A circular wing is a disc shaped wing having the outer planform of a circle.
If the aircraft has no fuselage or tail the disc-shaped aircraft is sometimes described as a flying saucer. If the entire disc rotates it is called a disc wing.
Disc-shaped aircraft development dates back to before World War II. A number of disc-shaped aircraft have been proposed over the years, and a few have been built.
Circular wing aircraft
Nemeth Umbrella Plane
In 1934, at Miami University (of Ohio), an aircraft called the Nemeth Umbrella Plane (aka Roundwing) was tested. (Nemeth is sometimes spelled Nuneth.) This aircraft had a parasol wing of circular form above a conventional fuselage and tail, and it was powered by propeller in a tractor configuration.
During World War II, a number of disc-shaped aircraft were proposed by aircraft designers in Nazi Germany. One of the few to make it further than the drawing board was the Sack AS-6, an experimental light plane with a round-winged planform that first flew in 1944. The aircraft proved unsuccessful, and was scrapped in early 1945.
Vought Flying Flapjack
During WWII, Charles Zimmerman led a team at Chance-Vought that created a series of designs that eventually resulted in the Vought Flying Flapjack, one of the first aircraft explicitly designed as a disc for aerodynamic reasons. The Flapjack had a large wing and very low wing loading, allowing it to takeoff easily from aircraft carriers. As with the earlier Vought V-173, the Flapjack's counter-rotating propellers were located at the ends of the wings to help counteract the drag-inducing vortices that would normally result from a wing of such a low aspect ratio. By the time the design was flying in the post-war era, jet engines had rendered the design obsolete and the US Navy lost interest.
In 1943, Boeing Aircraft built 3 scale model aircraft whose designs had saucer-shaped wings with a propeller in the front, and a rudder in the back. The cockpit was to be in front of the wings. There was no actual fuselage in the center. The aircraft model numbers were 390, 391, and 396. They were to be powered by a Pratt & Whitney R-4360-3 Wasp Major radial engine and capable of reaching speeds of 414 mph. They were intended to be fighter planes, armed with 4 20mm cannons and underwing hardpoint that could carry 1,134 kg (2,500 lb) bombs or external fuel tanks. Boeing submitted the proposals to the US Navy. The wing design had excellent short takeoff and landing (STOL) characteristics, that is preferred for fixed-wing aircraft carrier planes. The Navy rejected the Boeing designs in favor of the similar-shaped Chance-Vought V-173/XF5U-1 aircraft.
Circular flying wings (flying saucers)
After the war, the Avro Canada company developed a saucer-shaped aircraft. John Frost became interested in the Coandă effect to produce lift, eventually designing a disc-shape in which the thrust was directed downward around the entire disc by a flap ringing the aircraft, allowing it to takeoff and land vertically. Once in flight, the flap would be angled slightly, producing a small thrust while being directed to the rear. Little lift would be generated by conventional means, the engine thust would instead be used to build an "artificial wing" by directing the airflow around the craft. He offered a number of increasingly dramatic performance estimates, generally claiming Mach 4 performance at 24,000 m (79,000 ft), at which point the USAF took over funding under Weapon System 606A. The result was a 29-feet (8.9 m) diameter supersonic Project Y2.
Testing soon revealed that the entire concept was unworkable; the craft would be highly unstable at supersonic speed. Avro nevertheless continued work on the project as a subsonic design known as Project Silver Bug. Silver Bug was of interest to the US Army, who was looking for solutions for battlefield transport and support, and they took over most of the project funding. The final outcome of Silver Bug was the Avrocar or VZ-9AV, effectively (and unintentionally) a prototype hovercraft rather than an aircraft, which was made public in 1961.
Moller M200G Volantor
The M200G Volantor is a prototype flying saucer-style hovercraft, designed by aeronautics engineer Paul Moller. The M200G Volantor uses a system of eight computer-controlled ducted fans to hover up to 10 feet (3 m) above the ground. Volantor is a term coined by Moller meaning "a vertical takeoff and landing aircraft."
- H. C. Levey and P. E. Wynter; "The Circular Wing and Related Problems", Proceedings of the Royal Society of London. Series A, Mathematical and Physical Sciences, Vol. 268, No. 1334 (Jul. 24, 1962), pp. 390-404.
- Nemeth article
- J.Miranda/P.Mercado: Flugzeug Profile 23 - Deutsche Kreisflügelflugzeuge, Flugzeug Publikations GmbH, Illertissen 1995
- Airpower magazine, July 2002, Volume 32, No. 4 pages 42 through 47.
- Link to article on Boeing 390/391/396 with photograph
- Beveridge, John (2007-08-08). "Flying Jetsons come of age with hover pod". Herald Sun. Retrieved 2007-08-30.
- Potts, J.R.; Disc-wing aerodynamics, University of Manchester, 2005.
- List of disc shaped aircraft patents
- 1955 declassified technical report on Project Y2 for Project Silver Bug
- The Sack AS-6, a circular experimental aircraft from WW2 Germany
- Flying Saucer May Yet Take Flight-- the EKIP
- U.S. News and World Report, April 7, 1950; article on experimental US disc-shaped aircraft that can hover like a helicopter and speed up like a jet.
- My Weekly Reader, October 12, 1950, "Military secret of the United States of America Air Forces", (flying saucers are US Air Force experimental aircraft).
- Popular Mechanics, January 1995; "Flying Saucers Are Real", (real aircraft from the planet Earth).
- Rose, Bill; Tony Buttler. Secret Projects: Flying Saucer Aircraft, Midland Publishing, 2004 ISBN 978-1-85780-233-7