Metalorganic vapour phase epitaxy
Metalorganic vapour phase epitaxy (MOVPE), also known as organometallic vapour phase epitaxy (OMVPE) or metalorganic chemical vapour deposition (MOCVD), is a chemical vapour deposition method used to produce single or polycrystalline thin films. It is a highly complex process for growing crystalline layers to create complex semiconductor multilayer structures. In contrast to molecular beam epitaxy (MBE) the growth of crystals is by chemical reaction and not physical deposition. This takes place not in a vacuum, but from the gas phase at moderate pressures (10 to 760 Torr). As such, this technique is preferred for the formation of devices incorporating thermodynamically metastable alloys, and it has become a major process in the manufacture of optoelectronics.
In MOCVD ultra pure gases are injected into a reactor and finely dosed to deposit a very thin layer of atoms onto a semiconductor wafer. Surface reaction of organic compounds or metalorganics and hydrides containing the required chemical elements creates conditions for crystalline growth - epitaxy of materials and compound semiconductors. Unlike traditional silicon semiconductors, these semiconductors may contain combinations of Group III and Group V, Group II and Group VI, Group IV, or Group IV, V and VI elements.
For example, indium phosphide could be grown in a reactor on a heated substrate by introducing trimethylindium ((CH3)3In) and phosphine (PH3) in a first step. The heated organic precursor molecules decompose in the absence of oxygen - pyrolysis. Pyrolysis leaves the atoms on the substrate surface in the second step. The atoms bond to the substrate surface and a new crystalline layer is grown in the last step. Formation of this epitaxial layer occurs at the substrate surface.
Required pyrolysis temperature increases with increasing chemical bond strength of the precursor. The more carbon atoms are attached to the central metal atom the weaker the bond. The diffusion of atoms on the substrate surface is affected by atomic steps on the surface.
In the metal organic chemical vapor deposition (MOCVD) technique, reactant gases are combined at elevated temperatures in the reactor to cause a chemical interaction, resulting in the deposition of materials on the substrate.
A reactor is a chamber made of a material that does not react with the chemicals being used. It must also withstand high temperatures. This chamber is composed by reactor walls, liner, a susceptor, gas injection units, and temperature control units. Usually, the reactor walls are made from stainless steel or quartz. Ceramic or special glasses, such as quartz, are often used as the liner in the reactor chamber between the reactor wall and the susceptor. To prevent overheating, cooling water must be flowing through the channels within the reactor walls. A substrate sits on a susceptor which is at a controlled temperature. The susceptor is made from a material resistant to the metalorganic compounds used; graphite is sometimes used. For growing nitrides and related materials, a special coating on the graphite susceptor is necessary to prevent corrosion by ammonia (NH3) gas.
One type of reactor used to carry out MOCVD is a cold-wall reactor. In a cold-wall reactor, the substrate is supported by a pedestal, which also acts as a susceptor. The pedestal/susceptor is the primary origin of heat energy in the reaction chamber. Only the susceptor is heated, so gases do not react before they reach the hot wafer surface. The pedestal/susceptor is made of a radiation-absorbing material such as carbon. In contrast, the walls of the reaction chamber in a cold-wall reactor are typically made of quartz which is largely transparent to the electromagnetic radiation. The reaction chamber walls in a cold-wall reactor, however, may be indirectly heated by heat radiating from the hot pedestal/susceptor, but will remain cooler than the pedestal/susceptor and the substrate the pedestal/susceptor supports.
In hot-wall CVD, the entire chamber is heated. This may be necessary for some gases to be pre-cracked before reaching the wafer surface to allow them to stick to the wafer.
Gas inlet and switching system. Gas is introduced via devices known as 'bubblers'. In a bubbler a carrier gas (usually hydrogen in arsenide & phosphide growth or nitrogen for nitride growth) is bubbled through the metalorganic liquid, which picks up some metalorganic vapour and transports it to the reactor. The amount of metalorganic vapour transported depends on the rate of carrier gas flow and the bubbler temperature, and is usually controlled automatically and most accurately by using an ultrasonic concentration measuring feedback gas control system. Allowance must be made for saturated vapors.
Pressure maintenance system
Gas exhaust and cleaning system. Toxic waste products must be converted to liquid or solid wastes for recycling (preferably) or disposal. Ideally processes will be designed to minimize the production of waste products.
- Arsine AsH3, Gas
- Tertiarybutyl arsine (TBAs), Liquid
- Monoethyl arsine (MEAs), Liquid
- Trimethyl arsine (TMAs), Liquid
- Trimethyl antimony (TMSb), Liquid
- Triethyl antimony (TESb), Liquid
- Tri-isopropyl antimony (TIPSb), Liquid
- Stibine SbH3, Gas
- Dimethyl cadmium (DMCd), Liquid
- Diethyl cadmium (DECd), Liquid
- Methyl Allyl Cadmium (MACd), Liquid
- Dimethyl selenide (DMSe), Liquid
- Diethyl selenide (DESe), Liquid
- Di-isopropyl selenide (DIPSe), Liquid
- Di-tert-butyl selenide (DTBSe), Liquid
Semiconductors grown by MOCVD
- Indium arsenic antimonide
Environment, health and safety
As MOCVD has become well-established production technology, there are equally growing concerns associated with its bearing on personnel and community safety, environmental impact and maximum quantities of hazardous materials (such as gases and metalorganics) permissible in the device fabrication operations. The safety as well as responsible environmental care have become major factors of paramount importance in the MOCVD-based crystal growth of compound semiconductors.
- Atomic layer deposition
- Molecular beam epitaxy
- Hydrogen purifier
- Thin-film deposition
- List of semiconductor materials