J.; Dennard, R. H.; Nowak, E.; Solomon, P. M.; Taur, Y. (2001). "Device scaling limits of Si MOSFETs and their application dependencies". Proceedings of the IEEE. 89 (3): 259–288. doi:10.1109/5.915374. ISSN 0018-9219.
  48. ^ Klimecky, Pete Ivan (2002). Plasma density control for reactive ion etch variation reduction in industrial microelectronics. University of Michigan. p. 2. Arguably the most important device breakthrough for the computing industry, however, occurred in 1960 when Kahng and Atalla proposed and fabricated the first metal–oxide–semiconductor field-effect-transistor, or MOSFET, using a thermally oxidized silicon structure.
  49. ^ Deal, Bruce E. (1988). "The Thermal Oxidation of Silicon and Other Semiconductor Materials". Semiconductor Materials and Process Technology Handbook: For Very Large Scale Integration (VLSI) and Ultra Large Scale Integration (ULSI) (PDF). Noyes Publications. p. 46. ISBN 9780815511502.
  50. ^ Kubozono, Yoshihiro; He, Xuexia; Hamao, Shino; Uesugi, Eri; Shimo, Yuma; Mikami, Takahiro; Goto, Hidenori; Kambe, Takashi (2015). "Application of Organic Semiconductors toward Transistors". Nanodevices for Photonics and Electronics: Advances and Applications. CRC Press. p. 355. ISBN 9789814613750.
  51. ^ Thompson, S. E.; Chau, R. S.; Ghani, T.; Mistry, K.; Tyagi, S.; Bohr, M. T. (2005). "In search of "Forever," continued transistor scaling one new material at a time". IEEE Transactions on Semiconductor Manufacturing. 18 (1): 26–36. doi:10.1109/TSM.2004.841816. ISSN 0894-6507. In the field of electronics, the planar Si metal–oxide–semiconductor field-effect transistor (MOSFET) is perhaps the most important invention.
  52. ^ Williams, J. B. (2017). The Electronics Revolution: Inventing the Future. Springer. p. 75. ISBN 9783319490885. Though these devices were not of great interest at the time, it was to be these Metal Oxide Semiconductor MOS devices that were going to have enormous impact in the future
  53. ^ Zimbovskaya, Natalya A. (2013). Transport Properties of Molecular Junctions. Springer. p. 231. ISBN 9781461480112.
  54. ^ a b c d Feldman, Leonard C. (2001). "Introduction". Fundamental Aspects of Silicon Oxidation. Springer Science & Business Media. pp. 1–11. ISBN 9783540416821.
  55. ^ a b c Dabrowski, Jarek; Müssig, Hans-Joachim (2000). "1.2. The Silicon Age". Silicon Surfaces and Formation of Interfaces: Basic Science in the Industrial World. World Scientific. pp. 3–13. ISBN 9789810232863.
  56. ^ Malmstadt, Howard V.; Enke, Christie G.; Crouch, Stanley R. (1994). Making the Right Connections: Microcomputers and Electronic Instrumentation. American Chemical Society. p. 389. ISBN 9780841228610. The relative simplicity and low power requirements of MOSFETs have fostered today's microcomputer revolution.
  57. ^ Wong, Kit Po (2009). Electrical Engineering - Volume II. EOLSS Publications. p. 7. ISBN 9781905839780.
  58. ^ "Transistors - an overview". ScienceDirect. Retrieved 8 August 2019.
  59. ^ Raymer, Michael G. (2009). The Silicon Web: Physics for the Internet Age. CRC Press. p. 365. ISBN 9781439803127.
  60. ^ a b c d "Remarks by Director Iancu at the 2019 International Intellectual Property Conference". United States Patent and Trademark Office. June 10, 2019. Retrieved 20 July 2019.
  61. ^ Fossum, Jerry G.; Trivedi, Vishal P. (2013). Fundamentals of Ultra-Thin-Body MOSFETs and FinFETs. Cambridge University Press. p. vii. ISBN 9781107434493.
  62. ^ Chen, Wai Kai (2004). The Electrical Engineering Handbook. Elsevier. p. 109. ISBN 9780080477480.
  63. ^ Franco, Jacopo; Kaczer, Ben; Groeseneken, Guido (2013). Reliability of High Mobility SiGe Channel MOSFETs for Future CMOS Applications. Springer Science & Business Media. pp. 1–2. ISBN 9789400776630.
  64. ^ a b c d e f g "13 Sextillion & Counting: The Long & Winding Road to the Most Frequently Manufactured Human Artifact in History". Computer History Museum. April 2, 2018. Retrieved 28 July 2019.
  65. ^ a b c d e f Baker, R. Jacob (2011). CMOS: Circuit Design, Layout, and Simulation. John Wiley & Sons. p. 7. ISBN 978-1118038239.
  66. ^ Maloberti, Franco; Davies, Anthony C. (2016). A Short History of Circuits and Systems: From Green, Mobile, Pervasive Networking to Big Data Computing (PDF). IEEE Circuits and Systems Society. pp. 65–6. ISBN 9788793609860.
  67. ^ Schwierz, Frank; Wong, Hei; Liou, Juin J. (2010). Nanometer CMOS. Pan Stanford Publishing. p. 5. ISBN 9789814241083.
  68. ^ Ye, Peide; Ernst, Thomas; Khare, Mukesh V. (30 July 2019). "The Nanosheet Transistor Is the Next (and Maybe Last) Step in Moore's Law". IEEE Spectrum. Retrieved 6 November 2019.
  69. ^ a b c d e f Whiteley, Carol; McLaughlin, John Robert (2002). Technology, Entrepreneurs, and Silicon Valley. Institute for the History of Technology. ISBN 9780964921719. These active electronic components, or power semiconductor products, from Siliconix are used to switch and convert power in a wide range of systems, from portable information appliances to the communications infrastructure that enables the Internet. The company's power MOSFETs — tiny solid-state switches, or metal oxide semiconductor field-effect transistors — and power integrated circuits are widely used in cell phones and notebook computers to manage battery power efficiently
  70. ^ a b c Omura, Yasuhisa; Mallik, Abhijit; Matsuo, Naoto (2017). MOS Devices for Low-Voltage and Low-Energy Applications. John Wiley & Sons. p. 53. ISBN 9781119107354.
  71. ^ a b c d e f g Baliga, B. Jayant (2005). Silicon RF Power MOSFETS. World Scientific. ISBN 9789812561213.
  72. ^ a b c d e f g h i Asif, Saad (2018). 5G Mobile Communications: Concepts and Technologies. CRC Press. pp. 128–134. ISBN 9780429881343.
  73. ^ a b c Jindal, R. P. (2009). "From millibits to terabits per second and beyond - Over 60 years of innovation". 2009 2nd International Workshop on Electron Devices and Semiconductor Technology: 1–6. doi:10.1109/EDST.2009.5166093.
  74. ^ a b c d e Lindley, David (15 May 2015). "Focus: Landmarks—Accidental Discovery Leads to Calibration Standard". Physics. 8.
  75. ^ a b c d e f g Williams, J. B. (2017). The Electronics Revolution: Inventing the Future. Springer. pp. 245, 249–50. ISBN 9783319490885.
  76. ^ Woodall, Jerry M. (2010). Fundamentals of III-V Semiconductor MOSFETs. Springer Science & Business Media. p. 2. ISBN 9781441915474.
  77. ^ a b c "Advanced information on the Nobel Prize in Physics 2000" (PDF). Nobel Prize. June 2018. Retrieved 17 August 2019.
  78. ^ "Milestones:List of IEEE Milestones". Institute of Electrical and Electronics Engineers. Retrieved 25 July 2019.
  79. ^ a b c d e "MOSFET DIFFERENTIAL AMPLIFIER" (PDF). Boston University. Retrieved 10 August 2019.
  80. ^ a b c d e "MDmesh: 20 Years of Superjunction STPOWER™ MOSFETs, A Story About Innovation". ST Microelectronics. 11 September 2019. Retrieved 2 November 2019.
  81. ^ a b c d e f g h i j k l m n o p q r s t u v Veendrick, Harry J. M. (2017). Nanometer CMOS ICs: From Basics to ASICs (2nd ed.). Springer. p. 315. ISBN 9783319475974.
  82. ^ Major, Liam (1 December 2018). "What is an Airsoft Mosfet? An Airsof Mosfet Inroduction". Major Airsoft. Retrieved 11 November 2019.
  83. ^ a b c d "Applying MOSFETs to Today's Power-Switching Designs". Electronic Design. 23 May 2016. Retrieved 10 August 2019.
  84. ^ a b c d e Veendrick, Harry (2000). Deep-Submicron CMOS ICs: From Basics to ASICs (PDF) (2nd ed.). Kluwer Academic Publishers. p. 220. ISBN 9044001116.
  85. ^ a b c d e f g h i j k l Mead, Carver A.; Ismail, Mohammed, eds. (May 8, 1989). Analog VLSI Implementation of Neural Systems (PDF). Norwell, MA: Kluwer Academic Publishers. doi:10.1007/978-1-4613-1639-8. ISBN 978-1-4613-1639-8.
  86. ^ a b Morgado, Alonso; Río, Rocío del; Rosa, José M. de la (2011). Nanometer CMOS Sigma-Delta Modulators for Software Defined Radio. Springer Science & Business Media. ISBN 9781461400370.
  87. ^ M. Holler, S. Tam, H. Castro, and R. Benson, "An electrically trainable artificial neural network with 10240 'floating gate' synapses", Proceedings of the International Joint Conference on Neural Networks, Washington, D.C., vol. II, 1989, pp. 191–196
  88. ^ a b c d e f g h i j k Chee, Kuan W. A.; Ye, Tianhong (August 2018). "Towards New Generation Power MOSFETs for Automotive Electric Control Units". Complementary Metal Oxide Semiconductor. pp. 129–32. doi:10.5772/intechopen.70906. ISBN 9781789234961.
  89. ^ a b c d e f g Veendrick, Harry J. M. (2017). Nanometer CMOS ICs: From Basics to ASICs. Springer. p. 245. ISBN 9783319475974.
  90. ^ a b Duncan, Ben (1996). High Performance Audio Power Amplifiers (PDF). Elsevier. pp. 177–8, 406. ISBN 9780080508047.
  91. ^ a b c d e f g h i j "Design News". Design News. Cahners Publishing Company. 27 (1–8): 275. 1972. Today, under contracts with some 20 major companies, we're working on nearly 30 product programs—applications of MOS/LSI technology for automobiles, trucks, appliances, business machines, musical instruments, computer peripherals, cash registers, calculators, data transmission and telecommunication equipment.
  92. ^ a b c "Automotive Power MOSFETs" (PDF). Fuji Electric. Retrieved 10 August 2019.
  93. ^ a b c d Frank, Randy (1 November 2005). "Top 30 Power Milestones and Products". Power Electronics. Retrieved 16 November 2019.
  94. ^ a b Emadi, Ali (2017). Handbook of Automotive Power Electronics and Motor Drives. CRC Press. p. 117. ISBN 9781420028157.
  95. ^ a b c d e f g h i j "CMOS Sensors Enable Phone Cameras, HD Video". NASA Spinoff. NASA. Retrieved 6 November 2019.
  96. ^ a b c d e f "NIHF Inductee Bantval Jayant Baliga Invented IGBT Technology". National Inventors Hall of Fame. Retrieved 17 August 2019.
  97. ^ a b c Gosden, D.F. (March 1990). "Modern Electric Vehicle Technology using an AC Motor Drive". Journal of Electrical and Electronics Engineering. Institution of Engineers Australia. 10 (1): 21–7. ISSN 0725-2986.
  98. ^ a b c d Schöning, Michael J.; Poghossian, Arshak (10 September 2002). "Recent advances in biologically sensitive field-effect transistors (BioFETs)" (PDF). Analyst. 127 (9): 1137–1151. doi:10.1039/B204444G. ISSN 1364-5528.
  99. ^ a b c d e f g h i j k Omura, Yasuhisa; Mallik, Abhijit; Matsuo, Naoto (2017). MOS Devices for Low-Voltage and Low-Energy Applications. John Wiley & Sons. pp. 3–4. ISBN 9781119107354.
  100. ^ a b c Hittinger, William C. (1973). "Metal–Oxide–Semiconductor Technology". Scientific American. 229 (2): 48–59. Bibcode:1973SciAm.229b..48H. doi:10.1038/scientificamerican0873-48. ISSN 0036-8733. JSTOR 24923169.
  101. ^ a b c d e f g h i j k l m Veendrick, Harry (2000). Deep-Submicron CMOS ICs: From Basics to ASICs (PDF) (2nd ed.). Kluwer Academic Publishers. pp. 337–8. ISBN 9044001116.
  102. ^ a b Business Automation. Hitchcock Publishing Company. 1972. p. 28. In addition, electro-optical technology and MOS/LSI electronics combine to provide a highly accurate embossed credit card reader which can be part of a POS terminal or standalone unit. It detects embossed numbers for direct checking with a central computer to verify a customer's credit and initiate the purchasing transaction. Also, the same electronics can be used to read data contained on magnetic tape and other types of credit card
  103. ^ a b Klinger, A.; Fu, K. S.; Kunii, T. L. (2014). Data Structures, Computer Graphics, and Pattern Recognition. Academic Press. p. 331. ISBN 9781483267258.
  104. ^ a b c Grabinski, Wladyslaw; Gneiting, Thomas (2010). POWER/HVMOS Devices Compact Modeling. Springer Science & Business Media. pp. 33–4. ISBN 9789048130467.
  105. ^ a b Oliveira, Joao; Goes, João (2012). Parametric Analog Signal Amplification Applied to Nanoscale CMOS Technologies. Springer Science & Business Media. p. 7. ISBN 9781461416708.
  106. ^ Baker, R. Jacob (2011). CMOS: Circuit Design, Layout, and Simulation. John Wiley & Sons. ISBN 9781118038239.
  107. ^ a b c d e f Grant, Duncan Andrew; Gowar, John (1989). Power MOSFETS: theory and applications. Wiley. p. 1. ISBN 9780471828679. The metal–oxide–semiconductor field-effect transistor (MOSFET) is the most commonly used active device in the very-large-scale integration of digital integrated circuits (VLSI). During the 1970s these components revolutionized electronic signal processing, control systems and computers.
  108. ^ a b c Jacob, J. (2001). Power Electronics: Principles and Applications. Cengage Learning. p. 280. ISBN 9780766823327.
  109. ^ a b c d Omura, Yasuhisa; Mallik, Abhijit; Matsuo, Naoto (2017). MOS Devices for Low-Voltage and Low-Energy Applications. John Wiley & Sons. ISBN 9781119107354.
  110. ^ a b Proceedings of the Ninth International Symposium on Silicon-on-Insulator Technology and Devices. The Electrochemical Society. 1999. p. 305. ISBN 9781566772259.
  111. ^ a b c Cherry, Robert William (June 1973). "A calculator option for the Tektronix 4010 computer graphics terminal". Compilation of Abstracts of Dissertations, Theses and Research Papers Submitted by Candidates for Degrees. Naval Postgraduate School.
  112. ^ Lewallen, D. R. (1969). Mos LSI computer aided design system. DAC '69 Proceedings of the 6th annual Design Automation Conference. pp. 91–101. doi:10.1145/800260.809019.
  113. ^ Van Beek, H. W. (May 1972). Computer-aided design of MOS/LSI circuits. AFIPS '72 (Spring) Proceedings of the May 16-18, 1972, spring joint computer conference. pp. 1059–1063. doi:10.1145/1478873.1479014.
  114. ^ a b c O'Regan, Gerard (2016). Introduction to the History of Computing: A Computing History Primer. Springer. p. 132. ISBN 9783319331386.
  115. ^ a b c d e Waclawek, Jan (2006). Culver, John (ed.). "The Unofficial History of 8051". The CPU Shack Museum. Retrieved 15 November 2019.
  116. ^ Parslow, R. (2013). Computer Graphics: Techniques and Applications. Springer Science & Business Media. p. 96. ISBN 9781475713206.
  117. ^ "MOSFET: Toward the Scaling Limit". Semiconductor Technology Online. Retrieved 29 July 2019.
  118. ^ a b Harding, Scharon (September 17, 2019). "What Is a MOSFET? A Basic Definition". Tom's Hardware. Retrieved 7 November 2019.
  119. ^ a b c Veendrick, Harry J. M. (2017). Nanometer CMOS ICs: From Basics to ASICs (2nd ed.). Springer. p. 264. ISBN 9783319475974.
  120. ^ a b c d e Amos, S. W.; James, Mike (2013). Principles of Transistor Circuits: Introduction to the Design of Amplifiers, Receivers and Digital Circuits. Elsevier. p. 332. ISBN 9781483293905.
  121. ^ a b Colinge, Jean-Pierre; Greer, Jim (2010). "Chapter 12: Transistor Structures for Nanoelectronics". Handbook of Nanophysics: Nanoelectronics and Nanophotonics. CRC Press. p. 12-1. ISBN 9781420075519.
  122. ^ a b Lyon, Richard F. (2014). "The Optical Mouse: Early Biomimetic Embedded Vision". Advances in Embedded Computer Vision. Springer. pp. 3-22 (3). ISBN 9783319093871.
  123. ^ a b Lyon, Richard F. (August 1981). "The Optical Mouse, and an Architectural Methodology for Smart Digital Sensors" (PDF). In H. T. Kung; Robert F. Sproull; Guy L. Steele (eds.). VLSI Systems and Computations. Computer Science Press. doi:10.1007/978-3-642-68402-9_1.
  124. ^ a b c d e f g h Veendrick, Harry (2000). Deep-Submicron CMOS ICs: From Basics to ASICs (PDF) (2nd ed.). Kluwer Academic Publishers. pp. 273–82. ISBN 9044001116.
  125. ^ a b Kimizuka, Noboru; Yamazaki, Shunpei (2016). Physics and Technology of Crystalline Oxide Semiconductor CAAC-IGZO: Fundamentals. John Wiley & Sons. p. 217. ISBN 9781119247401.
  126. ^ a b c Shanmugam, S. (2019). Nanotechnology. MJP Publisher. p. 83.
  127. ^ "1979: Single Chip Digital Signal Processor Introduced". The Silicon Engine. Computer History Museum. Retrieved 2019-05-13.
  128. ^ "DSPs: Back to the Future". ACM Queue. 2 (1). April 16, 2004. Retrieved 14 October 2019.
  129. ^ a b c d e f g h Bergveld, Piet (October 1985). "The impact of MOSFET-based sensors" (PDF). Sensors and Actuators. 8 (2): 109–127. doi:10.1016/0250-6874(85)87009-8. ISSN 0250-6874.
  130. ^ a b c "1971: Reusable semiconductor ROM introduced". Computer History Museum. Retrieved 19 June 2019.
  131. ^ a b c Bez, R.; Pirovano, A. (2019). Advances in Non-Volatile Memory and Storage Technology. Woodhead Publishing. ISBN 9780081025857.
  132. ^ Hutchinson, Lee (4 June 2012). "Solid-state revolution: in-depth on how SSDs really work". Ars Technica. Retrieved 27 September 2019.
  133. ^ a b c Iniewski, Krzysztof (2010). CMOS Processors and Memories. Springer Science & Business Media. ISBN 9789048192168.
  134. ^ a b c d e Brotherton, S. D. (2013). Introduction to Thin Film Transistors: Physics and Technology of TFTs. Springer Science & Business Media. ISBN 9783319000022.
  135. ^ Winder, Steve (2011). Power Supplies for LED Driving. Newnes. pp. 20–22, 39–41. ISBN 9780080558578.
  136. ^ a b c Kuo, Y. (2008). Thin Film Transistors 9 (TFT 9). The Electrochemical Society. p. 365. ISBN 9781566776554.
  137. ^ a b c Kuo, Yue (1 January 2013). "Thin Film Transistor Technology—Past, Present, and Future" (PDF). The Electrochemical Society Interface. 22 (1): 55–61. doi:10.1149/2.F06131if. ISSN 1064-8208.
  138. ^ U.S. Patent 5,598,285: K. Kondo, H. Terao, H. Abe, M. Ohta, K. Suzuki, T. Sasaki, G. Kawachi, J. Ohwada, Liquid crystal display device, filed Sep 18, 1992 and Jan 20, 1993.
  139. ^ a b c d e f Shirriff, Ken (30 August 2016). "The Surprising Story of the First Microprocessors". IEEE Spectrum. Institute of Electrical and Electronics Engineers. Retrieved 13 October 2019.
  140. ^ Iniewski, Krzysztof, ed. (2010). CMOS Processors and Memories. Springer Science & Business Media. p. 4. ISBN 9789048192168.
  141. ^ a b Rai-Choudhury, P. (2000). MEMS and MOEMS Technology and Applications. SPIE Press. pp. ix, 3, . ISBN 9780819437167.CS1 maint: extra punctuation (link)
  142. ^ a b "Infineon Hits Bulk-CMOS RF Switch Milestone". EE Times. 20 November 2018. Retrieved 26 October 2019.
  143. ^ a b Memories: A Personal History of Bell Telephone Laboratories (PDF). Institute of Electrical and Electronics Engineers. 2011. p. 59. ISBN 1463677979.
  144. ^ a b c d O'Neill, A. (2008). "Asad Abidi Recognized for Work in RF-CMOS". IEEE Solid-State Circuits Society Newsletter. 13 (1): 57–58. doi:10.1109/N-SSC.2008.4785694. ISSN 1098-4232.
  145. ^ "1967: Application Specific Integrated Circuits employ Computer-Aided Design". The Silicon Engine. Computer History Museum. Retrieved 9 November 2019.
  146. ^ Lin, Youn-Long Steve (2007). Essential Issues in SOC Design: Designing Complex Systems-on-Chip. Springer Science & Business Media. p. 176. ISBN 9781402053528.
  147. ^ Veendrick, Harry (2000). Deep-Submicron CMOS ICs: From Basics to ASICs (PDF) (2nd ed.). Kluwer Academic Publishers. p. 466. ISBN 9044001116.
  148. ^ Veendrick, Harry J. M. (2017). Nanometer CMOS ICs: From Basics to ASICs (2nd ed.). Springer. pp. 314–5. ISBN 9783319475974.
  149. ^ a b c Solid State Design - Vol. 6. Horizon House. 1965.
  150. ^ a b Powers, E.; Zimmermann, M. (1968). TADIM—A Digital Implementation of a Multichannel Data Modem. International Conference on Communications. IEEE. p. 706. With the advent of digital microelectronic integrated circuits and MOS FET shift register memories the application of "wholesale" technology to the implementation of a digital multichannel modem became extremely attractive for providing the advantages of extremely small size, light weight, high reliability and low cost, in addition to the inherent stability and freedom from adjustment provided by digital circuitry.
  151. ^ Sun, Jianhai; Geng, Zhaoxin; Xue, Ning; Liu, Chunxiu; Ma, Tianjun (17 August 2018). "A Mini-System Integrated with Metal–Oxide–Semiconductor Sensor and Micro-Packed Gas Chromatographic Column". Micromachines. 9 (8). doi:10.3390/mi9080408. ISSN 2072-666X.
  152. ^ a b c Veendrick, Harry (2000). Deep-Submicron CMOS ICs: From Basics to ASICs (PDF) (2nd ed.). Kluwer Academic Publishers. p. 215. ISBN 9044001116.
  153. ^ a b c d e Tsu‐Jae King, Liu (June 11, 2012). "FinFET: History, Fundamentals and Future". University of California, Berkeley. Symposium on VLSI Technology Short Course. Archived from the original on 28 May 2016. Retrieved 9 July 2019.
  154. ^ a b "Complementary metal oxide semiconductor - an overview". ScienceDirect. Retrieved 21 November 2019.
  155. ^ Patel, Mukund R. (2004). Spacecraft Power Systems. CRC Press. p. 97. ISBN 9781420038217.
  156. ^ Kularatna, Nihal (2000). Modern Component Families and Circuit Block Design. Newnes. p. 33. ISBN 9780750699921.
  157. ^ "Rethink Power Density with GaN". Electronic Design. 21 April 2017. Retrieved 23 July 2019.
  158. ^ a b Meltzer, Michael (2015). The Cassini-Huygens Visit to Saturn: An Historic Mission to the Ringed Planet. Springer. p. 70. ISBN 9783319076089.
  159. ^ Ali Emadi (2009). Integrated power electronic converters and digital control. CRC Press. pp. 145–146. ISBN 978-1-4398-0069-0.
  160. ^ a b "Power Supply Technology - Buck DC/DC Converters". Mouser Electronics. Retrieved 11 August 2019.
  161. ^ a b K. v. Klitzing; G. Dorda; M. Pepper (1980). "New method for high-accuracy determination of the fine-structure constant based on quantized Hall resistance". Phys. Rev. Lett. 45 (6): 494–497. Bibcode:1980PhRvL..45..494K. doi:10.1103/PhysRevLett.45.494.
  162. ^ Gilder, George (1990). Microcosm: The Quantum Revolution In Economics And Technology. Simon and Schuster. pp. 86–9, 95, 145–8, 300. ISBN 9780671705923.
  163. ^ a b c Veendrick, Harry J. M. (2017). Nanometer CMOS ICs: From Basics to ASICs (2nd ed.). Springer. p. 243. ISBN 9783319475974.
  164. ^ a b c Voinigescu, Sorin (2013). High-Frequency Integrated Circuits. Cambridge University Press. ISBN 9780521873024.
  165. ^ a b Fralick, Stanley C.; Brandin, David H.; Kuo, Franklin F.; Harrison, Christopher (May 19–22, 1975). Digital Terminals For Packet Broadcasting (PDF). AFIPS '75. American Federation of Information Processing Societies. doi:10.1145/1499949.1499990.CS1 maint: date format (link)
  166. ^ a b "Robert Dennard". Encyclopedia Britannica. Retrieved 8 July 2019.
  167. ^ Veendrick, Harry J. M. (2017). Nanometer CMOS ICs: From Basics to ASICs (2nd ed.). Springer. pp. 305–6. ISBN 9783319475974.
  168. ^ a b c d Veendrick, Harry J. M. (2017). Nanometer CMOS ICs: From Basics to ASICs (2nd ed.). Springer. pp. 276–9. ISBN 9783319475974.
  169. ^ a b Sahay, Shubham; Kumar, Mamidala Jagadesh (2019). Junctionless Field-Effect Transistors: Design, Modeling, and Simulation. John Wiley & Sons. ISBN 9781119523536.
  170. ^ a b c d Interplanetary Monitoring Platform (PDF). NASA. 29 August 1989. pp. 1, 11, 134. Retrieved 12 August 2019.
  171. ^ a b White, H. D.; Lokerson, D. C. (1971). "The Evolution of IMP Spacecraft Mosfet Data Systems". IEEE Transactions on Nuclear Science. 18 (1): 233–236. doi:10.1109/TNS.1971.4325871. ISSN 0018-9499.
  172. ^ Chapuis, Robert J.; Joel, Amos E. (2003). 100 Years of Telephone Switching. IOS Press. pp. 21, 135, 141–6, 214. ISBN 9781586033729.
  173. ^ Gibson, Jerry D. (2018). The Communications Handbook. CRC Press. p. 34-4. ISBN 9781420041163.
  174. ^ "Computerworld". Computerworld. IDG Enterprise. 6 (48): 34. 29 November 1972. ISSN 0010-4841.
  175. ^ Macchiolo, A.; Andricek, L.; Moser, H. G.; Nisius, R.; Richter, R. H.; Weigell, P. (1 January 2012). "SLID-ICV Vertical Integration Technology for the ATLAS Pixel Upgrades" (PDF). Physics Procedia. 37: 1009–1015. doi:10.1016/j.phpro.2012.02.444. ISSN 1875-3892.
  176. ^ Kent, Joel (May 2010). "Touchscreen technology basics & a new development". CMOS Emerging Technologies Conference. CMOS Emerging Technologies Research. 6: 1–13.
  177. ^ "Carroll Releases ASIC-Based Touch System Controller". InfoWorld. InfoWorld Media Group. 10 (12): 34. 21 March 1988. ISSN 0199-6649.
  178. ^ Ballou, Glen (2013). Handbook for Sound Engineers. Taylor & Francis. ISBN 9781136122538.
  179. ^ Richard Shoup (2001). "SuperPaint: An Early Frame Buffer Graphics System" (PDF). Annals of the History of Computing. IEEE. Archived from the original (PDF) on 2004-06-12.
  180. ^ Goldwasser, S.M. (June 1983). Computer Architecture For Interactive Display Of Segmented Imagery. Computer Architectures for Spatially Distributed Data. Springer Science & Business Media. pp. 75-94 (81). ISBN 9783642821509.
  181. ^ Peddie, Jon. "Famous Graphics Chips: TI TMS34010 and VRAM". IEEE Computer Society. Institute of Electrical and Electronics Engineers. Retrieved 1 November 2019.
  182. ^ Stephens, Carlene; Dennis, Maggie (2000). "Engineering Time: Inventing the Electronic Wristwatch" (PDF). The British Journal for the History of Science. Cambridge University Press. 33 (4): 477–497 (485). ISSN 0007-0874.
  183. ^ "Early 1970s: Evolution of CMOS LSI circuits for watches" (PDF). Semiconductor History Museum of Japan. Retrieved 6 July 2019.
  184. ^ Srivastava, Viranjay M.; Singh, Ghanshyam (2013). MOSFET Technologies for Double-Pole Four-Throw Radio-Frequency Switch. Springer Science & Business Media. p. 1. ISBN 9783319011653.
  185. ^ Chen, Wai-Kai (2018). The VLSI Handbook. CRC Press. p. 60-2. ISBN 9781420005967.
  186. ^ Morgado, Alonso; Río, Rocío del; Rosa, José M. de la (2011). Nanometer CMOS Sigma-Delta Modulators for Software Defined Radio. Springer Science & Business Media. p. 1. ISBN 9781461400370.
  187. ^ Daneshrad, Babal; Eltawil, Ahmed M. (2002). "Integrated Circuit Technologies for Wireless Communications". Wireless Multimedia Network Technologies. Springer US: 227–244. doi:10.1007/0-306-47330-5_13.
  188. ^ Nathawad, L.; Zargari, M.; Samavati, H.; Mehta, S.; Kheirkhaki, A.; Chen, P.; Gong, K.; Vakili-Amini, B.; Hwang, J.; Chen, M.; Terrovitis, M.; Kaczynski, B.; Limotyrakis, S.; Mack, M.; Gan, H.; Lee, M.; Abdollahi-Alibeik, B.; Baytekin, B.; Onodera, K.; Mendis, S.; Chang, A.; Jen, S.; Su, D.; Wooley, B. "20.2: A Dual-band CMOS MIMO Radio SoC for IEEE 802.11n Wireless LAN" (PDF). IEEE Entity Web Hosting. IEEE. Retrieved 22 October 2016.
  189. ^ "Abidi Receives IEEE Pederson Award at ISSCC 2008" (PDF). SSCC: IEEE Solid-State Circuits Society News. 13 (2): 12. Spring 2008.
  190. ^ Lança, Luís; Silva, Augusto (2013). "Digital Radiography Detectors: A Technical Overview". Digital imaging systems for plain radiography. New York: Springer. pp. 14–17. doi:10.1007/978-1-4614-5067-2_2. hdl:10400.21/1932. ISBN 978-1-4614-5066-5.
  191. ^ Kump, K; Grantors, P; Pla, F; Gobert, P (December 1998). "Digital X-ray detector technology". RBM-News. 20 (9): 221–226. doi:10.1016/S0222-0776(99)80006-6.
  192. ^ "Intel 45nm Hi-k Silicon Technology". Archived from the original on October 6, 2009.
  193. ^ "memory components data book" (PDF). memory components data book. Intel. pp. 2–1. Archived from the original (PDF) on 4 March 2016. Retrieved 30 August 2015.
  194. ^ "Using a MOSFET as a Switch". 090507 brunningsoftware.co.uk
  195. ^ Shichman, H. & Hodges, D. A. (1968). "Modeling and simulation of insulated-gate field-effect transistor switching circuits". IEEE Journal of Solid-State Circuits. SC-3 (3): 285–289. Bibcode:1968IJSSC...3..285S. doi:10.1109/JSSC.1968.1049902.
  196. ^ For example, see Cheng, Yuhua; Hu, Chenming (1999). MOSFET modeling & BSIM3 user's guide. Springer. ISBN 978-0-7923-8575-2.. The most recent version of the BSIM model is described in V., Sriramkumar; Paydavosi, Navid; Lu, Darsen; Lin, Chung-Hsun; Dunga, Mohan; Yao, Shijing; Morshed, Tanvir; Niknejad, Ali & Hu, Chenming (2012). "BSIM-CMG 106.1.0beta Multi-Gate MOSFET Compact Model" (PDF). Department of EE and CS, UC Berkeley. Archived from the original (PDF) on 2014-07-27. Retrieved 2012-04-01.
  197. ^ Gray, P. R.; Hurst, P. J.; Lewis, S. H. & Meyer, R. G. (2001). Analysis and Design of Analog Integrated Circuits (Fourth ed.). New York: Wiley. pp. 66–67. ISBN 978-0-471-32168-2.
  198. ^ van der Meer, P. R.; van Staveren, A.; van Roermund, A. H. M. (2004). Low-Power Deep Sub-Micron CMOS Logic: Subthreshold Current Reduction. Dordrecht: Springer. p. 78. ISBN 978-1-4020-2848-9.
  199. ^ Degnan, Brian. "Wikipedia fails subvt".
  200. ^ Mead, Carver (1989). Analog VLSI and Neural Systems. Reading, MA: Addison-Wesley. p. 370. ISBN 9780201059922.
  201. ^ Smith, Leslie S.; Hamilton, Alister (1998). Neuromorphic Systems: Engineering Silicon from Neurobiology. World Scientific. pp. 52–56. ISBN 978-981-02-3377-8.
  202. ^ Kumar, Satish (2004). Neural Networks: A Classroom Approach. Tata McGraw-Hill. p. 688. ISBN 978-0-07-048292-0.
  203. ^ Glesner, Manfred; Zipf, Peter; Renovell, Michel (2002). Field-programmable Logic and Applications: 12th International Conference. Dordrecht: Springer. p. 425. ISBN 978-3-540-44108-3.
  204. ^ Vittoz, Eric A. (1996). "The Fundamentals of Analog Micropower Design". In Toumazou, Chris; Battersby, Nicholas C.; Porta, Sonia (eds.). Circuits and systems tutorials. John Wiley and Sons. pp. 365–372. ISBN 978-0-7803-1170-1.
  205. ^ Shukla, Sandeep K.; Bahar, R. Iris (2004). Nano, Quantum and Molecular Computing. Springer. p. 10 and Fig. 1.4, p. 11. ISBN 978-1-4020-8067-8.
  206. ^ Srivastava, Ashish; Sylvester, Dennis; Blaauw, David (2005). Statistical Analysis and Optimization For VLSI: Timing and Power. Springer. p. 135. ISBN 978-0-387-25738-9.
  207. ^ Galup-Montoro, C. & M.C., Schneider (2007). MOSFET modeling for circuit analysis and design. London/Singapore: World Scientific. p. 83. ISBN 978-981-256-810-6.
  208. ^ Malik, Norbert R. (1995). Electronic circuits: analysis, simulation, and design. Englewood Cliffs, NJ: Prentice Hall. pp. 315–316. ISBN 978-0-02-374910-0.
  209. ^ Gray, P. R.; Hurst, P. J.; Lewis, S. H.; Meyer, R. G. (2001). §1.5.2 p. 45. ISBN 978-0-471-32168-2.
  210. ^ Sedra, A. S. & Smith, K. C. (2004). Microelectronic circuits (Fifth ed.). New York: Oxford. p. 552. ISBN 978-0-19-514251-8.
  211. ^ Sedra, A. S. & Smith, K.C. (2004). p. 250, Eq. 4.14. ISBN 978-0-19-514251-8.
  212. ^ For a uniformly doped p-type substrate with bulk acceptor doping of NA per unit volume,
    with ni the intrinsic mobile carrier density per unit volume in the bulk. See, for example, Arora, Narain (2007). "Equation 5.12". Mosfet modeling for VLSI simulation: theory and practice. World Scientific. p. 173. ISBN 978-981-256-862-5.
  213. ^ "Body effect". Equars.com. Archived from the original on 2014-11-10. Retrieved 2012-06-02.
  214. ^ "Electronic Circuit Symbols". circuitstoday.com. 9 November 2011. Archived from the original on 13 October 2014.
  215. ^ IEEE Std 315-1975 — Graphic Symbols for Electrical and Electronics Diagrams (Including Reference Designation Letters)
  216. ^ Jaeger, Richard C.; Blalock, Travis N. "Figure 4.15 IEEE Standard MOS transistor circuit symbols" (PDF). Microelectronic Circuit Design.
  217. ^ Voinigescu, Sorin (2013). High-Frequency Integrated Circuits. Cambridge University Press. p. 164. ISBN 9780521873024.
  218. ^ Sze, Simon M. (2002). Semiconductor Devices: Physics and Technology (PDF) (2nd ed.). Wiley. p. 4. ISBN 0-471-33372-7.
  219. ^ "Computer History Museum – The Silicon Engine | 1963 – Complementary MOS Circuit Configuration is Invented". Computerhistory.org. Retrieved 2012-06-02.
  220. ^ a b "1963: Complementary MOS Circuit Configuration is Invented". Computer History Museum. Retrieved 6 July 2019.
  221. ^ "Depletion Mode". Techweb. Techweb. 29 January 2010. Retrieved 27 November 2010.
  222. ^ "MIS". Semiconductor Glossary.
  223. ^ Hadziioannou, Georges; Malliaras, George G. (2007). Semiconducting polymers: chemistry, physics and engineering. Wiley-VCH. ISBN 978-3-527-31271-9.
  224. ^ a b Jones, William (1997). Organic Molecular Solids: Properties and Applications. CRC Press. ISBN 978-0-8493-9428-7.
  225. ^ Xu, Wentao; Guo, Chang; Rhee, Shi-Woo (2013). "High performance organic field-effect transistors using cyanoethyl pullulan (CEP) high-k polymer cross-linked with trimethylolpropane triglycidyl ether (TTE) at low temperatures". Journal of Materials Chemistry C. 1 (25): 3955. doi:10.1039/C3TC30134F.
  226. ^ D. Kahng and S. M. Sze, "A floating-gate and its application to memory devices", The Bell System Technical Journal, vol. 46, no. 4, 1967, pp. 1288–1295
  227. ^ Baliga, B. Jayant (1996). Power Semiconductor Devices. Boston: PWS publishing Company. ISBN 978-0-534-94098-0.
  228. ^ "Power MOSFET Basics: Understanding MOSFET Characteristics Associated With The Figure of Merit". element14. Archived from the original on 5 April 2015. Retrieved 27 November 2010.
  229. ^ "Power MOSFET Basics: Understanding Gate Charge and Using It To Assess Switching Performance". element14. Archived from the original on 30 June 2014. Retrieved 27 November 2010.
  230. ^ Irwin, J. David (1997). The Industrial Electronics Handbook. CRC Press. p. 218. ISBN 9780849383434.
  231. ^ a b "Power MOSFET Basics" (PDF). Alpha & Omega Semiconductor. Retrieved 29 July 2019.
  232. ^ Hu, Chenming (February 13, 2009). "MOS Capacitor" (PDF). UC Berkeley. Retrieved 6 October 2019.
  233. ^ Sze, Simon Min; Lee, Ming-Kwei (May 2012). "MOS Capacitor and MOSFET". Semiconductor Devices: Physics and Technology. John Wiley & Sons. ISBN 9780470537947. Retrieved 6 October 2019.
  234. ^ Sze, Simon M. (2002). Semiconductor Devices: Physics and Technology (PDF) (2nd ed.). Wiley. p. 214. ISBN 0-471-33372-7.
  235. ^ Weimer, Paul K. (1962). "The TFT A New Thin-Film Transistor". Proceedings of the IRE. 50 (6): 1462–1469. doi:10.1109/JRPROC.1962.288190. ISSN 0096-8390.
  236. ^ Kawamoto, H. (2012). "The Inventors of TFT Active-Matrix LCD Receive the 2011 IEEE Nishizawa Medal". Journal of Display Technology. 8 (1): 3–4. doi:10.1109/JDT.2011.2177740. ISSN 1551-319X.
  237. ^ Castellano, Joseph A. (2005). Liquid Gold: The Story of Liquid Crystal Displays and the Creation of an Industry. World Scientific. pp. 176–7. ISBN 9789812389565.
  238. ^ Alvarez, Antonio R. (1990). "Introduction To BiCMOS". BiCMOS Technology and Applications. Springer Science & Business Media. pp. 1-20 (2). doi:10.1007/978-1-4757-2029-7_1. ISBN 9780792393849.
  239. ^ "IGBT Definition". PC Magazine Encyclopedia. PC Magazine. Retrieved 17 August 2019.
  240. ^ Chris Toumazou; Pantelis Georgiou (December 2011). "40 years of ISFET technology:From neuronal sensing to DNA sequencing". Electronics Letters. Retrieved 13 May 2016.
  241. ^ Zeitzoff, P. M.; Hutchby, J. A.; Huff, H. R. (2002). "Figure 12: Simplified cross section of FinFET double-gate MOSFET.". In Park, Yoon-Soo; Shur, Michael; Tang, William (eds.). Frontiers in electronics: future chips : proceedings of the 2002 Workshop on Frontiers in Electronics (WOFE-02), St Croix, Virgin Islands, USA, 6–11 January 2002. World Scientific. p. 82. ISBN 978-981-238-222-1.
  242. ^ Lee, J.-H.; Lee, J.-W.; Jung, H.-A.-R.; Choi, B.-K. (2009). "Comparison of SOI FinFETs and bulk FinFETs: Figure 2". Silicon-on-Insulator Technology and Devices. The Electrochemical Society. p. 102. ISBN 978-1-56677-712-4.
  243. ^ Colinge, J.P. (2008). FinFETs and Other Multi-Gate Transistors. Springer Science & Business Media. p. 11. ISBN 9780387717517.
  244. ^ Sekigawa, Toshihiro; Hayashi, Yutaka (1 August 1984). "Calculated threshold-voltage characteristics of an XMOS transistor having an additional bottom gate". Solid-State Electronics. 27 (8): 827–828. Bibcode:1984SSEle..27..827S. doi:10.1016/0038-1101(84)90036-4. ISSN 0038-1101.
  245. ^ Masuoka, Fujio; Takato, H.; Sunouchi, K.; Okabe, N.; Nitayama, A.; Hieda, K.; Horiguchi, F. (December 1988). "High performance CMOS surrounding-gate transistor (SGT) for ultra high density LSIs". Technical Digest., International Electron Devices Meeting: 222–225. doi:10.1109/IEDM.1988.32796.
  246. ^ Brozek, Tomasz (2017). Micro- and Nanoelectronics: Emerging Device Challenges and Solutions. CRC Press. p. 117. ISBN 9781351831345.
  247. ^ "IEEE Andrew S. Grove Award Recipients". IEEE Andrew S. Grove Award. Institute of Electrical and Electronics Engineers. Retrieved 4 July 2019.
  248. ^ "The Breakthrough Advantage for FPGAs with Tri-Gate Technology" (PDF). Intel. 2014. Retrieved 4 July 2019.
  249. ^ Lojek, Bo (2007). History of Semiconductor Engineering. Springer Science & Business Media. pp. 120 & 321-323. ISBN 9783540342588.
  250. ^ Bassett, Ross Knox (2007). To the Digital Age: Research Labs, Start-up Companies, and the Rise of MOS Technology. Johns Hopkins University Press. p. 46. ISBN 9780801886393.
  251. ^ "Computer History Museum – The Silicon Engine | 1955 – Photolithography Techniques Are Used to Make Silicon Devices". Computerhistory.org. Retrieved 2012-06-02.
  252. ^ "1964 – First Commercial MOS IC Introduced". Computer History Museum.
  253. ^ Kilby, J. S. (2007). "Miniaturized electronic circuits [US Patent No. 3,138, 743]". IEEE Solid-State Circuits Society Newsletter. 12 (2): 44–54. doi:10.1109/N-SSC.2007.4785580. ISSN 1098-4232.
  254. ^ "1968: Silicon Gate Technology Developed for ICs". Computer History Museum. Retrieved 22 July 2019.
  255. ^ a b Nigel Tout. "Sharp QT-8D "micro Compet"". Vintage Calculators Web Museum. Retrieved September 29, 2010.
  256. ^ a b c "Hand-held Calculators". Vintage Calculators Web Museum. Retrieved 22 July 2019.
  257. ^ Schwarz, A. F. (2014). Handbook of VLSI Chip Design and Expert Systems. Academic Press. p. 16. ISBN 9781483258058.
  258. ^ "1971: Microprocessor Integrates CPU Function onto a Single Chip". The Silicon Engine. Computer History Museum. Retrieved 22 July 2019.
  259. ^ Cushman, Robert H. (20 September 1975). "2-1/2-generation μP's-$10 parts that perform like low-end mini's" (PDF). EDN.
  260. ^ "Computer History Museum – Exhibits – Microprocessors". Computerhistory.org. Retrieved 2012-06-02.
  261. ^ Grant, Duncan Andrew; Gowar, John (1989). Power MOSFETS: theory and applications. Wiley. p. 239. ISBN 9780471828679.
  262. ^ Carbone, James (September–October 2018). "Buyers can expect 30-week lead times and higher tags to continue for MOSFETs" (PDF). Electronics Sourcing: 18–19.
  263. ^ a b "DRAM". IBM100. IBM. 9 August 2017. Retrieved 20 September 2019.
  264. ^ "1970: MOS Dynamic RAM Competes with Magnetic Core Memory on Price". Computer History Museum. Retrieved 29 July 2019.
  265. ^ "People". The Silicon Engine. Computer History Museum. Retrieved 17 August 2019.
  266. ^ Nathanson HC, Wickstrom RA (1965). "A Resonant-Gate Silicon Surface Transistor with High-Q Band-Pass Properties". Appl. Phys. Lett. 7 (4): 84–86. Bibcode:1965ApPhL...7...84N. doi:10.1063/1.1754323.
  267. ^ Boyle, William S; Smith, George E. (1970). "Charge Coupled Semiconductor Devices". Bell Syst. Tech. J. 49 (4): 587–593. doi:10.1002/j.1538-7305.1970.tb01790.x.
  268. ^ Matsumoto, Kazuya; et al. (1985). "A new MOS phototransistor operating in a non-destructive readout mode". Japanese Journal of Applied Physics. 24 (5A): L323. Bibcode:1985JaJAP..24L.323M. doi:10.1143/JJAP.24.L323.
  269. ^ Eric R. Fossum (1993), "Active Pixel Sensors: Are CCD's Dinosaurs?" Proc. SPIE Vol. 1900, p. 2–14, Charge-Coupled Devices and Solid State Optical Sensors III, Morley M. Blouke; Ed.
  270. ^ Brain, Marshall; Carmack, Carmen (24 April 2000). "How Computer Mice Work". HowStuffWorks. Retrieved 9 October 2019.
  271. ^ Jun-ichi Wakabayashi; Shinji Kawaji (1978). "Hall effect in silicon MOS inversion layers under strong magnetic fields". J. Phys. Soc. Jpn. 44 (6): 1839. Bibcode:1978JPSJ...44.1839W. doi:10.1143/JPSJ.44.1839.
  272. ^ "ReVera's FinFET Control". revera.com. Archived from the original on 19 September 2010.
  273. ^ Colinge, Jean-Pierre; Colinge, Cynthia A. (2002). Physics of Semiconductor Devices. Dordrecht: Springer. p. 233, Figure 7.46. ISBN 978-1-4020-7018-1.
  274. ^ Weber, Eicke R.; Dabrowski, Jarek, eds. (2004). Predictive Simulation of Semiconductor Processing: Status and Challenges. Dordrecht: Springer. p. 5, Figure 1.2. ISBN 978-3-540-20481-7.
  275. ^ "International Technology Roadmap for Semiconductors". Archived from the original on 2015-12-28.
  276. ^ Shilov, Anton. "Samsung Completes Development of 5nm EUV Process Technology". www.anandtech.com. Retrieved 2019-05-31.
  277. ^ Shilov, Anton. "TSMC: First 7nm EUV Chips Taped Out, 5nm Risk Production in Q2 2019".
  278. ^ "1965 – "Moore's Law" Predicts the Future of Integrated Circuits". Computer History Museum.
  279. ^ Roy, Kaushik; Yeo, Kiat Seng (2004). Low Voltage, Low Power VLSI Subsystems. McGraw-Hill Professional. Fig. 2.1, p. 44, Fig. 1.1, p. 4. ISBN 978-0-07-143786-8.
  280. ^ Vasileska, Dragica; Goodnick, Stephen (2006). Computational Electronics. Morgan & Claypool. p. 103. ISBN 978-1-59829-056-1.
  281. ^ "Frontier Semiconductor Paper" (PDF). Archived from the original (PDF) on February 27, 2012. Retrieved 2012-06-02.
  282. ^ Chen, Wai-Kai (2006). The VLSI Handbook. CRC Press. Fig. 2.28, p. 2–22. ISBN 978-0-8493-4199-1.
  283. ^ Lindsay, R.; Pawlak; Kittl; Henson; Torregiani; Giangrandi; Surdeanu; Vandervorst; Mayur; Ross; McCoy; Gelpey; Elliott; Pages; Satta; Lauwers; Stolk; Maex (2011). "A Comparison of Spike, Flash, SPER and Laser Annealing for 45nm CMOS". MRS Proceedings. 765. doi:10.1557/PROC-765-D7.4.
  284. ^ "VLSI wiring capacitance" (PDF). IBM Journal of Research and Development.[dead link]
  285. ^ Soudris, D.; Pirsch, P.; Barke, E., eds. (2000). Integrated Circuit Design: Power and Timing Modeling, Optimization, and Simulation (10th Int. Workshop). Springer. p. 38. ISBN 978-3-540-41068-3.
  286. ^ Orshansky, Michael; Nassif, Sani; Boning, Duane (2007). Design for Manufacturability And Statistical Design: A Constructive Approach. New York 309284: Springer. ISBN 9780387309286.
  287. ^ Cherry, Steven (2004). "Edholm's law of bandwidth". IEEE Spectrum. 41 (7): 58–60. doi:10.1109/MSPEC.2004.1309810.
  288. ^ a b c "Angstrom". Collins English Dictionary. Retrieved 2019-03-02.
  289. ^ Sze, Simon M. (2002). Semiconductor Devices: Physics and Technology (PDF) (2nd ed.). Wiley. p. 4. ISBN 0-471-33372-7.
  290. ^ Atalla, Mohamed M.; Kahng, Dawon (June 1960). "Silicon–silicon dioxide field induced surface devices". IRE-AIEE Solid State Device Research Conference. Carnegie Mellon University Press.
  291. ^ Voinigescu, Sorin (2013). High-Frequency Integrated Circuits. Cambridge University Press. p. 164. ISBN 9780521873024.
  292. ^ Sah, Chih-Tang; Leistiko, Otto; Grove, A. S. (May 1965). "Electron and hole mobilities in inversion layers on thermally oxidized silicon surfaces". IEEE Transactions on Electron Devices. 12 (5): 248–254. doi:10.1109/T-ED.1965.15489.
  293. ^ Dennard, Robert H.; Gaensslen, Fritz H.; Yu, Hwa-Nien; Kuhn, L. (December 1972). "Design of micron MOS switching devices". 1972 International Electron Devices Meeting: 168–170. doi:10.1109/IEDM.1972.249198.
  294. ^ a b Hori, Ryoichi; Masuda, Hiroo; Minato, Osamu; Nishimatsu, Shigeru; Sato, Kikuji; Kubo, Masaharu (September 1975). "Short Channel MOS-IC Based on Accurate Two Dimensional Device Design". Japanese Journal of Applied Physics. 15 (S1): 193. doi:10.7567/JJAPS.15S1.193. ISSN 1347-4065.
  295. ^ Critchlow, D. L. (2007). "Recollections on MOSFET Scaling". IEEE Solid-State Circuits Society Newsletter. 12 (1): 19–22. doi:10.1109/N-SSC.2007.4785536.
  296. ^ "1970s: Development and evolution of microprocessors" (PDF). Semiconductor History Museum of Japan. Retrieved 27 June 2019.
  297. ^ "NEC 751 (uCOM-4)". The Antique Chip Collector's Page. Archived from the original on 2011-05-25. Retrieved 2010-06-11.
  298. ^ "1973: 12-bit engine-control microprocessor (Toshiba)" (PDF). Semiconductor History Museum of Japan. Retrieved 27 June 2019.
  299. ^ Belzer, Jack; Holzman, Albert G.; Kent, Allen (1978). Encyclopedia of Computer Science and Technology: Volume 10 - Linear and Matrix Algebra to Microorganisms: Computer-Assisted Identification. CRC Press. p. 402. ISBN 9780824722609.
  300. ^ Dennard, Robert H.; Gaensslen, F. H.; Yu, Hwa-Nien; Rideout, V. L.; Bassous, E.; LeBlanc, A. R. (October 1974). "Design of ion-implanted MOSFET's with very small physical dimensions" (PDF). IEEE Journal of Solid-State Circuits. 9 (5): 256–268. doi:10.1109/JSSC.1974.1050511.
  301. ^ Kubo, Masaharu; Hori, Ryoichi; Minato, Osamu; Sato, Kikuji (February 1976). "A threshold voltage controlling circuit for short channel MOS integrated circuits". 1976 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. XIX: 54–55. doi:10.1109/ISSCC.1976.1155515.
  302. ^ "Intel Microprocessor Quick Reference Guide". Intel. Retrieved 27 June 2019.
  303. ^ Hunter, William R.; Ephrath, L. M.; Cramer, Alice; Grobman, W. D.; Osburn, C. M.; Crowder, B. L.; Luhn, H. E. (April 1979). "1 /spl mu/m MOSFET VLSI technology. V. A single-level polysilicon technology using electron-beam lithography". IEEE Journal of Solid-State Circuits. 14 (2): 275–281. doi:10.1109/JSSC.1979.1051174.
  304. ^ Kobayashi, Toshio; Horiguchi, Seiji; Kiuchi, K. (December 1984). "Deep-submicron MOSFET characteristics with 5 nm gate oxide". 1984 International Electron Devices Meeting: 414–417. doi:10.1109/IEDM.1984.190738.
  305. ^ Kobayashi, Toshio; Horiguchi, Seiji; Miyake, M.; Oda, M.; Kiuchi, K. (December 1985). "Extremely high transconductance (above 500 mS/mm) MOSFET with 2.5 nm gate oxide". 1985 International Electron Devices Meeting: 761–763. doi:10.1109/IEDM.1985.191088.
  306. ^ Chou, Stephen Y.; Antoniadis, Dimitri A.; Smith, Henry I. (December 1985). "Observation of electron velocity overshoot in sub-100-nm-channel MOSFET's in Silicon". IEEE Electron Device Letters. 6 (12): 665–667. doi:10.1109/EDL.1985.26267.
  307. ^ a b Chou, Stephen Y.; Smith, Henry I.; Antoniadis, Dimitri A. (January 1986). "Sub‐100‐nm channel‐length transistors fabricated using x‐ray lithography". Journal of Vacuum Science & Technology B: Microelectronics Processing and Phenomena. 4 (1): 253–255. doi:10.1116/1.583451. ISSN 0734-211X.
  308. ^ Kobayashi, Toshio; Miyake, M.; Deguchi, K.; Kimizuka, M.; Horiguchi, Seiji; Kiuchi, K. (1987). "Subhalf-micrometer p-channel MOSFET's with 3.5-nm gate Oxide fabricated using X-ray lithography". IEEE Electron Device Letters. 8 (6): 266–268. doi:10.1109/EDL.1987.26625.
  309. ^ Ono, Mizuki; Saito, Masanobu; Yoshitomi, Takashi; Fiegna, Claudio; Ohguro, Tatsuya; Iwai, Hiroshi (December 1993). "Sub-50 nm gate length n-MOSFETs with 10 nm phosphorus source and drain junctions". Proceedings of IEEE International Electron Devices Meeting: 119–122. doi:10.1109/IEDM.1993.347385.
  310. ^ Kawaura, Hisao; Sakamoto, Toshitsugu; Baba, Toshio; Ochiai, Yukinori; Fujita, Jun'ichi; Matsui, Shinji; Sone, Jun'ichi (1997). "Proposal of Pseudo Source and Drain MOSFETs for Evaluating 10-nm Gate MOSFETs". Japanese Journal of Applied Physics. 36 (3S): 1569. doi:10.1143/JJAP.36.1569. ISSN 1347-4065.
  311. ^ Ahmed, Khaled Z.; Ibok, Effiong E.; Song, Miryeong; Yeap, Geoffrey; Xiang, Qi; Bang, David S.; Lin, Ming-Ren (1998). "Performance and reliability of sub-100 nm MOSFETs with ultra thin direct tunneling gate oxides". 1998 Symposium on VLSI Technology Digest of Technical Papers (Cat. No.98CH36216): 160–161. doi:10.1109/VLSIT.1998.689240.
  312. ^ Ahmed, Khaled Z.; Ibok, Effiong E.; Song, Miryeong; Yeap, Geoffrey; Xiang, Qi; Bang, David S.; Lin, Ming-Ren (1998). "Sub-100 nm nMOSFETs with direct tunneling thermal, nitrous and nitric oxides". 56th Annual Device Research Conference Digest (Cat. No.98TH8373): 10–11. doi:10.1109/DRC.1998.731099.
  313. ^ Doris, Bruce B.; Dokumaci, Omer H.; Ieong, Meikei K.; Mocuta, Anda; Zhang, Ying; Kanarsky, Thomas S.; Roy, R. A. (December 2002). "Extreme scaling with ultra-thin Si channel MOSFETs". Digest. International Electron Devices Meeting: 267–270. doi:10.1109/IEDM.2002.1175829.
  314. ^ a b c Schwierz, Frank; Wong, Hei; Liou, Juin J. (2010). Nanometer CMOS. Pan Stanford Publishing. p. 17. ISBN 9789814241083.
  315. ^ "IBM claims world's smallest silicon transistor - TheINQUIRER". Theinquirer.net. 2002-12-09. Retrieved 7 December 2017.
  316. ^ a b Wakabayashi, Hitoshi; Yamagami, Shigeharu; Ikezawa, Nobuyuki; Ogura, Atsushi; Narihiro, Mitsuru; Arai, K.; Ochiai, Y.; Takeuchi, K.; Yamamoto, T.; Mogami, T. (December 2003). "Sub-10-nm planar-bulk-CMOS devices using lateral junction control". IEEE International Electron Devices Meeting 2003: 20.7.1–20.7.3. doi:10.1109/IEDM.2003.1269446.
  317. ^ Sah, Chih-Tang; Wanlass, Frank (February 1963). "Nanowatt logic using field-effect metal–oxide semiconductor triodes". 1963 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. VI: 32–33. doi:10.1109/ISSCC.1963.1157450.
  318. ^ a b Lojek, Bo (2007). History of Semiconductor Engineering. Springer Science & Business Media. p. 330. ISBN 9783540342588.
  319. ^ Aitken, A.; Poulsen, R. G.; MacArthur, A. T. P.; White, J. J. (December 1976). "A fully plasma etched-ion implanted CMOS process". 1976 International Electron Devices Meeting: 209–213. doi:10.1109/IEDM.1976.189021.
  320. ^ Masuhara, Toshiaki; Minato, Osamu; Sasaki, Toshio; Sakai, Yoshio; Kubo, Masaharu; Yasui, Tokumasa (February 1978). "A high-speed, low-power Hi-CMOS 4K static RAM". 1978 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. XXI: 110–111. doi:10.1109/ISSCC.1978.1155749.
  321. ^ Masuhara, Toshiaki; Minato, Osamu; Sakai, Yoshi; Sasaki, Toshio; Kubo, Masaharu; Yasui, Tokumasa (September 1978). "Short Channel Hi-CMOS Device and Circuits". ESSCIRC 78: 4th European Solid State Circuits Conference - Digest of Technical Papers: 131–132.
  322. ^ a b c d e Gealow, Jeffrey Carl (10 August 1990). "Impact of Processing Technology on DRAM Sense Amplifier Design" (PDF). CORE. Massachusetts Institute of Technology. pp. 149–166. Retrieved 25 June 2019.
  323. ^ Chwang, R. J. C.; Choi, M.; Creek, D.; Stern, S.; Pelley, P. H.; Schutz, Joseph D.; Bohr, M. T.; Warkentin, P. A.; Yu, K. (February 1983). "A 70ns high density CMOS DRAM". 1983 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. XXVI: 56–57. doi:10.1109/ISSCC.1983.1156456.
  324. ^ Mano, Tsuneo; Yamada, J.; Inoue, Junichi; Nakajima, S. (February 1983). "Submicron VLSI memory circuits". 1983 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. XXVI: 234–235. doi:10.1109/ISSCC.1983.1156549.
  325. ^ Hu, G. J.; Taur, Yuan; Dennard, Robert H.; Terman, L. M.; Ting, Chung-Yu (December 1983). "A self-aligned 1-μm CMOS technology for VLSI". 1983 International Electron Devices Meeting: 739–741. doi:10.1109/IEDM.1983.190615.
  326. ^ Sumi, T.; Taniguchi, Tsuneo; Kishimoto, Mikio; Hirano, Hiroshige; Kuriyama, H.; Nishimoto, T.; Oishi, H.; Tetakawa, S. (1987). "A 60ns 4Mb DRAM in a 300mil DIP". 1987 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. XXX: 282–283. doi:10.1109/ISSCC.1987.1157106.
  327. ^ Mano, Tsuneo; Yamada, J.; Inoue, Junichi; Nakajima, S.; Matsumura, Toshiro; Minegishi, K.; Miura, K.; Matsuda, T.; Hashimoto, C.; Namatsu, H. (1987). "Circuit technologies for 16Mb DRAMs". 1987 IEEE International Solid-State Circuits Conference. Digest of Technical Papers. XXX: 22–23. doi:10.1109/ISSCC.1987.1157158.
  328. ^ Hanafi, Hussein I.; Dennard, Robert H.; Taur, Yuan; Haddad, Nadim F.; Sun, J. Y. C.; Rodriguez, M. D. (September 1987). "0.5 μm CMOS Device Design and Characterization". ESSDERC '87: 17th European Solid State Device Research Conference: 91–94.
  329. ^ Kasai, Naoki; Endo, Nobuhiro; Kitajima, Hiroshi (December 1987). "0.25 μm CMOS technology using P+polysilicon gate PMOSFET". 1987 International Electron Devices Meeting: 367–370. doi:10.1109/IEDM.1987.191433.
  330. ^ Inoue, M.; Kotani, H.; Yamada, T.; Yamauchi, Hiroyuki; Fujiwara, A.; Matsushima, J.; Akamatsu, Hironori; Fukumoto, M.; Kubota, M.; Nakao, I.; Aoi (1988). "A 16mb Dram with an Open Bit-Line Architecture". 1988 IEEE International Solid-State Circuits Conference, 1988 ISSCC. Digest of Technical Papers: 246–. doi:10.1109/ISSCC.1988.663712.
  331. ^ Shahidi, Ghavam G.; Davari, Bijan; Taur, Yuan; Warnock, James D.; Wordeman, Matthew R.; McFarland, P. A.; Mader, S. R.; Rodriguez, M. D. (December 1990). "Fabrication of CMOS on ultrathin SOI obtained by epitaxial lateral overgrowth and chemical-mechanical polishing". International Technical Digest on Electron Devices: 587–590. doi:10.1109/IEDM.1990.237130.
  332. ^ "Memory". STOL (Semiconductor Technology Online). Retrieved 25 June 2019.
  333. ^ "0.18-micron Technology". TSMC. Retrieved 30 June 2019.
  334. ^ "NEC test-produces world's smallest transistor". Thefreelibrary.com. Retrieved 7 December 2017.
  335. ^ Sekigawa, Toshihiro; Hayashi, Yutaka (August 1984). "Calculated threshold-voltage characteristics of an XMOS transistor having an additional bottom gate". Solid-State Electronics. 27 (8): 827–828. doi:10.1016/0038-1101(84)90036-4. ISSN 0038-1101.
  336. ^ Koike, Hanpei; Nakagawa, Tadashi; Sekigawa, Toshiro; Suzuki, E.; Tsutsumi, Toshiyuki (23 February 2003). "Primary Consideration on Compact Modeling of DG MOSFETs with Four-terminal Operation Mode" (PDF). TechConnect Briefs. 2 (2003): 330–333.
  337. ^ Davari, Bijan; Chang, Wen-Hsing; Wordeman, Matthew R.; Oh, C. S.; Taur, Yuan; Petrillo, Karen E.; Rodriguez, M. D. (December 1988). "A high performance 0.25 mu m CMOS technology". Technical Digest., International Electron Devices Meeting: 56–59. doi:10.1109/IEDM.1988.32749.
  338. ^ Davari, Bijan; Wong, C. Y.; Sun, Jack Yuan-Chen; Taur, Yuan (December 1988). "Doping of n/sup +/ and p/sup +/ polysilicon in a dual-gate CMOS process". Technical Digest., International Electron Devices Meeting: 238–241. doi:10.1109/IEDM.1988.32800.
  339. ^ Masuoka, Fujio; Takato, Hiroshi; Sunouchi, Kazumasa; Okabe, N.; Nitayama, Akihiro; Hieda, K.; Horiguchi, Fumio (December 1988). "High performance CMOS surrounding-gate transistor (SGT) for ultra high density LSIs". Technical Digest., International Electron Devices Meeting: 222–225. doi:10.1109/IEDM.1988.32796.
  340. ^ Brozek, Tomasz (2017). Micro- and Nanoelectronics: Emerging Device Challenges and Solutions. CRC Press. p. 117. ISBN 9781351831345.
  341. ^ Ishikawa, Fumitaro; Buyanova, Irina (2017). Novel Compound Semiconductor Nanowires: Materials, Devices, and Applications. CRC Press. p. 457. ISBN 9781315340722.
  342. ^ Colinge, J.P. (2008). FinFETs and Other Multi-Gate Transistors. Springer Science & Business Media. p. 11. ISBN 9780387717517.
  343. ^ Hisamoto, Digh; Kaga, Toru; Kawamoto, Yoshifumi; Takeda, Eiji (December 1989). "A fully depleted lean-channel transistor (DELTA)-a novel vertical ultra thin SOI MOSFET". International Technical Digest on Electron Devices Meeting: 833–836. doi:10.1109/IEDM.1989.74182.
  344. ^ "IEEE Andrew S. Grove Award Recipients". IEEE Andrew S. Grove Award. Institute of Electrical and Electronics Engineers. Retrieved 4 July 2019.
  345. ^ Hisamoto, Digh; Hu, Chenming; Liu, Tsu-Jae King; Bokor, Jeffrey; Lee, Wen-Chin; Kedzierski, Jakub; Anderson, Erik; Takeuchi, Hideki; Asano, Kazuya (December 1998). "A folded-channel MOSFET for deep-sub-tenth micron era". International Electron Devices Meeting 1998. Technical Digest (Cat. No.98CH36217): 1032–1034. doi:10.1109/IEDM.1998.746531.
  346. ^ Hu, Chenming; Choi, Yang‐Kyu; Lindert, N.; Xuan, P.; Tang, S.; Ha, D.; Anderson, E.; Bokor, J.; Tsu-Jae King, Liu (December 2001). "Sub-20 nm CMOS FinFET technologies". International Electron Devices Meeting. Technical Digest (Cat. No.01CH37224): 19.1.1–19.1.4. doi:10.1109/IEDM.2001.979526.
  347. ^ Ahmed, Shibly; Bell, Scott; Tabery, Cyrus; Bokor, Jeffrey; Kyser, David; Hu, Chenming; Liu, Tsu-Jae King; Yu, Bin; Chang, Leland (December 2002). "FinFET scaling to 10 nm gate length" (PDF). Digest. International Electron Devices Meeting: 251–254. doi:10.1109/IEDM.2002.1175825.
  348. ^ Lee, Hyunjin; Choi, Yang-Kyu; Yu, Lee-Eun; Ryu, Seong-Wan; Han, Jin-Woo; Jeon, K.; Jang, D.Y.; Kim, Kuk-Hwan; Lee, Ju-Hyun; et al. (June 2006), "Sub-5nm All-Around Gate FinFET for Ultimate Scaling", Symposium on VLSI Technology, 2006: 58–59, doi:10.1109/VLSIT.2006.1705215, hdl:10203/698, ISBN 978-1-4244-0005-8
  349. ^ "Still Room at the Bottom (nanometer transistor developed by Yang-kyu Choi from the Korea Advanced Institute of Science and Technology )", Nanoparticle News, 1 April 2006, archived from the original on 6 November 2012
  350. ^ Weimer, Paul K. (June 1962). "The TFT A New Thin-Film Transistor". Proceedings of the IRE. 50 (6): 1462–1469. doi:10.1109/JRPROC.1962.288190. ISSN 0096-8390.
  351. ^ Brody, T. P.; Kunig, H. E. (October 1966). "A HIGH‐GAIN InAs THIN‐FILM TRANSISTOR". Applied Physics Letters. 9 (7): 259–260. doi:10.1063/1.1754740. ISSN 0003-6951.
  352. ^ Woodall, Jerry M. (2010). Fundamentals of III-V Semiconductor MOSFETs. Springer Science & Business Media. pp. 2–3. ISBN 9781441915474.
  353. ^ Kahng, Dawon; Sze, Simon Min (July–August 1967). "A floating gate and its application to memory devices". The Bell System Technical Journal. 46 (6): 1288–1295. doi:10.1002/j.1538-7305.1967.tb01738.x.
  354. ^ Wegener, H. A. R.; Lincoln, A. J.; Pao, H. C.; O'Connell, M. R.; Oleksiak, R. E.; Lawrence, H. (October 1967). "The variable threshold transistor, a new electrically-alterable, non-destructive read-only storage device". 1967 International Electron Devices Meeting. 13: 70. doi:10.1109/IEDM.1967.187833.
  355. ^ Lin, Hung Chang; Iyer, Ramachandra R. (July 1968). "A Monolithic Mos-Bipolar Audio Amplifier". IEEE Transactions on Broadcast and Television Receivers. 14 (2): 80–86. doi:10.1109/TBTR1.1968.4320132.
  356. ^ a b Alvarez, Antonio R. (1990). "Introduction To BiCMOS". BiCMOS Technology and Applications. Springer Science & Business Media. pp. 1–20 (2). doi:10.1007/978-1-4757-2029-7_1. ISBN 9780792393849.
  357. ^ Lin, Hung Chang; Iyer, Ramachandra R.; Ho, C. T. (October 1968). "Complementary MOS-bipolar structure". 1968 International Electron Devices Meeting: 22–24. doi:10.1109/IEDM.1968.187949.
  358. ^ a b "Advances in Discrete Semiconductors March On". Power Electronics Technology. Informa: 52–6. September 2005. Archived (PDF) from the original on 22 March 2006. Retrieved 31 July 2019.
  359. ^ Oxner, E. S. (1988). Fet Technology and Application. CRC Press. p. 18. ISBN 9780824780500.
  360. ^ Tarui, Y.; Hayashi, Y.; Sekigawa, Toshihiro (September 1969). "Diffusion Self-Aligned MOST; A New Approach for High Speed Device". Proceedings of the 1st Conference on Solid State Devices. doi:10.7567/SSDM.1969.4-1.
  361. ^ McLintock, G. A.; Thomas, R. E. (December 1972). "Modelling of the double-diffused MOST's with self-aligned gates". 1972 International Electron Devices Meeting: 24–26. doi:10.1109/IEDM.1972.249241.
  362. ^ Bergveld, P. (January 1970). "Development of an Ion-Sensitive Solid-State Device for Neurophysiological Measurements". IEEE Transactions on Biomedical Engineering. BME-17 (1): 70–71. doi:10.1109/TBME.1970.4502688.
  363. ^ Chris Toumazou; Pantelis Georgiou (December 2011). "40 years of ISFET technology: From neuronal sensing to DNA sequencing". Electronics Letters. doi:10.1049/el.2011.3231. Retrieved 13 May 2016.
  364. ^ Tarui, Y.; Hayashi, Y.; Sekigawa, Toshihiro (October 1970). "DSA enhancement - Depletion MOS IC". 1970 International Electron Devices Meeting: 110–110. doi:10.1109/IEDM.1970.188299.
  365. ^ Baliga, B. Jayant (2015). The IGBT Device: Physics, Design and Applications of the Insulated Gate Bipolar Transistor. William Andrew. pp. xxviii, 5–12. ISBN 9781455731534.
  366. ^ Higuchi, H.; Kitsukawa, Goro; Ikeda, Takahide; Nishio, Y.; Sasaki, N.; Ogiue, Katsumi (December 1984). "Performance and structures of scaled-down bipolar devices merged with CMOSFETs". 1984 International Electron Devices Meeting: 694–697. doi:10.1109/IEDM.1984.190818.
  367. ^ Deguchi, K.; Komatsu, Kazuhiko; Miyake, M.; Namatsu, H.; Sekimoto, M.; Hirata, K. (1985). "Step-and-Repeat X-ray/Photo Hybrid Lithography for 0.3 μm Mos Devices". 1985 Symposium on VLSI Technology. Digest of Technical Papers: 74–75.
  368. ^ Momose, H.; Shibata, Hideki; Saitoh, S.; Miyamoto, Jun-ichi; Kanzaki, K.; Kohyama, Susumu (1985). "1.0-/spl mu/m n-Well CMOS/Bipolar Technology". IEEE Journal of Solid-State Circuits. 20 (1): 137–143. doi:10.1109/JSSC.1985.1052286.
  369. ^ Lee, Han-Sheng; Puzio, L.C. (November 1986). "The electrical properties of subquarter-micrometer gate-length MOSFET's". IEEE Electron Device Letters. 7 (11): 612–614. doi:10.1109/EDL.1986.26492.
  370. ^ Shahidi, Ghavam G.; Antoniadis, Dimitri A.; Smith, Henry I. (December 1986). "Electron velocity overshoot at 300 K and 77 K in silicon MOSFETs with submicron channel lengths". 1986 International Electron Devices Meeting: 824–825. doi:10.1109/IEDM.1986.191325.
  371. ^ Davari, Bijan; Ting, Chung-Yu; Ahn, Kie Y.; Basavaiah, S.; Hu, Chao-Kun; Taur, Yuan; Wordeman, Matthew R.; Aboelfotoh, O. (May 1987). "Submicron Tungsten Gate MOSFET with 10 nm Gate Oxide". 1987 Symposium on VLSI Technology. Digest of Technical Papers: 61–62.
  372. ^ Havemann, Robert H.; Eklund, R. E.; Tran, Hiep V.; Haken, R. A.; Scott, D. B.; Fung, P. K.; Ham, T. E.; Favreau, D. P.; Virkus, R. L. (December 1987). "An 0.8 #181;m 256K BiCMOS SRAM technology". 1987 International Electron Devices Meeting: 841–843. doi:10.1109/IEDM.1987.191564.
  373. ^ Kawaura, Hisao; Sakamoto, Toshitsugu; Baba, Toshio; Ochiai, Yukinori; Fujita, Jun-ichi; Matsui, Shinji; Sone, J. (1997). "Transistor operations in 30-nm-gate-length EJ-MOSFETs". 1997 55th Annual Device Research Conference Digest: 14–15. doi:10.1109/DRC.1997.612456.
  374. ^ Kawaura, Hisao; Sakamoto, Toshitsugu; Baba, Toshio (12 June 2000). "Observation of source-to-drain direct tunneling current in 8 nm gate electrically variable shallow junction metal–oxide–semiconductor field-effect transistors". Applied Physics Letters. 76 (25): 3810–3812. doi:10.1063/1.126789. ISSN 0003-6951.

External links[edit]