Properties of water
|Molar mass||18.01528(33) g/mol|
|Appearance||white solid or almost colorless, transparent, with a slight hint of blue, crystalline solid or liquid|
|Density||999.9720 kg/m3 ≈ 1 t/m3 = 1 kg/l = 1 g/cm3 ≈ 62.4 lb/ft3 (liquid, maximum, at ~4 °C)
917 kg/m3 (solid)
|Melting point||0.00 °C (32.00 °F; 273.15 K) |
|Boiling point||100 °C (212 °F; 373 K) |
|Solubility||Poorly soluble in haloalkanes, aliphatic and aromatic hydrocarbons, ethers. Improved solubility in carboxylates, alcohols, ketones, amines. Miscible with methanol, ethanol, isopropanol, acetone, glycerol.|
|Vapor pressure||see text|
|−1.298·10−5 cm3/mol (20 °C, 1 atm)|
|Thermal conductivity||0.58 W/m·K|
Refractive index (nD)
|Viscosity||1 cP (20 °C)|
|75.375 ±0.05 J/mol·K|
Std enthalpy of
Gibbs free energy (ΔfG˚)
|Main hazards||Drowning (see also Dihydrogen monoxide hoax)
Avalanche (as snow)
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
|what is: / ?)(|
2O) is the most abundant compound on Earth's surface, covering 70 percent of the planet. In nature, water exists in liquid, solid, and gaseous states. It is in dynamic equilibrium between the liquid and gas states at standard temperature and pressure. At room temperature, it is a tasteless and odorless liquid, nearly colorless with a hint of blue. Many substances dissolve in water and it is commonly referred to as the universal solvent. Because of this, water in nature and in use is rarely pure and some properties may vary from those of the pure substance. However, there are also many compounds that are essentially, if not completely, insoluble in water. Water is the only common substance found naturally in all three common states of matter and it is essential for all life on Earth. Water makes up 55% to 78% of the human body.
- 1 Forms of water
- 2 Physics and chemistry
- 2.1 Water, ice, and vapor
- 2.2 Electrical properties
- 2.3 Static dielectric constant
- 2.4 Polarity, hydrogen bonding and inter-molecular structure
- 2.5 Water in acid-base reactions
- 2.6 Water in redox reactions
- 2.7 Geochemistry
- 2.8 Transparency
- 2.9 Heavy water and isotopologues
- 3 History
- 4 Systematic naming
- 5 See also
- 6 Notes
- 7 References
- 8 External links
Forms of water
Like many substances, water can take numerous forms that are broadly categorized by phase of matter. The liquid phase is the most common among water's phases (within the Earth's atmosphere and surface) and is the form that is generally denoted by the word "water." The solid phase of water is known as ice and commonly takes the structure of hard, amalgamated crystals, such as ice cubes, or loosely accumulated granular crystals, like snow. For a list of the many different crystalline and amorphous forms of solid H2O, see the article ice. The gaseous phase of water is known as water vapor (or steam), and is characterized by water assuming the configuration of a transparent cloud. (Note that visible steam and clouds are, in fact, water in the liquid form as minute droplets suspended in the air.) The fourth state of water, that of a supercritical fluid, is much less common than the other three and only rarely occurs in nature, in extremely uninhabitable conditions. When water achieves a specific critical temperature and a specific critical pressure (647 K and 22.064 MPa), liquid and gas phase merge to one homogeneous fluid phase, with properties of both gas and liquid. One example of naturally occurring supercritical water is found in the hottest parts of deep water hydrothermal vents, in which water is heated to the critical temperature by scalding volcanic plumes and achieves the critical pressure because of the crushing weight of the ocean at the extreme depths at which the vents are located. Additionally, anywhere there is volcanic activity below a depth of 2.25 km (1.40 mi) can be expected to have water in the supercritical phase.
Vienna Standard Mean Ocean Water is the current international standard for water isotopes. Naturally occurring water is almost completely composed of the neutron-less hydrogen isotope protium. Only 155 ppm include deuterium (2
H or D), a hydrogen isotope with one neutron, and fewer than 20 parts per quintillion include tritium (3
H or T), which has two.
In keeping with the basic rules of chemical nomenclature, water would have a systematic name of dihydrogen monoxide, but this is not among the names published by the International Union of Pure and Applied Chemistry and, rather than being used in a chemical context, the name is almost exclusively used as a humorous way to refer to water.
Heavy water is water with a higher-than-average deuterium content, up to 100%. Chemically, it is similar but not identical to normal water. This is because the nucleus of deuterium is twice as heavy as protium, and this causes noticeable differences in bonding energies. Because water molecules exchange hydrogen atoms with one another, hydrogen deuterium oxide (DOH) is much more common in low-purity heavy water than pure dideuterium monoxide (D2O). Humans are generally unaware of taste differences, but sometimes report a burning sensation or sweet flavor. Rats, however, are able to avoid heavy water by smell. Toxic to many animals, heavy water is used in the nuclear reactor industry to moderate (slow down) neutrons. Light water reactors are also common, where "light" simply designates normal water.
Light water more specifically refers to deuterium-depleted water (DDW), water in which the deuterium content has been reduced below the standard 155 ppm level.
Physics and chemistry
Water is the chemical substance with chemical formula H
2O one molecule of water has two hydrogen atoms covalently bonded to a single oxygen atom. Water is a tasteless, odorless liquid at ambient temperature and pressure, and appears colorless in small quantities, although it has its own intrinsic very light blue hue. Ice also appears colorless, and water vapor is essentially invisible as a gas.
Water is primarily a liquid under standard conditions, which is not predicted from its relationship to other analogous hydrides of the oxygen family in the periodic table, which are gases such as hydrogen sulfide. The elements surrounding oxygen in the periodic table, nitrogen, fluorine, phosphorus, sulfur and chlorine, all combine with hydrogen to produce gases under standard conditions. The reason that water forms a liquid is that oxygen is more electronegative than all of these elements with the exception of fluorine. Oxygen attracts electrons much more strongly than hydrogen, resulting in a net positive charge on the hydrogen atoms, and a net negative charge on the oxygen atom. The presence of a charge on each of these atoms gives each water molecule a net dipole moment. Electrical attraction between water molecules due to this dipole pulls individual molecules closer together, making it more difficult to separate the molecules and therefore raising the boiling point. This attraction is known as hydrogen bonding. The molecules of water are constantly moving in relation to each other, and the hydrogen bonds are continually breaking and reforming at timescales faster than 200 femtoseconds. However, this bond is sufficiently strong to create many of the peculiar properties of water, such as those that make it integral to life. Water can be described as a polar liquid that slightly dissociates disproportionately into the hydronium ion (H
(aq)) and an associated hydroxide ion (OH−
- 2 H
(aq) + OH−
Percentage of elements in water by mass: 11.1% hydrogen, 88.9% oxygen.
The self-diffusion coefficient of water is 2.299·10−9 m2·s−1.
Water, ice, and vapor
Heat capacity and heats of vaporization and fusion
|Temperature (°C)||Hv (kJ/mol)|
Water has a very high specific heat capacity – the second highest among all the heteroatomic species (after ammonia), as well as a high heat of vaporization (40.65 kJ/mol or 2257 kJ/kg at the normal boiling point), both of which are a result of the extensive hydrogen bonding between its molecules. These two unusual properties allow water to moderate Earth's climate by buffering large fluctuations in temperature. According to Josh Willis, of NASA's Jet Propulsion Laboratory, the oceans absorb one thousand times more heat than the atmosphere (air) and are holding 80 to 90% of the heat of global warming.
The specific enthalpy of fusion of water is 333.55 kJ/kg at 0 °C, i.e. melting ice absorbs the same energy as ice warming from -160 degrees Celsius up to its melting point. Similarly the heat needed to melt ice at 0°C, would heat the same amount of water by about 80°C. Of common substances, only that of ammonia is higher. This property confers resistance to melting on the ice of glaciers and drift ice. Before and since the advent of mechanical refrigeration, ice was and still is in common use for retarding food spoilage.
|Temperature (°C)||Cp (J/(g·K) at 100 kPa)|
Density of water and ice
|Temp (°C)||Density (kg/m3)|
|The values below 0 °C refer to supercooled water.|
The density of water is approximately one gram per cubic centimeter. It is dependent on its temperature, but the relation is not linear and is unimodal rather than monotonic (see table at left). When cooled from room temperature liquid water becomes increasingly dense, as with other substances, but at approximately 4 °C (39 °F), pure water reaches its maximum density. As it is cooled further, it expands to become less dense. This unusual negative thermal expansion is attributed to strong, orientation-dependent, intermolecular interactions and is also observed in molten silica.
The solid form of most substances is denser than the liquid phase; thus, a block of most solids will sink in the liquid. However, a block of ice floats in liquid water because ice is less dense. Upon freezing, the density of water decreases by about 9%. This is due to the 'cooling' of intermolecular vibrations allowing the molecules to form steady hydrogen bonds with their neighbors and thereby gradually locking into positions reminiscent of the hexagonal packing achieved upon freezing to ice Ih. Whereas the hydrogen bonds are shorter in the crystal than in the liquid, this locking effect reduces the average coordination number of molecules as the liquid approaches nucleation. Other substances that expand on freezing are silicon, gallium, germanium, antimony, bismuth, plutonium and also chemical compounds that form spacious crystal lattices with tetrahedral coordination.
Only ordinary hexagonal ice is less dense than the liquid. Under increasing pressure, ice undergoes a number of transitions to other allotropic forms with higher density than liquid water, such as ice II, ice III, high-density amorphous ice (HDA), and very-high-density amorphous ice (VHDA).
Water also expands significantly as the temperature increases. Water near the boiling point is about 96% as dense as water at 4 °C.
The melting point of ice is 0 °C (32 °F, 273.15 K) at standard pressure, however, pure liquid water can be supercooled well below that temperature without freezing if the liquid is not mechanically disturbed. It can remain in a fluid state down to its homogeneous nucleation point of approximately 231 K (−42 °C). The melting point of ordinary hexagonal ice falls slightly under moderately high pressures, but as ice transforms into its allotropes (see crystalline states of ice) above 209.9 MPa (2,072 atm), the melting point increases markedly with pressure, i.e., reaching 355 K (82 °C) at 2.216 GPa (21,870 atm) (triple point of Ice VII).
A significant increase of pressure is required to lower the melting point of ordinary ice—the pressure exerted by an ice skater on the ice only reduces the melting point by approximately 0.09 °C (0.16 °F).
These properties of water have important consequences in its role in Earth's ecosystem. Water at a temperature of 4 °C (39.2 °F) will always accumulate at the bottom of freshwater lakes, irrespective of the temperature in the atmosphere.
In cold countries, when the temperature of fresh water reaches 4 °C, the layers of water near the top in contact with cold air continue to lose heat energy and their temperature falls below 4 °C. On cooling below 4 °C, these layers do not sink as fresh water has a maximum density at 4 °C. (Refer: Polarity and hydrogen bonding) Due to this, the layer of water at 4 °C remains at the bottom and above this layers of water 3 °C, 2 °C, 1 °C and 0 °C are formed. As water at 0 °C is the least dense it floats on the top and turns into ice as the water continues to cool. Ice growth continues on the bottom of the ice as heat is drawn away through the ice (the heat conductivity of ice is similar to glass). All the while the water further down below the ice is still 4 °C. As the ice layer shields the lake from the effect of the wind, water in the lake will no longer turn over. Although both water and ice are relatively good conductors of heat, a thick layer of ice and a thick layer of stratified water under the ice slow down further heat loss from the lake relative to when the lake was exposed. It is, therefore, unlikely that sufficiently deep lakes will freeze completely, unless stirred by strong currents that mix cooler and warmer water and accelerate the cooling. Thus, as long as the pond or lake does not freeze up completely, aquatic creatures are not exposed to freezing temperatures. In warming weather, chunks of ice float, rather than sink to the bottom where they might melt extremely slowly. These properties therefore allow aquatic life in the lake to survive during the winter.
Density of saltwater and ice
The density of water is dependent on the dissolved salt content as well as the temperature of the water. Ice still floats in the oceans, otherwise they would freeze from the bottom up. However, the salt content of oceans lowers the freezing point by about 2 °C (see here for explanation) and lowers the temperature of the density maximum of water to the freezing point. This is why, in ocean water, the downward convection of colder water is not blocked by an expansion of water as it becomes colder near the freezing point. The oceans' cold water near the freezing point continues to sink. For this reason, any creature attempting to survive at the bottom of such cold water as the Arctic Ocean generally lives in water that is 4 °C colder than the temperature at the bottom of frozen-over fresh water lakes and rivers in the winter.
As the surface of salt water begins to freeze (at −1.9 °C for normal salinity seawater, 3.5%) the ice that forms is essentially salt free with a density approximately equal to that of freshwater ice. This ice floats on the surface and the salt that is "frozen out" adds to the salinity and density of the seawater just below it, in a process known as brine rejection. This denser saltwater sinks by convection and the replacing seawater is subject to the same process. This provides essentially freshwater ice at −1.9 °C on the surface. The increased density of the seawater beneath the forming ice causes it to sink towards the bottom. On a large scale, the process of brine rejection and sinking cold salty water results in ocean currents forming to transport such water away from the Poles, leading to a global system of currents called the thermohaline circulation.
Miscibility and condensation
Water is miscible with many liquids, for example ethanol in all proportions, forming a single homogeneous liquid. On the other hand, water and most oils are immiscible usually forming layers according to increasing density from the top. This can be predicted by comparing the polarity. Water being a relatively polar compound will tend to be miscible with liquids of high polarity such as ethanol and acetone whereas compounds with low polarity will tend to be immiscible and poorly soluble such as with hydrocarbons.
As a gas, water vapor is completely miscible with air. On the other hand, the maximum water vapor pressure that is thermodynamically stable with the liquid (or solid) at a given temperature is relatively low compared with total atmospheric pressure. For example, if the vapor partial pressure is 2% of atmospheric pressure and the air is cooled from 25 °C, starting at about 22 °C water will start to condense, defining the dew point, and creating fog or dew. The reverse process accounts for the fog burning off in the morning. If the humidity is increased at room temperature, for example, by running a hot shower or a bath, and the temperature stays about the same, the vapor soon reaches the pressure for phase change, and then condenses out as minute water droplets, commonly referred to as steam.
A gas in this context is referred to as saturated or 100% relative humidity, when the vapor pressure of water in the air is at the equilibrium with vapor pressure due to (liquid) water; water (or ice, if cool enough) will fail to lose mass through evaporation when exposed to saturated air. Because the amount of water vapor in air is small, relative humidity, the ratio of the partial pressure due to the water vapor to the saturated partial vapor pressure, is much more useful. Water vapor pressure above 100% relative humidity is called super-saturated and can occur if air is rapidly cooled, for example, by rising suddenly in an updraft.
The compressibility of water is a function of pressure and temperature. At 0 °C, at the limit of zero pressure, the compressibility is ×10−10 Pa−1. 5.1 At the zero-pressure limit, the compressibility reaches a minimum of ×10−10 Pa−1 around 45 °C before increasing again with increasing temperature. As the pressure is increased, the compressibility decreases, being 4.4×10−10 Pa−1 at 0 °C and 100 MPa. 3.9
The bulk modulus of water is about 2.2 GPa. The low compressibility of non-gases, and of water in particular, leads to their often being assumed as incompressible. The low compressibility of water means that even in the deep oceans at 4 km depth, where pressures are 40 MPa, there is only a 1.8% decrease in volume.
|Phases in stable equilibrium||Pressure||Temperature|
|liquid water, ice Ih, and water vapor||611.73 Pa||273.16 K (0.01 °C)|
|liquid water, ice Ih, and ice III||209.9 MPa||251 K (−22 °C)|
|liquid water, ice III, and ice V||350.1 MPa||−17.0 °C|
|liquid water, ice V, and ice VI||632.4 MPa||0.16 °C|
|ice Ih, Ice II, and ice III||213 MPa||−35 °C|
|ice II, ice III, and ice V||344 MPa||−24 °C|
|ice II, ice V, and ice VI||626 MPa||−70 °C|
The temperature and pressure at which solid, liquid, and gaseous water coexist in equilibrium is called the triple point of water. This point is used to define the units of temperature (the kelvin, the SI unit of thermodynamic temperature and, indirectly, the degree Celsius and even the degree Fahrenheit).
As a consequence, water's triple point temperature, as measured in these units, is a prescribed value rather than a measured quantity.
This pressure is quite low, about 1⁄166 of the normal sea level barometric pressure of 101,325 Pa. The atmospheric surface pressure on planet Mars is 610.5 Pa, which is remarkably close to the triple point pressure. The altitude of this surface pressure was used to define zero-elevation or "sea level" on that planet.
Although it is commonly named as "the triple point of water", the stable combination of liquid water, ice I, and water vapor is but one of several triple points on the phase diagram of water. Gustav Heinrich Johann Apollon Tammann in Göttingen produced data on several other triple points in the early 20th century. Kamb and others documented further triple points in the 1960s.
Pure water containing no exogenous ions is an excellent insulator, but not even "deionized" water is completely free of ions. Water undergoes auto-ionization in the liquid state, when two water molecules form one hydroxide anion (OH−) and one hydronium cation (H
Because water is such a good solvent, it almost always has some solute dissolved in it, often a salt. If water has even a tiny amount of such an impurity, then it can conduct electricity far more readily.
It is known that the theoretical maximum electrical resistivity for water is approximately 182 kΩ·m at 25 °C. This figure agrees well with what is typically seen on reverse osmosis, ultra-filtered and deionized ultra-pure water systems used, for instance, in semiconductor manufacturing plants. A salt or acid contaminant level exceeding even 100 parts per trillion (ppt) in otherwise ultra-pure water begins to noticeably lower its resistivity by up to several kΩ·m.
In pure water, sensitive equipment can detect a very slight electrical conductivity of 0.055 µS/cm at 25 °C. Water can also be electrolyzed into oxygen and hydrogen gases but in the absence of dissolved ions this is a very slow process, as very little current is conducted. In ice, the primary charge carriers are protons (see proton conductor).
Water can be split into its constituent elements, hydrogen and oxygen, by passing an electric current through it. This process is called electrolysis. Water molecules naturally dissociate into H+
ions, which are attracted toward the cathode and anode, respectively. At the cathode, two H+
ions pick up electrons and form H
2 gas. At the anode, four OH−
ions combine and release O
2 gas, molecular water, and four electrons. The gases produced bubble to the surface, where they can be collected. The standard potential of the water electrolysis cell (when heat is added to the reaction) is a minimum of 1.23 V at 25 °C. The operating potential is actually 1.48 V (or above) in practical electrolysis when heat input is negligible.
Static dielectric constant
One of the important properties of water is that it has a high dielectric constant. This constant shows its ability to make electrostatic bonds with other molecules, meaning it can eliminate the attraction of the opposite charges of the surrounding ions.
Polarity, hydrogen bonding and inter-molecular structure
An important feature of water is its polar nature. The structure has a bent molecular geometry for the two hydrogens from the oxygen vertex. The oxygen atom also has two lone pairs of electrons. One effect usually ascribed to the lone pairs is that the H–O–H gas phase bend angle is 104.48°, which is smaller than the typical tetrahedral angle of 109.47°. The lone pair orbitals are more diffuse than the bond orbitals to the hydrogens; the increased repulsion of the lone pairs forces the O–H bonds closer to each other.
Another effect of the electronic structure is that water is a polar molecule. There is a bond dipole moment pointing from each H to the O, making the oxygen partially negative and the hydrogen partially positive. In addition, the O also has nonbonded electrons in the direction opposite the hydrogen atoms. There is thus a large molecular dipole, pointing from a positive region between the two hydrogen atoms to the negative region of the oxygen atom. The charge differences cause water molecules to be attracted to each other (the relatively positive areas being attracted to the relatively negative areas) and to other polar molecules. This attraction contributes to hydrogen bonding, and explains many of the properties of water, such as solvent action.
Although hydrogen bonding is a relatively weak attraction compared to the covalent bonds within the water molecule itself, it is responsible for a number of water's physical properties. One such property is its relatively high melting and boiling point temperatures; more energy is required to break the hydrogen bonds between water molecules. In contrast, hydrogen sulfide (H
2S), has much weaker hydrogen bonding due to sulfur's lower electronegativity.H
2S is a gas at room temperature, in spite of hydrogen sulfide having nearly two times the molar mass of water. The extra bonding between water molecules also gives liquid water a large specific heat capacity. This high heat capacity makes water a good heat storage medium (coolant) and heat shield.
A single water molecule can participate in a maximum of four hydrogen bonds because it can accept two bonds using the lone pairs on oxygen and donate two hydrogen atoms. Other molecules like hydrogen fluoride, ammonia and methanol can also form hydrogen bonds. However they do not show anomalous thermodynamic, kinetic or structural properties like those observed in water. The answer to the apparent difference between water and other hydrogen bonding liquids lies in the fact that apart from water none of these examples participate in four hydrogen bonds; this is either due to an inability to donate or accept hydrogens or is due to steric effects in bulky residues. In water, intermolecular tetrahedral structures form due to the four hydrogen bonds gives rise to an open structure and a 3-dimensional bonding network, resulting in the anomalous decrease of density when cooled below 4 °C. This repeated, constantly reorganizing unit defines a three-dimensional network extending throughout the liquid. This view is based upon neutron scattering studies and computer simulations, and it makes sense in the light of the unambiguously tetrahedral arrangement of water molecules in ice structures.
However, there is an alternative theory for the structure of water. In 2004, a controversial paper published in science, from Stockholm University in Sweden, suggested that water molecules in liquid form, bind on average to not four but only two others; hence forming chains and rings. it was coined the term "string theory of water (not to be confused with string theory in physics). These observations were based upon X-ray absorption spectroscopy to probe the local environment of individual oxygen atoms. Water, the team now suggests, is a muddle of the two proposed structures. They say that it is a soup flecked with "ice bergs" each comprising 100 or so loosely connected molecules that are relatively open and hydrogen bonded. The soup is made of the string structure and the icebergs of the tetrahedral structure.
Cohesion and adhesion
Water molecules stay close to each other (cohesion), due to the collective action of hydrogen bonds between water molecules. These hydrogen bonds are constantly breaking, with new bonds being formed with different water molecules; but at any given time in a sample of liquid water, a large portion of the molecules are held together by such bonds.
Water also has high adhesion properties because of its polar nature. On extremely clean/smooth glass the water may form a thin film because the molecular forces between glass and water molecules (adhesive forces) are stronger than the cohesive forces. In biological cells and organelles, water is in contact with membrane and protein surfaces that are hydrophilic; that is, surfaces that have a strong attraction to water. Irving Langmuir observed a strong repulsive force between hydrophilic surfaces. To dehydrate hydrophilic surfaces—to remove the strongly held layers of water of hydration—requires doing substantial work against these forces, called hydration forces. These forces are very large but decrease rapidly over a nanometer or less. They are important in biology, particularly when cells are dehydrated by exposure to dry atmospheres or to extracellular freezing.
Water has a high surface tension of 72.8 mN/m at room temperature, caused by the strong cohesion between water molecules, the highest of the common non-ionic, non-metallic liquids. This can be seen when small quantities of water are placed onto a sorption-free (non-adsorbent and non-absorbent) surface, such as polyethylene or Teflon, and the water stays together as drops. Just as significantly, air trapped in surface disturbances forms bubbles, which sometimes last long enough to transfer gas molecules to the water.
Another surface tension effect is capillary waves, which are the surface ripples that form around the impacts of drops on water surfaces, and sometimes occur with strong subsurface currents flowing to the water surface. The apparent elasticity caused by surface tension drives the waves.
Due to an interplay of the forces of adhesion and surface tension, water exhibits capillary action whereby water rises into a narrow tube against the force of gravity. Water adheres to the inside wall of the tube and surface tension tends to straighten the surface causing a surface rise and more water is pulled up through cohesion. The process continues as the water flows up the tube until there is enough water such that gravity balances the adhesive force.
Surface tension and capillary action are important in biology. For example, when water is carried through xylem up stems in plants, the strong intermolecular attractions (cohesion) hold the water column together and adhesive properties maintain the water attachment to the xylem and prevent tension rupture caused by transpiration pull.
Water as a solvent
Water is also a good solvent, due to its polarity. Substances that will mix well and dissolve in water (e.g. salts) are known as hydrophilic ("water-loving") substances, while those that do not mix well with water (e.g. fats and oils), are known as hydrophobic ("water-fearing") substances. The ability of a substance to dissolve in water is determined by whether or not the substance can match or better the strong attractive forces that water molecules generate between other water molecules. If a substance has properties that do not allow it to overcome these strong intermolecular forces, the molecules are "pushed out" from the water, and do not dissolve. Contrary to the common misconception, water and hydrophobic substances do not "repel", and the hydration of a hydrophobic surface is energetically, but not entropically, favorable.
When an ionic or polar compound enters water, it is surrounded by water molecules (Hydration). The relatively small size of water molecules (~ 3 Angstroms) allows many water molecules to surround one molecule of solute. The partially negative dipole ends of the water are attracted to positively charged components of the solute, and vice versa for the positive dipole ends.
In general, ionic and polar substances such as acids, alcohols, and salts are relatively soluble in water, and non-polar substances such as fats and oils are not. Non-polar molecules stay together in water because it is energetically more favorable for the water molecules to hydrogen bond to each other than to engage in van der Waals interactions with non-polar molecules.
An example of an ionic solute is table salt; the sodium chloride, NaCl, separates into Na+
cations and Cl−
anions, each being surrounded by water molecules. The ions are then easily transported away from their crystalline lattice into solution. An example of a nonionic solute is table sugar. The water dipoles make hydrogen bonds with the polar regions of the sugar molecule (OH groups) and allow it to be carried away into solution.
Water in acid-base reactions
Chemically, water is amphoteric: it has the rare ability to act as either an acid or a base in chemical reactions. According to the Brønsted-Lowry definition, an acid is defined as a species which donates a proton (a H+
ion) in a reaction, and a base as one which receives a proton. When reacting with a stronger acid, water acts as a base; when reacting with a stronger base, it acts as an acid. For instance, water receives an H+
ion from HCl when hydrochloric acid is formed:
- HCl (acid) + H
2O (base) H
In the reaction with ammonia, NH
3, water donates a H+
ion, and is thus acting as an acid:
3 (base) + H
2O (acid) NH+
4 + OH−
Because the oxygen atom in water has two lone pairs, water often acts as a Lewis base, or electron pair donor, in reactions with Lewis acids, although it can also react with Lewis bases, forming hydrogen bonds between the electron pair donors and the hydrogen atoms of water. HSAB theory describes water as both a weak hard acid and a weak hard base, meaning that it reacts preferentially with other hard species:
(Lewis acid) + H
2O (Lewis base) → H
(Lewis acid) + H
2O (Lewis base) → Fe(H
(Lewis base) + H
2O (Lewis acid) → Cl(H
When a salt of a weak acid or of a weak base is dissolved in water, water can partially hydrolyze the salt, producing the corresponding base or acid, which gives aqueous solutions of soap and baking soda their basic pH:
3 + H
2O NaOH + NaHCO
Water's Lewis base character makes it a common ligand in transition metal complexes, examples of which range from solvated ions, such as Fe(H
6, to perrhenic acid, which contains two water molecules coordinated to a rhenium atom, to various solid hydrates, such as CoCl
2O. Water is typically a monodentate ligand, it forms only one bond with the central atom.
As a hard base, water reacts readily with organic carbocations, for example in hydration reaction, in which a hydroxyl group (OH−
) and an acidic proton are added to the two carbon atoms bonded together in the carbon-carbon double bond, resulting in an alcohol. When addition of water to an organic molecule cleaves the molecule in two, hydrolysis is said to occur. Notable examples of hydrolysis are saponification of fats and digestion of proteins and polysaccharides. Water can also be a leaving group in SN2 substitution and E2 elimination reactions, the latter is then known as dehydration reaction.
Acidity in nature
Pure water has the concentration of hydroxide ions (OH−
) equal to that of the hydronium (H
) or hydrogen (H+
) ions, which gives pH of 7 at 298 K. In practice, pure water is very difficult to produce. Water left exposed to air for any length of time will dissolve carbon dioxide, forming a dilute solution of carbonic acid, with a limiting pH of about 5.7. As cloud droplets form in the atmosphere and as raindrops fall through the air minor amounts of CO
2 are absorbed, and thus most rain is slightly acidic. If high amounts of nitrogen and sulfur oxides are present in the air, they too will dissolve into the cloud and rain drops, producing acid rain.
Water in redox reactions
Water contains hydrogen in oxidation state +1 and oxygen in oxidation state −2. Because of that, water oxidizes chemicals with reduction potential below the potential of H+
2, such as hydrides, alkali and alkaline earth metals, etc. Some other reactive metals, such as aluminum and beryllium, are oxidized by water as well, but their oxides are not soluble, and the reaction stops because of passivation. Note, however, that rusting of iron is a reaction between iron and oxygen, dissolved in water, not between iron and water.
- 2 Na + 2 H
2O → 2 NaOH + H
Water itself can be oxidized, emitting oxygen gas, but very few oxidants react with water even if their reduction potential is greater than the potential of O
2O. Almost all such reactions require a catalyst.
- 4 AgF
2 + 2 H
2O → 4 AgF + 4 HF + O
Action of water on rock over long periods of time typically leads to weathering and water erosion, physical processes that convert solid rocks and minerals into soil and sediment, but under some conditions chemical reactions with water occur as well, resulting in metasomatism or mineral hydration, a type of chemical alteration of a rock which produces clay minerals in nature and also occurs when Portland cement hardens.
Water ice can form clathrate compounds, known as clathrate hydrates, with a variety of small molecules that can be embedded in its spacious crystal lattice. The most notable of these is methane clathrate, 4 CH
4·23 ḥ, naturally found in large quantities on the ocean floor.
Water is relatively transparent to visible light, near ultraviolet light, and far-red light, but it absorbs most ultraviolet light, infrared light, and microwaves. Most photoreceptors and photosynthetic pigments utilize the portion of the light spectrum that is transmitted well through water. Microwave ovens take advantage of water's opacity to microwave radiation to heat the water inside of foods. The very weak onset of absorption in the red end of the visible spectrum lends water its intrinsic blue hue (see Color of water).
Heavy water and isotopologues
Hydrogen occurs naturally in three isotopes. The most common (1H) accounting for more than 99.98% of hydrogen in water, consists of only a single proton in its nucleus. A second, stable isotope, deuterium (chemical symbol D or 2H), has an additional neutron. Deuterium oxide, D
2O, is also known as heavy water because of its higher density. It is used in nuclear reactors as a neutron moderator. The third isotope, tritium, has 1 proton and 2 neutrons, and is radioactive, decaying with a half-life of 4500 days. THO exists in nature only in minute quantities, being produced primarily via cosmic ray-induced nuclear reactions in the atmosphere. Water with one deuterium atom HDO occurs naturally in ordinary water in low concentrations (~0.03%) and D
2O in far lower amounts (0.000003%).
The most notable physical differences between H
2O and D
2O, other than the simple difference in specific mass, involve properties that are affected by hydrogen bonding, such as freezing and boiling, and other kinetic effects. The difference in boiling points allows the isotopologues to be separated. The self-diffusion coefficient of H
2O at 25 °C is 23% higher than the value of D
Consumption of pure isolated D
2O may affect biochemical processes – ingestion of large amounts impairs kidney and central nervous system function. Small quantities can be consumed without any ill-effects, and even very large amounts of heavy water must be consumed for any toxicity to become apparent.
Oxygen also has three stable isotopes, with 16
O present in 99.76%, 17
O in 0.04%, and 18
O in 0.2% of water molecules.
The first decomposition of water into hydrogen and oxygen, by electrolysis, was done in 1800 by English chemist William Nicholson. In 1805, Joseph Louis Gay-Lussac and Alexander von Humboldt showed that water is composed of two parts hydrogen and one part oxygen.
The properties of water have historically been used to define various temperature scales. Notably, the Kelvin, Celsius, Rankine, and Fahrenheit scales were, or currently are, defined by the freezing and boiling points of water. The less common scales of Delisle, Newton, Réaumur and Rømer were defined similarly. The triple point of water is a more commonly used standard point today.
The simplest systematic name of water is hydrogen oxide. This is analogous to related compounds such as hydrogen peroxide, hydrogen sulfide, and deuterium oxide (heavy water). Another systematic name, oxidane, is accepted by IUPAC as a parent name for the systematic naming of oxygen-based substituent groups, although even these commonly have other recommended names. For example, the name hydroxyl is recommended over oxidanyl for the –OH group. The name oxane is explicitly mentioned by the IUPAC as being unsuitable for this purpose, since it is already the name of a cyclic ether also known as tetrahydropyran.
The polarized form of the water molecule, H+OH−, is also called hydron hydroxide by IUPAC nomenclature.
Dihydrogen monoxide (DHMO) is a rarely used name of water. This term has been used in various hoaxes or spoofs that call for this "lethal chemical" to be banned, such as in the dihydrogen monoxide hoax. Other systematic names for water include hydroxic acid, hydroxylic acid, and hydrogen hydroxide. Both acid and alkali names exist for water because it is amphoteric (able to react both as an acid or an alkali). None of these exotic names are used widely.
- Definition of Hydrol Merriam-Webster
- Braun, Charles L.; Sergei N. Smirnov (1993). "Why is water blue?". J. Chem. Educ. 70 (8): 612. Bibcode:1993JChEd..70..612B. doi:10.1021/ed070p612.
- Vienna Standard Mean Ocean Water (VSMOW), used for calibration, melts at 273.1500089(10) K (0.000089(10) °C, and boils at 373.1339 K (99.9839 °C). Other isotopic compositions melt or boil at slightly different temperatures.
- Thermal Conductivity of some common Materials. Engineeringtoolbox.com. Retrieved on 2011-11-22
- Water in Linstrom, P.J.; Mallard, W.G. (eds.) NIST Chemistry WebBook, NIST Standard Reference Database Number 69. National Institute of Standards and Technology, Gaithersburg MD. http://webbook.nist.gov (retrieved 2014-06-01)
- Constant pressure heat capacity of water vs. temperature. Xydatasource.com. Retrieved on 2011-11-22.
- United Nations. Un.org (2005-03-22). Retrieved on 2011-11-22.
- Utz, Jeffrey. Re: What percentage of the human body is composed of water?, The MadSci Network
- 22.064 MPa / ((1 kg × gravity on earth) per liter) = 2.25 km
- Leigh, pp. 27–28.
- Leigh, p. 34.
- Urey, Harold C.; et al. (15 Mar 1935). "Concerning the Taste of Heavy Water". Science 81 (2098) (New York: The Science Press). p. 273. doi:10.1126/science.81.2098.273-a.
- "Experimenter Drinks 'Heavy Water' at $5,000 a Quart". Popular Science Monthly 126 (4) (New York: Popular Science Publishing). Apr 1935. p. 17. Retrieved 7 Jan 2011.
- Müller, Grover C. (June 1937). "Is 'Heavy Water' the Fountain of Youth?". Popular Science Monthly 130 (6) (New York: Popular Science Publishing). pp. 22–23. Retrieved 7 Jan 2011.
- Miller, Inglis J., Jr.; Mooser, Gregory (Jul 1979). "Taste Responses to Deuterium Oxide". Physiology & Behavior 23 (1): 69–74. doi:10.1016/0031-9384(79)90124-0.
- Campbell, Neil A.; Brad Williamson; Robin J. Heyden (2006). Biology: Exploring Life. Boston, Massachusetts: Pearson Prentice Hall. ISBN 0-13-250882-6.
- Smith, Jared D.; Christopher D. Cappa; Kevin R. Wilson; Ronald C. Cohen; Phillip L. Geissler; Richard J. Saykally (2005). "Unified description of temperature-dependent hydrogen bond rearrangements in liquid water" (PDF). Proc. Natl. Acad. Sci. USA 102 (40): 14171–14174. Bibcode:2005PNAS..10214171S. doi:10.1073/pnas.0506899102. PMC 1242322. PMID 16179387.
- Holz, M.; Heil, S. R.; Sacco, A. (2000). "Temperature-dependent self-diffusion coefficients of water and six selected molecular liquids for calibration in accurate 1H NMR PFG Measurements". Phys. Chem. Chem. Phys. 2 (20): 4740–4742. Bibcode:2000PCCP....2.4740H. doi:10.1039/b005319h.
- Haynes, William M., ed. (2011). CRC Handbook of Chemistry and Physics (92nd ed.). Boca Raton, FL: CRC Press. p. 6.5. ISBN 1439855110.
- NASA – Oceans of Climate Change. Nasa.gov (2009-04-22). Retrieved on 2011-11-22.
- Lide, D. R. (Ed.) (1990). CRC Handbook of Chemistry and Physics (70th Edn.). Boca Raton (FL):CRC Press
- Water – Density and Specific Weight. Engineeringtoolbox.com. Retrieved on 2011-11-22
- Shell, Scott M.; Debenedetti, Pablo G. & Panagiotopoulos, Athanassios Z. (2002). "Molecular structural order and anomalies in liquid silica" (PDF). Phys. Rev. E 66: 011202. arXiv:cond-mat/0203383. Bibcode:2002PhRvE..66a1202S. doi:10.1103/PhysRevE.66.011202.
- Smith, Roland (2004) Conquering Chemistry, 4th Ed., McGraw-Hill, Sydney
- Debenedetti, P. G. & Stanley, H. E. (2003). "Supercooled and Glassy Water" (PDF). Physics Today 56 (6): 40–46. Bibcode:2003PhT....56f..40D. doi:10.1063/1.1595053.
- "IAPWS, Release on the pressure along the melting and the sublimation curves of ordinary water substance, 2011". Retrieved 2013-02-19.
- The pressure due to water vapor in the air is called the partial pressure (Dalton's law) and it is directly proportional to the concentration of water molecules in air (Boyle's law).
- Adiabatic cooling resulting from the ideal gas law.
- Brown, Theodore L., H. Eugene LeMay, Jr., and Bruce E. Burston (2006). Chemistry: The Central Science. 10th ed. Upper Saddle River, NJ: Pearson Education, Inc., ISBN 0131096869.
- Fine, R.A. & Millero, F.J. (1973). "Compressibility of water as a function of temperature and pressure". Journal of Chemical Physics 59 (10): 5529. Bibcode:1973JChPh..59.5529F. doi:10.1063/1.1679903.
- Zeitler, W.; Ohlhof, T.; Ebner, H. (2000). "Recomputation of the global Mars control-point network" (PDF). Photogrammetric Engineering & Remote Sensing 66 (2): 155–161. Retrieved 2009-12-26.
- Schlüter, Oliver (2003-07-28). "Impact of High Pressure — Low Temperature Processes on Cellular Materials Related to Foods" (PDF). Technischen Universität Berlin.
- Tammann, Gustav Heinrich Johann Apollon (1925). "The States Of Aggregation". Constable And Company Limited.
- Lewis, William Cudmore McCullagh & Rice, James (1922). A System of Physical Chemistry. Longmans, Green and Co.
- Crofts, A. (1996). "Lecture 12: Proton Conduction, Stoichiometry". University of Illinois at Urbana-Champaign. Retrieved 2009-12-06.
- Hoy, AR; Bunker, PR (1979). "A precise solution of the rotation bending Schrödinger equation for a triatomic molecule with application to the water molecule". Journal of Molecular Spectroscopy 74: 1–8. doi:10.1016/0022-2852(79)90019-5.
- Collins, Tom. "Ask a Scientist: Department of Energy Office of Science". www.newton.dep.anl.gov. Retrieved 21 December 2014.
- Campbell, Mary K. & Farrell, Shawn O. (2007). Biochemistry (6th ed.). Cengage Learning. pp. 37–38. ISBN 978-0-495-39041-1.
- Ball, Philip (2008). "Water an enduring mystery". Nature 452: 291–292. doi:10.1038/452291a. PMID 18354466.
- Campbell, Neil A. & Reece, Jane B. (2009). Biology (8th ed.). Pearson. p. 47. ISBN 978-0-8053-6844-4.
- Chiavazzo, Eliodoro; Fasano, Matteo; Asinari, Pietro; Decuzzi, Paolo. "Scaling behaviour for the water transport in nanoconfined geometries". Nature Communications 5. doi:10.1038/ncomms4565.
- Physical Forces Organizing Biomolecules. biophysics.org
- Charlot, G. (2007). Qualitative Inorganic Analysis. Read Books. p. 275. ISBN 1-4067-4789-0.
- Hardy, Edme H.; Zygar, Astrid; Zeidler, Manfred D.; Holz, Manfred; Sacher, Frank D. (2001). "Isotope effect on the translational and rotational motion in liquid water and ammonia". J. Chem Phys. 114: 3174–3181. doi:10.1063/1.1340584.
- IAPWS (2001). "Guideline on the Use of Fundamental Physical Constants and Basic Constants of Water" (PDF).
- A Brief History of Temperature Measurement. Home.comcast.net. Retrieved on 2011-11-22.
- Mononuclear hydrides in A Guide to IUPAC Nomenclature of Organic Compounds (Recommendations 1993) online version by ACDLabs
- Preamble to chemical nomenclature. IUPAC.
- Leigh, p. 99.
- "hydron hydroxide compound summary at PubChem".
- Leigh, G. J.; et al. (1998). Principles of chemical nomenclature: a guide to IUPAC recommendations (PDF). Blackwell Science Ltd, UK. ISBN 0-86542-685-6.
|Wikimedia Commons has media related to Water molecule.|
|Wikimedia Commons has media related to Water.|
- Water Properties: US Geological Survey's Water Science School. All about water
- Release on the IAPWS Formulation 1995 for the Thermodynamic Properties of Ordinary Water Substance for General and Scientific Use (simpler formulation)
- Online calculator using the IAPWS Supplementary Release on Properties of Liquid Water at 0.1 MPa, September 2008
- Chaplin, Martin. "Water Structure and Science". London South Bank University. Retrieved 2009-07-07.
- Calculation of vapor pressure, liquid density, dynamic liquid viscosity, surface tension of water
- Water Density Calculator
- Why does ice float in my drink?, NASA