In earth science, erosion is the action of surface processes (such as water flow or wind) that remove soil, rock, or dissolved material from one location on the Earth's crust, then transport it away to another location. The particulate breakdown of rock or soil into clastic sediment is referred to as physical or mechanical erosion; this contrasts with chemical erosion, where soil or rock material is removed from an area by its dissolving into a solvent (typically water), followed by the flow away of that solution. Eroded sediment or solutes may be transported just a few millimetres, or for thousands of kilometres.
Natural rates of erosion are controlled by the action of geomorphic drivers, such as rainfall; bedrock wear in rivers; coastal erosion by the sea and waves; glacial plucking, abrasion, and scour; areal flooding; wind abrasion; groundwater processes; and mass movement processes in steep landscapes like landslides and debris flows. The rates at which such processes act control how fast a surface is eroded. Typically, physical erosion proceeds fastest on steeply sloping surfaces, and rates may also be sensitive to some climatically-controlled properties including amounts of water supplied (e.g., by rain), storminess, wind speed, wave fetch, or atmospheric temperature (especially for some ice-related processes). Feedbacks are also possible between rates of erosion and the amount of eroded material that is already carried by, for example, a river or glacier. Processes of erosion that produce sediment or solutes from a place contrast with those of deposition, which control the arrival and emplacement of material at a new location.
While erosion is a natural process, human activities have increased by 10-40 times the rate at which erosion is occurring globally. At well-known agriculture sites such as the Appalachian Mountains, intensive farming practices have caused erosion up to 100x the speed of the natural rate of erosion in the region. Excessive (or accelerated) erosion causes both "on-site" and "off-site" problems. On-site impacts include decreases in agricultural productivity and (on natural landscapes) ecological collapse, both because of loss of the nutrient-rich upper soil layers. In some cases, the eventual end result is desertification. Off-site effects include sedimentation of waterways and eutrophication of water bodies, as well as sediment-related damage to roads and houses. Water and wind erosion are the two primary causes of land degradation; combined, they are responsible for about 84% of the global extent of degraded land, making excessive erosion one of the most significant environmental problems worldwide.:2:1
Intensive agriculture, deforestation, roads, anthropogenic climate change and urban sprawl are amongst the most significant human activities in regard to their effect on stimulating erosion. However, there are many prevention and remediation practices that can curtail or limit erosion of vulnerable soils.
- 1 Physical processes
- 2 Factors affecting erosion rates
- 3 Erosion of Earth systems
- 4 See also
- 5 References
- 6 Further reading
- 7 External links
Rainfall and surface runoff
Rainfall, and the surface runoff which may result from rainfall, produces four main types of soil erosion: splash erosion, sheet erosion, rill erosion, and gully erosion. Splash erosion is generally seen as the first and least severe stage in the soil erosion process, which is followed by sheet erosion, then rill erosion and finally gully erosion (the most severe of the four).:60–61
In splash erosion, the impact of a falling raindrop creates a small crater in the soil, ejecting soil particles. The distance these soil particles travel can be as much as 0.6 m (two feet) vertically and 1.5 m (five feet) horizontally on level ground.
If the soil is saturated, or if the rainfall rate is greater than the rate at which water can infiltrate into the soil, surface runoff occurs. If the runoff has sufficient flow energy, it will transport loosened soil particles (sediment) down the slope. Sheet erosion is the transport of loosened soil particles by overland flow.
Rill erosion refers to the development of small, ephemeral concentrated flow paths which function as both sediment source and sediment delivery systems for erosion on hillslopes. Generally, where water erosion rates on disturbed upland areas are greatest, rills are active. Flow depths in rills are typically of the order of a few centimetres (about an inch) or less and along-channel slopes may be quite steep. This means that rills exhibit hydraulic physics very different from water flowing through the deeper, wider channels of streams and rivers.
Rivers and streams
Valley or stream erosion occurs with continued water flow along a linear feature. The erosion is both downward, deepening the valley, and headward, extending the valley into the hillside, creating head cuts and steep banks. In the earliest stage of stream erosion, the erosive activity is dominantly vertical, the valleys have a typical V cross-section and the stream gradient is relatively steep. When some base level is reached, the erosive activity switches to lateral erosion, which widens the valley floor and creates a narrow floodplain. The stream gradient becomes nearly flat, and lateral deposition of sediments becomes important as the stream meanders across the valley floor. In all stages of stream erosion, by far the most erosion occurs during times of flood, when more and faster-moving water is available to carry a larger sediment load. In such processes, it is not the water alone that erodes: suspended abrasive particles, pebbles and boulders can also act erosively as they traverse a surface, in a process known as traction.
Bank erosion is the wearing away of the banks of a stream or river. This is distinguished from changes on the bed of the watercourse, which is referred to as scour. Erosion and changes in the form of river banks may be measured by inserting metal rods into the bank and marking the position of the bank surface along the rods at different times.
Thermal erosion is the result of melting and weakening permafrost due to moving water. It can occur both along rivers and at the coast. Rapid river channel migration observed in the Lena River of Siberia is due to thermal erosion, as these portions of the banks are composed of permafrost-cemented non-cohesive materials. Much of this erosion occurs as the weakened banks fail in large slumps. Thermal erosion also affects the Arctic coast, where wave action and near-shore temperatures combine to undercut permafrost bluffs along the shoreline and cause them to fail. Annual erosion rates along a 100-kilometre (62-mile) segment of the Beaufort Sea shoreline averaged 5.6 metres (18 feet) per year from 1955 to 2002.
Shoreline erosion, which occurs on both exposed and sheltered coasts, primarily occurs through the action of currents and waves but sea level (tidal) change can also play a role.
Hydraulic action takes place when air in a joint is suddenly compressed by a wave closing the entrance of the joint. This then cracks it. Wave pounding is when the sheer energy of the wave hitting the cliff or rock breaks pieces off. Abrasion or corrasion is caused by waves launching seaload at the cliff. It is the most effective and rapid form of shoreline erosion (not to be confused with corrosion). Corrosion is the dissolving of rock by carbonic acid in sea water. Limestone cliffs are particularly vulnerable to this kind of erosion. Attrition is where particles/seaload carried by the waves are worn down as they hit each other and the cliffs. This then makes the material easier to wash away. The material ends up as shingle and sand. Another significant source of erosion, particularly on carbonate coastlines, is the boring, scraping and grinding of organisms, a process termed bioerosion.
Sediment is transported along the coast in the direction of the prevailing current (longshore drift). When the upcurrent amount of sediment is less than the amount being carried away, erosion occurs. When the upcurrent amount of sediment is greater, sand or gravel banks will tend to form as a result of deposition. These banks may slowly migrate along the coast in the direction of the longshore drift, alternately protecting and exposing parts of the coastline. Where there is a bend in the coastline, quite often a buildup of eroded material occurs forming a long narrow bank (a spit). Armoured beaches and submerged offshore sandbanks may also protect parts of a coastline from erosion. Over the years, as the shoals gradually shift, the erosion may be redirected to attack different parts of the shore.
Chemical erosion is the loss of matter in a landscape in the form of solutes. Chemical erosion is usually calculated from the solutes found in streams. Anders Rapp pioneered the study of chemical erosion in his work about Kärkevagge published in 1960.
Glaciers erode predominantly by three different processes: abrasion/scouring, plucking, and ice thrusting. In an abrasion process, debris in the basal ice scrapes along the bed, polishing and gouging the underlying rocks, similar to sandpaper on wood. Scientists have shown that, in addition to the role of temperature played in valley-deepening, other glaciological processes, such as erosion also control cross-valley variations. In a homogeneous bedrock erosion pattern, curved channel cross section beneath the ice is created. Though the glacier continues to incise vertically, the shape of the channel beneath the ice eventually remain constant, reaching a U-shaped parabolic steady-state shape as we now see in glaciated valleys. Scientists also provide numerical estimate of the time required for the ultimate formation of a steady-shaped U-shaped valley - approximately 100,000 years. In a weak bedrock (containing material more erodible than the surrounding rocks) erosion pattern, on the contrary, the amount of overdeepening is limited because ice velocities and erosion rates are reduced.
Glaciers can also cause pieces of bedrock to crack off in the process of plucking. In ice thrusting, the glacier freezes to its bed, then as it surges forward, it moves large sheets of frozen sediment at the base along with the glacier. This method produced some of the many thousands of lake basins that dot the edge of the Canadian Shield. Differences in the height of mountain ranges are not only being the result tectonic forces, such as rock uplift, but also local climate variations. Scientists use global analysis of topography to show that glacial erosion controls the maximum height of mountains, as the relief between mountain peaks and the snow line are generally confined to altitudes less than 1500 m. The erosion caused by glaciers worldwide erodes mountains so effectively that the term glacial buzzsaw has become widely used, which describes the limiting effect of glaciers on the height of mountain ranges. As mountains grow higher, they generally allow for more glacial activity (especially in the accumulation zone above the glacial equilibrium line altitude), which causes increased rates of erosion of the mountain, decreasing mass faster than isostatic rebound can add to the mountain. This provides a good example of a negative feedback loop. Ongoing research is showing that while glaciers tend to decrease mountain size, in some areas, glaciers can actually reduce the rate of erosion, acting as a glacial armour. Ice can not only erode mountains, but also protect them from erosion. Depending on glacier regime, even steep alpine lands can be preserved through time with the help of ice. Scientists have proved this theory by sampling eight summits of northwestern Svalbard using Be10 and Al26, showing that northwestern Svalbard transformed from a glacier-erosion state under relatively mild glacial maxima temperature, to a glacier-armour state occupied by cold-based, protective ice during much colder glacial maxima temperatures as the Quaternary ice age progressed.
These processes, combined with erosion and transport by the water network beneath the glacier, leave moraines, drumlins, ground moraine (till), kames, kame deltas, moulins, and glacial erratics in their wake, typically at the terminus or during glacier retreat.
The best-developed glacial valley morphology appears to be restricted to landscapes with low rock uplift rates (less than or equal to 2 mm per year) and high relief, leading to long-turnover times. Where rock uplift rates exceed 2 mm per year, glacial valley morphology has generally been significantly modified in postglacial time. Interplay of glacial erosion and tectonic forcing governs the morphologic impact of glaciations on active orogens, by both influencing their height, and by altering the patterns of erosion during subsequent glacial periods via a link between rock uplift and valley cross-sectional shape.
At extremely high flows, kolks, or vortices are formed by large volumes of rapidly rushing water. Kolks cause extreme local erosion, plucking bedrock and creating pothole-type geographical features called Rock-cut basins. Examples can be seen in the flood regions result from glacial Lake Missoula, which created the channeled scablands in the Columbia Basin region of eastern Washington.
Wind erosion is a major geomorphological force, especially in arid and semi-arid regions. It is also a major source of land degradation, evaporation, desertification, harmful airborne dust, and crop damage—especially after being increased far above natural rates by human activities such as deforestation, urbanization, and agriculture.
Wind erosion is of two primary varieties: deflation, where the wind picks up and carries away loose particles; and abrasion, where surfaces are worn down as they are struck by airborne particles carried by wind. Deflation is divided into three categories: (1) surface creep, where larger, heavier particles slide or roll along the ground; (2) saltation, where particles are lifted a short height into the air, and bounce and saltate across the surface of the soil; and (3) suspension, where very small and light particles are lifted into the air by the wind, and are often carried for long distances. Saltation is responsible for the majority (50-70%) of wind erosion, followed by suspension (30-40%), and then surface creep (5-25%).:57
Wind erosion is much more severe in arid areas and during times of drought. For example, in the Great Plains, it is estimated that soil loss due to wind erosion can be as much as 6100 times greater in drought years than in wet years.
Mass movement is an important part of the erosional process, and is often the first stage in the breakdown and transport of weathered materials in mountainous areas.:93 It moves material from higher elevations to lower elevations where other eroding agents such as streams and glaciers can then pick up the material and move it to even lower elevations. Mass-movement processes are always occurring continuously on all slopes; some mass-movement processes act very slowly; others occur very suddenly, often with disastrous results. Any perceptible down-slope movement of rock or sediment is often referred to in general terms as a landslide. However, landslides can be classified in a much more detailed way that reflects the mechanisms responsible for the movement and the velocity at which the movement occurs. One of the visible topographical manifestations of a very slow form of such activity is a scree slope.
Slumping happens on steep hillsides, occurring along distinct fracture zones, often within materials like clay that, once released, may move quite rapidly downhill. They will often show a spoon-shaped isostatic depression, in which the material has begun to slide downhill. In some cases, the slump is caused by water beneath the slope weakening it. In many cases it is simply the result of poor engineering along highways where it is a regular occurrence.
Surface creep is the slow movement of soil and rock debris by gravity which is usually not perceptible except through extended observation. However, the term can also describe the rolling of dislodged soil particles 0.5 to 1.0 mm (0.02 to 0.04 in) in diameter by wind along the soil surface.
Factors affecting erosion rates
The amount and intensity of precipitation is the main climatic factor governing soil erosion by water. The relationship is particularly strong if heavy rainfall occurs at times when, or in locations where, the soil's surface is not well protected by vegetation. This might be during periods when agricultural activities leave the soil bare, or in semi-arid regions where vegetation is naturally sparse. Wind erosion requires strong winds, particularly during times of drought when vegetation is sparse and soil is dry (and so is more erodible). Other climatic factors such as average temperature and temperature range may also affect erosion, via their effects on vegetation and soil properties. In general, given similar vegetation and ecosystems, areas with more precipitation (especially high-intensity rainfall), more wind, or more storms are expected to have more erosion.
In some areas of the world (e.g. the mid-western USA), rainfall intensity is the primary determinant of erosivity (for a definition of erosivity check,) with higher intensity rainfall generally resulting in more soil erosion by water. The size and velocity of rain drops is also an important factor. Larger and higher-velocity rain drops have greater kinetic energy, and thus their impact will displace soil particles by larger distances than smaller, slower-moving rain drops.:29–31
In other regions of the world (e.g. western Europe), runoff and erosion result from relatively low intensities of stratiform rainfall falling onto previously saturated soil. In such situations, rainfall amount rather than intensity is the main factor determining the severity of soil erosion by water.
In Taiwan, where typhoon frequency increased significantly in the 21st century, a strong link has been drawn between the increase in storm frequency with an increase in sediment load in rivers and reservoirs, highlighting the impacts climate change can have on erosion.
Vegetation acts as an interface between the atmosphere and the soil. It increases the permeability of the soil to rainwater, thus decreasing runoff. It shelters the soil from winds, which results in decreased wind erosion, as well as advantageous changes in microclimate. The roots of the plants bind the soil together, and interweave with other roots, forming a more solid mass that is less susceptible to both water and wind erosion. The removal of vegetation increases the rate of surface erosion.
The topography of the land determines the velocity at which surface runoff will flow, which in turn determines the erosivity of the runoff. Longer, steeper slopes (especially those without adequate vegetative cover) are more susceptible to very high rates of erosion during heavy rains than shorter, less steep slopes. Steeper terrain is also more prone to mudslides, landslides, and other forms of gravitational erosion processes.:28–30
Tectonic processes control rates and distributions of erosion at the Earth's surface. If tectonic action causes part of the Earth's surface (e.g., a mountain range) to be raised or lowered relative to surrounding areas, this must necessarily change the gradient of the land surface. Because erosion rates are almost always sensitive to local slope (see above), this will change the rates of erosion in the uplifted area. Active tectonics also brings fresh, unweathered rock towards the surface, where it is exposed to the action of erosion.
However, erosion can also affect tectonic processes. The removal by erosion of large amounts of rock from a particular region, and its deposition elsewhere, can result in a lightening of the load on the lower crust and mantle. Because tectonic processes are driven by gradients in the stress field developed in the crust, this unloading can in turn cause tectonic or isostatic uplift in the region.:99 In some cases, it has been hypothesised that these twin feedbacks can act to localise and enhance zones of very rapid exhumation of deep crustal rocks beneath places on the Earth's surface with extremely high erosion rates, for example, beneath the extremely steep terrain of Nanga Parbat in the western Himalayas. Such a place has been called a "tectonic aneurysm".
Human land development, in forms including agricultural and urban development, is considered a significant factor in erosion and sediment transport. In Taiwan, increases in sediment load in the northern, central, and southern regions of the island can be tracked with the timeline of development for each region throughout the 20th century.
Erosion of Earth systems
|This section needs expansion. You can help by adding to it. (November 2015)|
Mountain ranges are known to take many millions of years to erode to the degree they effectively cease to exist. Scholars Pitman and Golovchenko estimate that it takes probably more than 450 million years to erode a mountain mass similar to the Himalaya into an almost-flat peneplain if there are no major sea-level changes. Erosion of mountains massifs can create a pattern of equally high summits called summit accordance. It has been argued that extension during post-orogenic collapse is a more effective mechanism of lowering the height of orogenic mountains than erosion.
Examples of heavily eroded mountain ranges include the Timanides of Northern Russia. Erosion of this orogen has produced sediments that are now found in the East European Platform, including the Cambrian Sablya Formation near Lake Ladoga. Studies of these sediments indicate that it is likely that the erosion of the orogen began in the Cambrian and then intensified in the Ordovician.
If the rate of erosion is higher than the rate of soil formation the soils are being destroyed by erosion. Where soil is not destroyed by erosion, erosion can in some cases prevent the formation of soil features that form slowly. Inceptisols are common soils that form in areas of fast erosion.
While erosion of soils is a natural process, human activities have increased by 10-40 times the rate at which erosion is occurring globally. Excessive (or accelerated) erosion causes both "on-site" and "off-site" problems. On-site impacts include decreases in agricultural productivity and (on natural landscapes) ecological collapse, both because of loss of the nutrient-rich upper soil layers. In some cases, the eventual end result is desertification. Off-site effects include sedimentation of waterways and eutrophication of water bodies, as well as sediment-related damage to roads and houses. Water and wind erosion are the two primary causes of land degradation; combined, they are responsible for about 84% of the global extent of degraded land, making excessive erosion one of the most significant environmental problems.
- Bridge scour
- Cellular confinement
- Coastal sediment supply
- Food security
- Groundwater sapping
- Highly erodible land
- Ice jacking
- Marine terrace
- Riparian strips
- River anticlines
- Sediment transport
- Space weathering
- Sphericity scale
- TERON (Tillage erosion)
- Vetiver System
- "Erosion". Encyclopædia Britannica. 2015-12-03.
- Cheraghi, M., S. Jomaa, G. C. Sander, and D. A. Barry (2016 ), Hysteretic sediment ﬂuxes in rainfall-driven soil erosion: Particle size effects, Water Resour. Res., 52, doi:10.1002/ 2016WR019314 file [http://onlinelibrary.wiley.com/doi/10.1002/2016WR019314/full link]
- Hallet, Bernard (1981). "Glacial Abrasion and Sliding: Their Dependence on the Debris Concentration In Basal Ice". Annals of Glaciology. 2 (1): 23–28. Bibcode:1981AnGla...2...23H. doi:10.3189/172756481794352487. ISSN 0260-3055.
- Sklar, Leonard S.; Dietrich, William E. (2004). "A mechanistic model for river incision into bedrock by saltating bed load" (PDF). Water Resources Research. 40 (6): W06301. Bibcode:2004WRR....40.6301S. doi:10.1029/2003WR002496. ISSN 0043-1397.
- Dotterweich, Markus (2013-11-01). "The history of human-induced soil erosion: Geomorphic legacies, early descriptions and research, and the development of soil conservation—A global synopsis". Geomorphology. 201: 1–34. doi:10.1016/j.geomorph.2013.07.021.
- Reusser, L.; Bierman, P.; Rood, D. "Quantifying human impacts on rates of erosion and sediment transport at a landscape scale". Geology. 43 (2): 171–174. doi:10.1130/g36272.1.
- Blanco-Canqui, Humberto; Rattan, Lal (2008). "Soil and water conservation". Principles of soil conservation and management. Dordrecht: Springer. pp. 1–20. ISBN 9781402087097.
- Toy, Terrence J.; Foster, George R.; Renard, Kenneth G. (2002). Soil erosion : processes, prediction, measurement, and control. New York, NY: Wiley. ISBN 9780471383697.
- Julien, Pierre Y. (2010). Erosion and Sedimentation. Cambridge University Press. p. 1. ISBN 978-0-521-53737-7.
- Zachar, Dušan (1982). "Classification of soil erosion". Soil Erosion. Vol. 10. Elsevier. p. 48. ISBN 978-0-444-99725-8.
- See Figure 1 in Obreschkow, D.; Dorsaz, N.; Kobel, P.; De Bosset, A.; Tinguely, M.; Field, J.; Farhat, M. (2011). "Confined Shocks inside Isolated Liquid Volumes - A New Path of Erosion?". Physics of Fluids. 23 (10): 101702. arXiv: . Bibcode:2011PhFl...23j1702O. doi:10.1063/1.3647583.
- Cheraghi, M., S. Jomaa, G. C. Sander, and D. A. Barry (2016 ), Hysteretic sediment ﬂuxes in rainfall-driven soil erosion: Particle size effects, Water Resour. Res., 52, doi:10.1002/ 2016WR019314
- Food and Agriculture Organization (1965). "Types of erosion damage". Soil Erosion by Water: Some Measures for Its Control on Cultivated Lands. United Nations. pp. 23–25. ISBN 978-92-5-100474-6.
- Nearing, M.A.; Norton, L.D.; Bulgakov, D.A.; Larionov, G.A.; West, L.T.; Dontsova, K.M. (1997). "Hydraulics and erosion in eroding rills". Water Resources Research. 33 (4): 865–876. Bibcode:1997WRR....33..865N. doi:10.1029/97wr00013.
- Boardman, John; Poesen, Jean, eds. (2007). Soil Erosion in Europe. Chichester: John Wiley & Sons. ISBN 9780470859117.
- J. Poesen, L. Vandekerckhove, J. Nachtergaele, D. Oostwoud Wijdenes, G. Verstraeten, B. Can Wesemael (2002). "Gully erosion in dryland environments". In Bull, Louise J. & Kirby, M.J. Dryland Rivers: Hydrology and Geomorphology of Semi-Arid Channels. John Wiley & Sons. pp. 229–262. ISBN 978-0-471-49123-1.
- Borah, Deva K. et al. (2008). "Watershed sediment yield". In Garcia, Marcelo H. Sedimentation Engineering: Processes, Measurements, Modeling, and Practice. ASCE Publishing. p. 828. ISBN 978-0-7844-0814-8.
- Ritter, Michael E. (2006) "Geologic Work of Streams" The Physical Environment: an Introduction to Physical Geography University of Wisconsin, OCLC 79006225
- Nancy D. Gordon (2004-06-01). "Erosion and Scour". Stream hydrology: an introduction for ecologists. ISBN 978-0-470-84357-4.
- "Thermal Erosion". NSIDC Glossary. National Snow and Ice Data Center. Archived from the original on 2010-11-19. Retrieved 21 December 2009.
- Costard, F.; Dupeyrat, L.; Gautier, E.; Carey-Gailhardis, E. (2003). "Fluvial thermal erosion investigations along a rapidly eroding river bank: application to the Lena River (central Siberia)". Earth Surface Processes and Landforms. 28 (12): 1349–1359. Bibcode:2003ESPL...28.1349C. doi:10.1002/esp.592.
- Jones, B.M.; Hinkel, K.M.; Arp, C.D.; Eisner, W.R. (2008). "Modern Erosion Rates and Loss of Coastal Features and Sites, Beaufort Sea Coastline, Alaska". Arctic. Arctic Institute of North America. 61 (4): 361–372. doi:10.14430/arctic44.
- Glynn, Peter W. "Bioerosion and coral-reef growth: a dynamic balance." Life and death of coral reefs (1997): 68-95.
- Dixon, John C.; Thorn, Colin E. (2005). "Chemical weathering and landscape development in mid-latitude alpine environments". Geomorphology. 67 (1–2): 127–145. Bibcode:2005Geomo..67..127D. doi:10.1016/j.geomorph.2004.07.009. Retrieved 22 November 2015.
- Harbor, Jonathan M.; Hallet, Bernard; Raymond, Charles F. (1988-05-26). "A numerical model of landform development by glacial erosion". Nature. 333 (6171): 347–349. doi:10.1038/333347a0.
- Egholm, D. L.; Nielsen, S. B.; Pedersen, V. K.; Lesemann, J.-E. "Glacial effects limiting mountain height". Nature. 460 (7257): 884–887. doi:10.1038/nature08263.
- Thomson, Stuart N.; Brandon, Mark T.; Tomkin, Jonathan H.; Reiners, Peter W.; Vásquez, Cristián; Wilson, Nathaniel J. (2010). "Glaciation as a destructive and constructive control on mountain building". Nature. 467 (7313): 313–317. Bibcode:2010Natur.467..313T. doi:10.1038/nature09365. PMID 20844534.
- Tomkin, J. H.; Roe, G. H. (2007). "Climate and tectonic controls on glaciated critical-taper orogens". Earth Planet. Sci. Lett. 262 (3–4): 385–397. Bibcode:2007E&PSL.262..385T. doi:10.1016/j.epsl.2007.07.040.
- Mitchell, S. G. & Montgomery, D. R. Influence of a glacial buzzsaw on the height and morphology of the Cascade Range in central Washington State, USA. Quat. Res. 65, 96–107 (2006)
- Gjermundsen, Endre F.; Briner, Jason P.; Akçar, Naki; Foros, Jørn; Kubik, Peter W.; Salvigsen, Otto; Hormes, Anne. "Minimal erosion of Arctic alpine topography during late Quaternary glaciation". Nature Geoscience. doi:10.1038/ngeo2524.
- Prasicek, Günther; Larsen, Isaac J.; Montgomery, David R. (2015-08-14). "Tectonic control on the persistence of glacially sculpted topography". Nature Communications. 6: 8028. doi:10.1038/ncomms9028. ISSN 2041-1723. PMC . PMID 26271245.
- See, for example: Alt, David (2001). Glacial Lake Missoula & its Humongous Floods. Mountain Press. ISBN 978-0-87842-415-3.
- Zheng, Xiaojing & Huang, Ning (2009). Mechanics of Wind-Blown Sand Movements. Springer. pp. 7–8. ISBN 978-3-540-88253-4.
- Cornelis, Wim S. (2006). "Hydroclimatology of wind erosion in arid and semi-arid environments". In D'Odorico, Paolo & Porporato, Amilcare. Dryland Ecohydrology. Springer. p. 141. ISBN 978-1-4020-4261-4.
- Blanco-Canqui, Humberto; Rattan, Lal (2008). "Wind erosion". Principles of soil conservation and management. Dordrecht: Springer. pp. 54–80. ISBN 9781402087097.
- Balba, A. Monem (1995). "Desertification: Wind erosion". Management of Problem Soils in Arid Ecosystems. CRC Press. p. 214. ISBN 978-0-87371-811-0.
- Wiggs, Giles F.S. (2011). "Geomorphological hazards in drylands". In Thomas, David S.G. Arid Zone Geomorphology: Process, Form and Change in Drylands. John Wiley & Sons. p. 588. ISBN 978-0-470-71076-0.
- Van Beek, Rens (2008). "Hillside processes: mass wasting, slope stability, and erosion". In Norris, Joanne E. et al. Slope Stability and Erosion Control: Ecotechnological Solutions. Springer. ISBN 978-1-4020-6675-7.
- Gray, Donald H. & Sotir, Robbin B. (1996). "Surficial erosion and mass movement". Biotechnical and Soil Bioengineering Slope Stabilization: A Practical Guide for Erosion Control. John Wiley & Sons. p. 20. ISBN 978-0-471-04978-4.
- Nichols, Gary (2009). Sedimentology and Stratigraphy. John Wiley & Sons. ISBN 978-1-4051-9379-5.
- "Britannica Library". library.eb.com. Retrieved 2017-01-31.
- Zorn, Matija; Komac, Blaž (2013-01-01). Bobrowsky, Peter T., ed. Encyclopedia of Natural Hazards. Encyclopedia of Earth Sciences Series. Springer Netherlands. pp. 289–290. doi:10.1007/978-1-4020-4399-4_121. ISBN 9789048186990.
- Blanco-Canqui, Humberto; Rattan, Lal (2008). "Water erosion". Principles of soil conservation and management. Dordrecht: Springer. pp. 21–53. ISBN 9781402087097.
- Montgomery, David R.; Huang, Michelle Y.-F.; Huang, Alice Y.-L. (2014-01-01). "Regional soil erosion in response to land use and increased typhoon frequency and intensity, Taiwan". Quaternary Research. 81 (1): 15–20. doi:10.1016/j.yqres.2013.10.005. ISSN 0033-5894.
- Gyssels, G.; Poesen, J.; Bochet, E.; Li, Y. (2005-06-01). "Impact of plant roots on the resistance of soils to erosion by water: a review". Progress in Physical Geography. 29 (2): 189–217. doi:10.1191/0309133305pp443ra. ISSN 0309-1333.
- Styczen, M.E. & Morgan, R.P.C. (1995). "Engineering properties of vegetation". In Morgan, R.P.C. & Rickson, R. Jane. Slope Stabilization and Erosion Control: A Bioengineering Approach. Taylor & Francis. ISBN 978-0-419-15630-7.
- Whisenant, Steve G. (2008). "Terrestrial systems". In Perrow Michael R. & Davy, Anthony J. Handbook of Ecological Restoration: Principles of Restoration. Cambridge University Press. p. 89. ISBN 978-0-521-04983-2.
- Wainwright, John & Brazier, Richard E. (2011). "Slope systems". In Thomas, David S.G. Arid Zone Geomorphology: Process, Form and Change in Drylands. John Wiley & Sons. ISBN 978-0-470-71076-0.
- Burbank, Douglas W.; Anderson, Robert S. (2011). "Tectonic and surface uplift rates". Tectonic Geomorphology. John Wiley & Sons. pp. 270–271. ISBN 978-1-4443-4504-9.
- Zeitler, P. K. et al. (2001), Erosion, Himalayan Geodynamics, and the Geomorphology of Metamorphism, GSA Today, 11, 4–9.
- Chen, Jie (2007-01-16). "Rapid urbanization in China: A real challenge to soil protection and food security". CATENA. Influences of rapid urbanization and industrialization on soil resource and its quality in China. 69 (1): 1–15. doi:10.1016/j.catena.2006.04.019.
- Pitman, W. C.; Golovchenko, X. (1991). "The effect of sea level changes on the morphology of mountain belts". Journal of Geophysical Research: Solid Earth. 96 (B4): 6879–6891. Bibcode:1991JGR....96.6879P. doi:10.1029/91JB00250. ISSN 0148-0227.
- Beckinsale, Robert P.; Chorley, Richard J. (2003) . "Chapter Seven: American Polycyclic Geomorphology". The History of the Study of Landforms. Volume Three. Taylor & Francis e-Library. pp. 235–236.
- Dewey, J.F.; Ryan, P.D.; Andersen, T.B. (1993). "Orogenic uplift and collapse, crustal thickness, fabrics and metamorphic phase changes: the role of eclogites". Geological Society, London, Special Publications. 76 (1): 325–343. doi:10.1144/gsl.sp.1993.076.01.16.
- Orlov, S.Yu.; Kuznetsov, N.B.; Miller, E.D.; Soboleva, A.A.; Udoratina, O.V. (2011). "Age Constraints for the Pre–Uralide–Timanide Orogenic Event Inferred from the Study of Detrital Zircons" (PDF). Doklady Earth Sciences. 440 (1): 1216–1221. Bibcode:2011DokES.440.1216O. doi:10.1134/s1028334x11090078. Retrieved 22 September 2015.
- Lupia-Palmieri, Elvidio (2004). "Erosion". In Goudie, A.S. Encyclopedia of Geomorphology. p. 336.
- Alexander, Earl B. (2014). Soils in natural landscapes. CRC Press. p. 108. ISBN 978-1-4665-9436-4.
- Blanco, Humberto & Lal, Rattan (2010). "Soil and water conservation". Principles of Soil Conservation and Management. Springer. p. 2. ISBN 978-90-481-8529-0.
- Boardman, John; Poesen, Jean, eds. (2007). Soil Erosion in Europe. Chichester: John Wiley & Sons. ISBN 9780470859117.
- Montgomery, David (October 2, 2008). Dirt: The Erosion of Civilizations (1st ed.). University of California Press. ISBN 978-0-520-25806-8.
- Montgomery, D. R. (8 August 2007). "Soil erosion and agricultural sustainability". Proceedings of the National Academy of Sciences. 104 (33): 13268–13272. Bibcode:2007PNAS..10413268M. doi:10.1073/pnas.0611508104.
- Vanoni, Vito A., ed. (1975-01-01). "The nature of sedimentation problems". Sedimentation Engineering. ASCE Publications. ISBN 978-0-7844-0823-0.
- Mainguet, Monique; Dumay, Frédéric (April 2011). Fighting wind erosion. One aspect of the combat against desertification. Les dossiers thématiques du CSFD. CSFD/Agropolis International. Retrieved 7 October 2015.