A product's service life is its period of use in service. It has been defined as "a product's total life in use from the point of sale to the point of discard" and distinguished from replacement life,"the period after which the initial purchaser returns to the shop for a replacement." Determining a product´s expected service life as part of business policy involves using tools and calculations from maintainability and reliability analysis. Service life represents a commitment made by the item's manufacturer and is usually specified as a median. It is the time that any manufactured item can be expected to be 'serviceable' or supported by its manufacturer.
Service life is not to be confused with shelf life, which deals with storage time, or with technical life, which is the maximumn period during which it can physically function. It also differs from predicted life, or MTTF/MTBF (Mean Time to Failure/Mean Time Between Failures)/MFOP (maintenance-free operating period). Predicted life is useful such that a manufacturer may estimate, by hypothetical modeling and calculation, a general rule for which it will honor warranty claims, or planning for mission fulfillment. The difference between service life and predicted life is most clear when considering mission time and reliability in comparison to MTBF and service life. For example: A missile system can have a mission time of less than one minute, a service life of 20 years, active MTBF of 20 minutes, dormant MTBF of 50 years and a reliability of .999999.
Manufacturers will commit to very conservative service life, usually 2 to 5 years for most commercial and consumer products (for example computer peripherals and components). However, for large and expensive durable goods, the items are not consumable, and service lives and maintenance activity will factor large in the service life. Again, an airliner might have a mission time of 11 hours, a predicted active MTBF of 10,000 hours with maintenance (or 15,000 hours without maintenance), a reliability of .99999 and a service life of 40 years.
The most common model for item lifetime is the bathtub curve, a plot of the varying failure rate as a function of time. During early life, the bathtub shows increased failures, usually witnessed during product development. The middle portion of the bathtub, or 'useful life', is a slightly inclined, nearly constant failure rate period where the consumer enjoys the benefit conferred by the product. As the time increases further, the curve reaches a period of increasing failures, modeling the product's wearout phase.
For an individual product, the component parts may each have independent service lives, resulting in several bathtub curves. For instance, a tire will have a service life partitioning related to the tread and the casing.
For maintainable items, those wear-out items that are determined by logistical analysis to be provisioned for sparing and replacement will assure a longer service life than manufactured items without such planning. A simple example is automotive tires - failure to plan for this wear out item would limit automotive service life to the extent of a single set of tires.
An individual tire's life follows the bathtub curve, to boot. After installation, there is a not-small probability of failure which may be related to material or workmanship or even to the process for mounting the tire which may introduce some small damage. After the initial period, the tire will perform, given no defect introducing event such as encountering a road hazard (a nail or a pothole), for a long duration relative to its expected service life which is a function of several variables (design, material, process). After a period, the failure probability will rise; for some tires, this will occur after the tread is worn out. Then, a secondary market for tires puts a retread on the tire thereby extending the service life. It is not uncommon for an 80,000-mile tire to perform well beyond that limit.
It may be difficult to obtain reliable longevity data about many consumer products as, in general, efforts at actuarial analysis are not taken to the same extent as found with that needed to support insurance decisions. However, some attempts to provide this type of information have been made. An example is the collection of estimates for household components provided by the Old House Web which gathers data from the Appliance Statistical Review and various institutes involved with the homebuilding trade.
Some Engine manufacturers, such as for example Navistar and Volvo, use a so called B-life rating, based on the durability data of the engine manufacturer, B10 and B50 index for measuring the life expectancy of an engine.
BOL and EOL
For certain products, such as those that cannot be serviced during their operational life for technical reasons, a manufacturer may calculate a product's expected performance at both the beginning of operational life (BOL) and end of operational life (EOL). Batteries and other components that degrade over time may affect the operation of a product. The performance of mission critical components is therefore calculated for EOL, with the components exceeding their specification at BOL. For example, with spaceflight hardware, which must survive in the harsh environment of space, the capacity to generate electricity from solar panels or radioisotope thermoelectric generator is likely to reduce throughout a mission, but must still meet a specific requirement at EOL in order to complete the mission. A spacecraft may also have a BOL mass that is greater than its EOL mass as propellant is depleted during its operational life.
- Cooper, Tim (1994). Beyond Recycling: the longer life option. London: New Economics Foundation. p. 5. ISBN 9781889407005.
- Evans, Sian; Cooper, Tim (2010). "Consumer Influences on Product Life-Spans". In Cooper, Tim. Longer Lasting Products. Farnham: Gower. pp. 319–350. ISBN 9780566088087.
- "Drive it forever" Club Lexus Forums
- Tire Retread Information Bureau
- Old House Web, "Life Expectancy of Household Components