In chemical kinetics, the overall rate of a reaction is often approximately determined by the slowest step, known as the rate determining step (RDS) or rate-limiting step. For a given reaction mechanism, the prediction of the corresponding rate equation (for comparison with the experimental rate law) is often simplified by using this approximation of the rate determining step.
In principle, the time evolution of the reactant and product concentrations can be determined from the set of simultaneous rate equations for the individual steps of the mechanism, one for each step. However the analytical solution of these differential equations is not always easy, and in some cases numerical integration may even be required. The hypothesis of a single rate-determining step can greatly simplify the mathematics. In the simplest case the initial step is the slowest, and the overall rate is just the rate of the first step.
Also, the rate equations for mechanisms with a single rate-determining step are usually in a simple mathematical form whose relation to the mechanism and choice of rate-determining step is clear. The correct rate-determining step can be identified by predicting the rate law for each possible choice and comparing the different predictions with the experimental law, as for the example of NO2 and CO below.
Reaction Coordinate Diagram
Given a reaction coordinate (energy diagram), the rate determining step can be determined by taking the largest energy difference between any starting material or intermediate on the diagram and any transition state that comes after it. That transition state will then be the rate-determining step of a given reaction. The transition state with highest absolute energy may not necessarily correspond to the rate determining step.
Example reaction: NO
2 + CO
As an example, consider the gas-phase reaction NO
2 + CO → NO + CO2. If this reaction occurred in a single step, its reaction rate (r) would be proportional to the rate of collisions between NO
2 and CO molecules r = k[NO
2][CO], where k is the reaction rate constant and square brackets indicate a molar concentration.
First step rate-determining
In fact, however, the observed reaction rate is second order in NO
2 and zero order in CO, with rate equation r = k[NO
2]2. This suggests that the rate is determined by a step in which two NO
2 molecules react, with the CO molecule entering at another, faster, step. A possible mechanism in two elementary steps which explains the rate equation is:
2 + NO
2 → NO + NO
3 (slow step, rate-determining)
3 + CO → NO
2 + CO
2 (fast step)
In this mechanism the reactive intermediate species NO
3 is formed in the first step with rate r1 and reacts with CO in the second step with rate r2. However NO
3 can also react with NO if the first step occurs in the reverse direction (NO + NO
3 → 2 NO
2) with rate r-1, where the minus sign indicates the rate of a reverse reaction.
The concentration of a reactive intermediate such as [NO
3] remains low and almost constant. It may therefore be estimated by the steady state approximation, which specifies that the rate at which it is formed equals the (total) rate at which it is consumed. In this example NO
3 is formed in one step and reacts in two, so that
The statement that the first step is the slow step actually means that the first step in the reverse direction is slower than the second step in the forward direction, so that almost all NO
3 is consumed by reaction with CO and not with NO. That is, r-1 << r2, so that r1 – r2 ≈ 0. But the overall rate of reaction is the rate of formation of final product (here CO2), so that r = r2 ≈ r1. That is, the overall rate is determined by the rate of the first step, and (almost) all molecules which react by the first step continue to the second step which is just as fast.
If the second step were rate-determining
The other possible case would be that the second step is slow and rate-determining, meaning that it is slower than the first step in the reverse direction: r2 << r-1. In this hypothesis, r1 – r-1 ≈ 0, so that the first step is (almost) at equilibrium. The overall rate is determined by the second step, r = r2 << r1, as very few molecules which react by the first step continue to the second step which is much slower. However this hypothesis can be rejected (for the example reaction) since it implies a rate equation which disagrees with experiment.
If the first step were at equilibrium, then its equilibrium constant expression permits calculation of the concentration of the intermediate NO
3 in terms of more stable (and more easily measured) reactant and product species
The overall reaction rate would then be
which disagrees with the experimental rate law given above, and so disproves the hypothesis that the second step is rate-determining.
Another example is the unimolecular nucleophilic substitution (SN1) reaction in organic chemistry, where it is the first, rate-determining step that is unimolecular. A specific case is the basic hydrolysis of tert-butyl bromide (t-C
9Br) by aqueous sodium hydroxide. The mechanism has two steps (where R denotes the tert-butyl radical t-C
- Formation of a carbocation R-Br → R+
- Nucleophilic attack by one water molecule R+
This reaction is found to be first-order with rate = k[RBr], which indicates that the first step is slow and determines the rate. The second step with OH− is much faster so the overall rate is independent of the concentration of OH−.
In contrast the alkaline hydrolysis of methyl bromide (CH
3Br) is a bimolecular nucleophilic substitution (SN2) reaction in a single bimolecular step. Its rate law is second-order, rate = k[RBr][OH−
Composition of the transition state
A useful rule in the determination of mechanism is that the concentration factors in the rate law indicate the composition and charge of the activated complex or transition state. For the NO
2-CO reaction above, the rate depends on [NO
2]2 so that the activated complex has composition N
4, with 2 NO
2 entering the reaction before the transition state and CO reacting after the transition state.
which implies an activated complex in which the reactants lose 2H+
before the rate-determining step. The formula of the activated complex is Cl
2 + H
4 – 2 H+
+ x H
2O, or C
x (An unknown number of water molecules are added because the possible dependence of the reaction rate on H
2O was not studied, since the data were obtained in water solvent at a large and essentially unvarying concentration.)
One possible mechanism in which the preliminary steps are known to be rapid is
2 + H
2O HOCl + Cl−
- HOCl + HC
4 → H
2O + Cl−
+ 2 CO2
In the previous examples the rate determining step was one of the sequential chemical reactions leading to a product. The rate-determining step can also be the transport of reactants to where they can interact and form the product. This case is referred to as diffusion control and, in general, occurs when the formation of product from the activated complex is very rapid and thus the provision of the supply of reactants is rate determining.
- Steinfeld J.I., Francisco J.S. and Hase W.L. Chemical Kinetics and Dynamics (2nd ed., Prentice-Hall 1999) chap. 2
- Whitten K.W., Galley K.D. and Davis R.E. General Chemistry (4th edition, Saunders 1992), p.638-9
- Espenson, J.H. (2002). Chemical Kinetics and Reaction Mechanisms (2nd ed.). McGraw-Hill. pp. 127–132. ISBN 0072883626.
- Zumdahl, Steven S. (2005). Chemical Principles (5th ed.). Houghton Mifflin. pp. 727–8. ISBN 0618372067.