Tacoma Narrows Bridge (1940)
This article needs additional citations for verification. (May 2018) (Learn how and when to remove this template message)
|Tacoma Narrows Bridge|
The original Tacoma Narrows Bridge roadway twisted and vibrated violently under 40-mile-per-hour (64 km/h) winds on the day of the collapse
|Other name(s)||Galloping Gertie|
|Total length||5,939 feet (1,810.2 m)|
|Longest span||2,800 feet (853.4 m)|
|Clearance below||195 feet (59.4 m)|
|Opened||July 1, 1940|
|Collapsed||November 7, 1940|
The 1940 Tacoma Narrows Bridge, the first Tacoma Narrows Bridge, was a suspension bridge in the U.S. state of Washington that spanned the Tacoma Narrows strait of Puget Sound between Tacoma and the Kitsap Peninsula. It opened to traffic on July 1, 1940, and dramatically collapsed into Puget Sound on November 7 of the same year. At the time of its construction (and its destruction), the bridge was the third-longest suspension bridge in the world in terms of main span length, behind the Golden Gate Bridge and the George Washington Bridge.
Construction on the bridge began in September 1938. From the time the deck was built, it began to move vertically in windy conditions, which led to construction workers giving the bridge the nickname Galloping Gertie. The motion was observed even when the bridge opened to the public. Several measures aimed at stopping the motion were ineffective, and the bridge's main span finally collapsed under 40-mile-per-hour (64 km/h) wind conditions the morning of November 7, 1940.
Following the collapse, the United States' involvement in World War II delayed plans to replace the bridge. The portions of the bridge still standing after the collapse, including the towers and cables, were dismantled and sold as scrap metal. Nearly 10 years after the collapse, a new Tacoma Narrows Bridge opened in the same location, using the original bridge's tower pedestals and cable anchorages. The portion of the bridge that fell into the water now serves as an artificial reef.
The bridge's collapse had a lasting effect on science and engineering. In many physics textbooks, the event is presented as an example of elementary forced resonance; the bridge collapsed because normal speed winds produced aeroelastic flutter that matched the bridge's natural frequency. The collapse boosted research into bridge aerodynamics-aeroelastics, which has influenced the designs of all later long-span bridges.
- 1 Design and construction
- 2 Attempt to control structural vibration
- 3 Collapse
- 4 Inquiry
- 5 Link to the Armistice Day blizzard
- 6 Fate of the collapsed superstructure
- 7 Replacement bridge
- 8 See also
- 9 References
- 10 Further reading
- 11 External links
Design and construction
This section needs additional citations for verification. (April 2015) (Learn how and when to remove this template message)
The desire for the construction of a bridge between Tacoma and the Kitsap Peninsula dates back to 1889 with a Northern Pacific Railway proposal for a trestle, but concerted efforts began in the mid-1920s. The Tacoma Chamber of Commerce began campaigning and funding studies in 1923. Several noted bridge engineers, including Joseph B. Strauss, who went on to be chief engineer of the Golden Gate Bridge, and David B. Steinman, who went on to design the Mackinac Bridge, were consulted. Steinman made several Chamber-funded visits, culminating in a preliminary proposal presented in 1929, but by 1931, the Chamber decided to cancel the agreement on the grounds that Steinman was not sufficiently active in working to obtain financing. Another problem with financing the first bridge was buying out the ferry contract from a private firm running service on the Narrows at the time.
From the start, financing of the bridge was a problem: revenue from the proposed tolls would not be enough to cover construction costs, but there was strong support for the bridge from the U.S. Navy, which operated the Puget Sound Naval Shipyard in Bremerton, and from the U.S. Army, which ran McChord Field and Fort Lewis near Tacoma.
Washington State engineer Clark Eldridge produced a preliminary tried-and-true conventional suspension bridge design, and the Washington Toll Bridge Authority requested $11 million from the Federal Public Works Administration (PWA). Preliminary construction plans by the Washington Department of Highways had called for a set of 25-foot-deep (7.6 m) trusses to sit beneath the roadway and stiffen it.
However, according to Eldridge, "Eastern consulting engineers"—by which Eldridge meant Leon Moisseiff, the noted New York bridge engineer who served as designer and consultant engineer for the Golden Gate Bridge—petitioned the PWA and the Reconstruction Finance Corporation (RFC) to build the bridge for less. Moisseiff and Frederick Lienhard, the latter an engineer with what was then known as the Port of New York Authority, had published a paper that was probably the most important theoretical advance in the bridge engineering field of the decade. Their theory of elastic distribution extended the deflection theory that was originally devised by the Austrian engineer Josef Melan to horizontal bending under static wind load. They showed that the stiffness of the main cables (via the suspenders) would absorb up to one-half of the static wind pressure pushing a suspended structure laterally. This energy would then be transmitted to the anchorages and towers. Using this theory, Moisseiff argued for stiffening the bridge with a set of eight-foot-deep (2.4 m) plate girders rather than the 25 feet (7.6 m)-deep trusses proposed by the Washington Toll Bridge Authority. This approach meant a slimmer, more elegant design, and also reduced the construction costs as compared with the Highway Department's design proposed by Eldridge. Moisseiff's design won out, inasmuch as the other proposal was considered to be too expensive. On June 23, 1938, the PWA approved nearly $6 million for the Tacoma Narrows Bridge. Another $1.6 million was to be collected from tolls to cover the estimated total $8 million cost.
Following Moisseiff's design, bridge construction began on September 27, 1938. Construction took only nineteen months, at a cost of $6.4 million, which was financed by the grant from the PWA and a loan from the RFC. The Tacoma Narrows Bridge, with a main span of 2,800 feet (850 m), was the third-longest suspension bridge in the world at that time, following the George Washington Bridge between New Jersey and New York City, and the Golden Gate Bridge, connecting San Francisco with Marin County to its north.
Because planners expected fairly light traffic volumes, the bridge was designed with two lanes, and it was just 39 feet (12 m) wide. This was quite narrow, especially in comparison with its length. With only the 8-foot (2.4 m) deep plate girders providing additional depth, the bridge's roadway section was also shallow.
The decision to use such shallow and narrow girders proved to be the original Tacoma Narrows Bridge's undoing. With such minimal girders, the deck of the bridge was insufficiently rigid and was easily moved about by winds; from the start, the bridge became infamous for its movement. A mild to moderate wind could cause alternate halves of the center span to visibly rise and fall several feet over four- to five-second intervals. This flexibility was experienced by the builders and workmen during construction, which led some of the workers to christen the bridge "Galloping Gertie". The nickname soon stuck, and even the public (when the toll-paid traffic started) felt these motions on the day that the bridge opened on July 1, 1940.
Attempt to control structural vibration
- attachment of tie-down cables to the plate girders, which were anchored to 50-ton concrete blocks on the shore. This measure proved ineffective, as the cables snapped shortly after installation.
- addition of a pair of inclined cable stays that connected the main cables to the bridge deck at mid-span. These remained in place until the collapse, but were also ineffective at reducing the oscillations.
- finally, the structure was equipped with hydraulic buffers installed between the towers and the floor system of the deck to damp longitudinal motion of the main span. The effectiveness of the hydraulic dampers was nullified, however, because the seals of the units were damaged when the bridge was sand-blasted before being painted.
The Washington Toll Bridge Authority hired Professor Frederick Burt Farquharson, an engineering professor at the University of Washington, to make wind-tunnel tests and recommend solutions in order to reduce the oscillations of the bridge. Professor Farquharson and his students built a 1:200-scale model of the bridge and a 1:20-scale model of a section of the deck. The first studies concluded on November 2, 1940—five days before the bridge collapse on November 7. He proposed two solutions:
- To drill holes in the lateral girders and along the deck so that the air flow could circulate through them (in this way reducing lift forces).
- To give a more aerodynamic shape to the transverse section of the deck by adding fairings or deflector vanes along the deck, attached to the girder fascia.
The first option was not favored because of its irreversible nature. The second option was the chosen one, but it was not carried out, because the bridge collapsed five days after the studies were concluded.
Leonard Coatsworth, a Tacoma News Tribune editor, was the last person to drive on the bridge:
Around me I could hear concrete cracking. I started back to the car to get the dog, but was thrown before I could reach it. The car itself began to slide from side to side on the roadway. I decided the bridge was breaking up and my only hope was to get back to shore.
On hands and knees most of the time, I crawled 500 yards or more to the towers… My breath was coming in gasps; my knees were raw and bleeding, my hands bruised and swollen from gripping the concrete curb… Toward the last, I risked rising to my feet and running a few yards at a time… Safely back at the toll plaza, I saw the bridge in its final collapse and saw my car plunge into the Narrows.
Tubby, Coatsworth's cocker spaniel, was the only fatality of the Tacoma Narrows Bridge disaster; he was lost along with Coatsworth's car. Professor Farquharson and a news photographer attempted to rescue Tubby during a lull, but the dog was too terrified to leave the car and bit one of the rescuers. Tubby died when the bridge fell, and neither his body nor the car was ever recovered. Coatsworth had been driving Tubby back to his daughter, who owned the dog. Coatsworth received US$450.00 (US$7,900 with inflation) for his car and US$364.40 (US$6,400 with inflation) in reimbursement for the contents of his car, including Tubby.
Theodore von Kármán, the director of the Guggenheim Aeronautical Laboratory and a world-renowned aerodynamicist, was a member of the board of inquiry into the collapse. He reported that the State of Washington was unable to collect on one of the insurance policies for the bridge because its insurance agent had fraudulently pocketed the insurance premiums. The agent, Hallett R. French, who represented the Merchant's Fire Assurance Company, was charged and tried for grand larceny for withholding the premiums for $800,000 worth of insurance. The bridge, however, was insured by many other policies that covered 80% of the $5.2 million structure's value. Most of these were collected without incident.
Film of collapse
The collapse of the bridge was recorded on film by Barney Elliott, owner of a local camera shop. The film shows Leonard Coatsworth attempting to rescue his dog — without success — and then leaving the bridge. In 1998, The Tacoma Narrows Bridge Collapse was selected for preservation in the United States National Film Registry by the Library of Congress as being culturally, historically, or aesthetically significant. This footage is still shown to engineering, architecture, and physics students as a cautionary tale. Elliott's original films of the construction and collapse of the bridge were shot on 16 mm Kodachrome film, but most copies in circulation are in black and white because newsreels of the day copied the film onto 35 mm black-and-white stock. Most copies in circulation also show the bridge oscillating approximately 50% faster than real time, due to an assumption during conversion that the film was shot at 24 frames per second rather than the actual 16 fps.
Commission of the Federal Works Agency
A commission formed by the Federal Works Agency studied the collapse of the bridge. It included Othmar Ammann and Theodore von Kármán. Without drawing any definitive conclusions, the commission explored three possible failure causes:
- Aerodynamic instability by self-induced vibrations in the structure
- Eddy formations that might be periodic in nature
- Random effects of turbulence, that is the random fluctuations in velocity of the wind.
Cause of the collapse
This section does not cite any sources. (May 2018) (Learn how and when to remove this template message)
The original Tacoma Narrows Bridge was the first to be built with girders of carbon steel anchored in concrete blocks; preceding designs typically had open lattice beam trusses underneath the roadbed. This bridge was the first of its type to employ plate girders (pairs of deep I-beams) to support the roadbed. With the earlier designs, any wind would simply pass through the truss, but in the new design the wind would be diverted above and below the structure. Shortly after construction finished at the end of June (opened to traffic on July 1, 1940), it was discovered that the bridge would sway and buckle dangerously in relatively mild windy conditions that are common for the area, and worse during severe winds. This vibration was transverse, one-half of the central span rising while the other lowered. Drivers would see cars approaching from the other direction rise and fall, riding the violent energy wave through the bridge. However, at that time the mass of the bridge was considered to be sufficient to keep it structurally sound.
The failure of the bridge occurred when a never-before-seen twisting mode occurred, from winds at 40 miles per hour (64 km/h). This is a so-called torsional vibration mode (which is different from the transversal or longitudinal vibration mode), whereby when the left side of the roadway went down, the right side would rise, and vice versa (i.e., the two halves of the bridge twisted in opposite directions), with the center line of the road remaining still (motionless). Two men proved this point by walking along the center line, unaffected by the flapping of the roadway rising and falling to each side. This vibration was caused by aeroelastic fluttering.
Fluttering is a physical phenomenon in which several degrees of freedom of a structure become coupled in an unstable oscillation driven by the wind. Eventually, the amplitude of the motion produced by the fluttering increased beyond the strength of a vital part, in this case the suspender cables. Once several cables failed, the weight of the deck transferred to the adjacent cables that broke in turn until almost all of the central deck fell into the water below the span.
Resonance (due to Von Kármán vortex street) hypothesis
The bridge's spectacular destruction is often used as an object lesson in the necessity to consider both aerodynamics and resonance effects in civil and structural engineering. Billah and Scanlan (1991) reported that in fact, many physics textbooks (for example Resnick et al. and Tipler et al.) wrongly explain that the cause of the failure of the Tacoma Narrows bridge was externally forced mechanical resonance. Resonance is the tendency of a system to oscillate at larger amplitudes at certain frequencies, known as the system's natural frequencies. At these frequencies, even relatively small periodic driving forces can produce large amplitude vibrations, because the system stores energy. For example, a child using a swing realizes that if the pushes are properly timed, the swing can move with a very large amplitude. The driving force, in this case the child pushing the swing, exactly replenishes the energy that the system loses if its frequency equals the natural frequency of the system.
Usually, the approach taken by those physics textbooks is to introduce a first order forced oscillator, defined by the second-order differential equation
where m, c and k stand for the mass, damping coefficient and stiffness of the linear system and F and ω represent the amplitude and the angular frequency of the exciting force. The solution of such ordinary differential equation as a function of time t represents the displacement response of the system (given appropriate initial conditions). In the above system resonance happens when ω is approximately , i.e. is the natural (resonant) frequency of the system. The actual vibration analysis of a more complicated mechanical system—such as an airplane, a building or a bridge—is based on the linearization of the equation of motion for the system, which is a multidimensional version of equation (eq. 1). The analysis requires eigenvalue analysis and thereafter the natural frequencies of the structure are found, together with the so-called fundamental modes of the system, which are a set of independent displacements and/or rotations that specify completely the displaced or deformed position and orientation of the body or system, i.e., the bridge moves as a (linear) combination of those basic deformed positions.
Each structure has natural frequencies. For resonance to occur, it is necessary to have also periodicity in the excitation force. The most tempting candidate of the periodicity in the wind force was assumed to be the so-called vortex shedding. This is because bluff bodies (non-streamlined bodies), like bridge decks, in a fluid stream shed wakes, whose characteristics depend on the size and shape of the body and the properties of the fluid. These wakes are accompanied by alternating low-pressure vortices on the downwind side of the body (the so-called Von Kármán vortex street). The body will in consequence try to move toward the low-pressure zone, in an oscillating movement called vortex-induced vibration. Eventually, if the frequency of vortex shedding matches the natural frequency of the structure, the structure will begin to resonate and the structure's movement can become self-sustaining.
The frequency of the vortices in the von Kármán vortex street is called the Strouhal frequency , and is given by
Here, U stands for the flow velocity, D is a characteristic length of the bluff body and S is the dimensionless Strouhal number, which depends on the body in question. For Reynolds Numbers greater than 1000, the Strouhal number is approximately equal to 0.21. In the case of the Tacoma Narrows, D was approximately 8 feet (2.4 m) and S was 0.20.
It was thought that the Strouhal frequency was close enough to one of the natural vibration frequencies of the bridge i.e. , to cause resonance and therefore vortex-induced vibration.
In the case of the Tacoma Narrows Bridge, this appears not to have been the cause of the catastrophic damage. According to Professor Frederick Burt Farquharson, an engineering professor at the University of Washington and one of the main researchers into the cause of the bridge collapse, the wind was steady at 42 miles per hour (68 km/h) and the frequency of the destructive mode was 12 cycles/minute (0.2 Hz). This frequency was neither a natural mode of the isolated structure nor the frequency of blunt-body vortex shedding of the bridge at that wind speed (which was approximately 1 Hz). It can be concluded therefore that the vortex shedding was not the cause of the bridge collapse. The event can be understood only while considering the coupled aerodynamic and structural system that requires rigorous mathematical analysis to reveal all the degrees of freedom of the particular structure and the set of design loads imposed.
Note, however, that vortex-induced vibration is a far more complex process that involves both the external wind-initiated forces and internal self-excited forces that lock on to the motion of the structure. During lock-on, the wind forces drive the structure at or near one of its natural frequencies, but as the amplitude increases this has the effect of changing the local fluid boundary conditions, so that this induces compensating, self-limiting forces, which restrict the motion to relatively benign amplitudes. This is clearly not a linear resonance phenomenon, even if the bluff body has itself linear behaviour, since the exciting force amplitude is a nonlinear force of the structural response.
Resonance vs. non-resonance explanations
However, the Federal Works Administration report of the investigation (of which von Kármán was part) concluded that
It is very improbable that the resonance with alternating vortices plays an important role in the oscillations of suspension bridges. First, it was found that there is no sharp correlation between wind velocity and oscillation frequency such as is required in case of resonance with vortices whose frequency depends on the wind velocity.
A group of physicists cited "wind-driven amplification of the torsional oscillation" as distinct from resonance:
Subsequent authors have rejected the resonance explanation, and their perspective is gradually spreading to the physics community. The user's guide for the current American Association of Physics Teachers (AAPT) DVD states the bridge collapse "was not a case of resonance." Bernard Feldman likewise concluded in a 2003 article for the Physics Teacher that for the torsional oscillation mode, there was "no resonance behavior in the amplitude as a function of the wind velocity."
An important source for both the AAPT user's guide and for Feldman was a 1991 American Journal of Physics article by K. Yusuf Billah and Robert Scanlan. According to the two engineers, the failure of the bridge was related to a wind-driven amplification of the torsional oscillation that, unlike a resonance, increases monotonically with increasing wind speed. The fluid dynamics behind that amplification is complicated, but one key element, as described by physicists Daniel Green and William Unruh, is the creation of large-scale vortices above and below the roadway, or deck, of the bridge. Nowadays, bridges are constructed to be rigid and to have mechanisms that damp oscillations. Sometimes they include a slot in the middle of the deck to alleviate pressure differences above and below the road.
However, to some degree the debate is due to the lack of a commonly accepted precise definition of resonance. Billah and Scanlan provide the following definition of resonance "In general, whenever a system capable of oscillation is acted on by a periodic series of impulses having a frequency equal to or nearly equal to one of the natural frequencies of the oscillation of the system, the system is set into oscillation with a relatively large amplitude." They then state later in their paper "Could this be called a resonant phenomenon? It would appear not to contradict the qualitative definition of resonance quoted earlier, if we now identify the source of the periodic impulses as self-induced, the wind supplying the power, and the motion supplying the power-tapping mechanism. If one wishes to argue, however, that it was a case of externally forced linear resonance, the mathematical distinction ... is quite clear, self-exciting systems differing strongly enough from ordinary linear resonant ones."
Link to the Armistice Day blizzard
The strong winds in the Tacoma Narrows on 7 November 1940 were related to a remarkable low-pressure system that followed a track across the country and four days later produced the Armistice Day storm, one of the greatest storms ever to strike the Great Lakes region. For example, when the storm reached Illinois, the headline on the front page of the Chicago Tribune included the words "Heaviest winds in this century smash at city."
Additional details of the film and video analysis can be found in the November 2015 issue of the Physics Teacher, which also includes further description of the Armistice Day storm and the strong winds that earlier had caused the Tacoma Narrows Bridge to oscillate, twist, and collapse into the waters below.
Fate of the collapsed superstructure
Efforts to salvage the bridge began almost immediately after its collapse and continued into May 1943. Two review boards, one appointed by the federal government and one appointed by the state of Washington, concluded that repair of the bridge was impossible, and the entire bridge would have to be dismantled and an entirely new bridge superstructure built. With steel being a valuable commodity because of the involvement of the United States in World War II, steel from the bridge cables and the suspension span was sold as scrap metal to be melted down. The salvage operation cost the state more than was returned from the sale of the material, a net loss of over $350,000.
The cable anchorages, tower pedestals and most of the remaining substructure were relatively undamaged in the collapse, and were reused during construction of the replacement span that opened in 1950. The towers, which supported Gertie's main cables and road deck, suffered major damage at their bases from being deflected twelve feet towards shore as a result of the collapse of the mainspan and the sagging of the sidespans. They were dismantled, and the steel sent to recyclers.
Preservation of the collapsed roadway
The underwater remains of the highway deck of the old suspension bridge act as a large artificial reef, and these are listed on the National Register of Historic Places with reference number 92001068.
The Harbor History Museum has a display in their main gallery regarding the 1940 bridge, its collapse, and the subsequent two bridges.
A lesson for history
Othmar Ammann, a leading bridge designer and member of the Federal Works Agency Commission investigating the collapse of the Tacoma Narrows Bridge, wrote:
The Tacoma Narrows bridge failure has given us invaluable information… It has shown [that] every new structure [that] projects into new fields of magnitude involves new problems for the solution of which neither theory nor practical experience furnish an adequate guide. It is then that we must rely largely on judgment and if, as a result, errors, or failures occur, we must accept them as a price for human progress.
The Bronx Whitestone Bridge, which is of similar design to the 1940 Tacoma Narrows Bridge, was reinforced shortly after the collapse. Fourteen-foot-high (4.3 m) steel trusses were installed on both sides of the deck in 1943 to weigh down and stiffen the bridge in an effort to reduce oscillation. In 2003, the stiffening trusses were removed and aerodynamic fiberglass fairings were installed along both sides of the road deck.
A key consequence was that suspension bridges reverted to a deeper and heavier truss design, including the replacement Tacoma Narrows Bridge (1950), until the development in the 1960s of box girder bridges with an aerofoil shape such as the Severn Bridge, which gave the necessary stiffness together with reduced torsional forces.
Because of materials and labor shortages as a result of the involvement of the United States in World War II, it took 10 years before a replacement bridge was opened to traffic. This replacement bridge was opened to traffic on October 14, 1950, and is 5,979 feet (1,822 m) long—40 feet (12 m) longer than the original bridge. The replacement bridge also has more lanes than the original bridge, which only had two traffic lanes, plus shoulders on both sides.
Half a century later, the replacement bridge exceeded its traffic capacity, and a second, parallel suspension bridge was constructed to carry eastbound traffic. The suspension bridge that was completed in 1950 was reconfigured to carry only westbound traffic. The new parallel bridge opened to traffic in July 2007.
- List of bridge disasters
- List of structural failures and collapses
- Engineering disasters
- Volgograd Bridge, a bridge in Russia which experienced similar problems with the wind
- Billah, K.; R. Scanlan (1991). "Resonance, Tacoma Narrows Bridge Failure, and Undergraduate Physics Textbooks" (PDF). American Journal of Physics. 59 (2): 118–124. Bibcode:1991AmJPh..59..118B. doi:10.1119/1.16590.
- Petroski, Henry (2009). "Tacoma Narrows Bridges". American Scientist (2 ed.). 97: 103–107. ISSN 0003-0996.
- Plaut, R.H. (2008). "Snap Loads and Torsional Oscillation of the original Tacoma Narrows Bridge". Journal of Sound and Vibration. doi: 10.1016/j.jsv.2007.07.057
- Leon S. Moisseiff and Frederick Lienhard. "Suspension Bridges Under the Action of Lateral Forces," with discussion. Transactions of the American Society of Civil Engineers, No. 98, 1933, pp. 1080–1095, 1096–1141
- Richard Scott. In the Wake of Tacoma: Suspension Bridges and the Quest for Aerodynamic Stability. American Society of Civil Engineers (June 1, 2001) ISBN 0-7844-0542-5 https://books.google.com/books?id=DnQOzYDJsm8C
- Henry Petroski. Engineers of Dreams: Great Bridge Builders and the Spanning of America. New York: Knopf/Random House, 1995.
- Rita Robison. "Tacoma Narrows Bridge Collapse." In When Technology Fails, edited by Neil Schlager, pp. 18–190. Detroit: Gale Research, 1994.
- "Eyewitness accounts". Tacoma Narrows Bridge history. WDOT.
- "Professor's Analysis". Tacoma Narrows Bridge History. WDOT.
- As told by Clarence C. Murton, head of the Seattle Post Intelligencer Art Dept at the time, and close colleague of the photographer.
- "Tubby Trivia". Tacoma Narrows Bridge History. Washington State Department of Transportation.
- Federal Reserve Bank of Minneapolis Community Development Project. "Consumer Price Index (estimate) 1800–". Federal Reserve Bank of Minneapolis. Retrieved January 2, 2018.
- "Tacoma Narrows Bridge: Weird Facts". Washington State Department of Transportation.
Finally, the WSTBA reimbursed Coatsworth for the loss of his car, $450.00. They had already paid him $364.40 for the loss of his car's "contents".
- Halacy Jr., D. S. (1965). Father of Supersonic Flight: Theodor von Kármán. pp. 119–122.
- "Prison Minimum Set For Ex-Insurance Executive". The News-Review. Roseburg, Oregon. 22 May 1941. p. 1. Retrieved 13 January 2017 – via Newspapers.com.
- "Tacoma Narrows Bridge". University of Washington Special Collections. Retrieved 2006-11-13.
- "Weird Facts". Tacoma Narrows Bridge History. Washington State Department of Transportation.
The effects of Galloping Gertie's fall lasted long after the catastrophe. Clark Eldridge, who accepted some of the blame for the bridge's failure, learned this first-hand. In late 1941, Eldridge was working for the U.S. Navy on Guam when the United States entered World War II. Soon, the Japanese captured Eldridge. He spent the remainder of the war (three years and nine months) in a prisoner of war camp in Japan. To his amazement, one day a Japanese officer, who had once been a student in America, recognized the bridge engineer. He walked up to Eldridge and said bluntly, 'Tacoma Bridge!'
- "A Tacoma Narrows 'Galloping Gertie' bridge-collapse surprise, 75 years later". Seattle Post-Intelligencer. 7 November 2015. Retrieved 11 November 2015.
By timing the torsional oscillations, the Texas State researchers determined the bridge goes through 18 twisting cycles per minute on the existing video. Stopwatch measurements taken on November 7, 1940, however, timed the bridge cycles at 12 per minute--a significant discrepancy. The Texas State researchers were able to prove that the original 16 mm camera that filmed the oscillations was running at the slower 16 fps, not the 24 fps assumed when the conversion to video was done. When the film frames are viewed at the slower speed, the torsional cycles match the eyewitness stopwatch measurement of 12 cycles per minute.
- "Big Tacoma Bridge Crashes 190 Feet into Puget Sound. Narrows Span, Third Longest of Type in World, Collapses in Wind. Four Escape Death". New York Times. November 8, 1940.
Cracking in a forty-two-mile an hour wind, the $6,400,000 Tacoma narrows Bridge collapsed with a roar today and plunged into the waters of Puget Sound, 190 feet below.
- Halliday, David; Resnick, Robert; Walker, Jearl (2008). Fundamentals of Physics, (Chapters 21-44). John Wiley & Sons. ISBN 978-0-470-04474-2.
- Tipler, Paul Allen; Mosca, Gene (2004). Physics for Scientists and Engineers : Volume 1B: Oscillations and Waves; Thermodynamics (Physics for Scientists and Engineers). W. H. Freeman. ISBN 978-0-7167-0903-9.)
- F. B. Farquharson et al. Aerodynamic stability of suspension bridges with special reference to the Tacoma Narrows Bridge. University of Washington Engineering Experimental Station, Seattle. Bulletin 116. Parts I to V. A series of reports issued since June 1949 to June 1954.
- Billah, K.Y.R. and Scanlan, R. H. "Vortex-Induced Vibration and its Mathematical Modeling: A Bibliography", Report No.SM-89-1. Department of Civil Engineering. Princeton University. April 1989
- Theodore von Karman with Lee Edson. The wind and Beyond.Theodore von Karman: Pioneer in Aviation and Pathfinder in Space. Little Brown and Company, Boston, 1963. Page 213
- Steven Ross, et al. "Tacoma Narrows 1940." In Construction Disasters: Design Failures, Causes, and Prevention. McGraw Hill, 1984, pp. 216–239,.
- Olson, Donald W.; Wolf, Steven F.; Hook, Joseph M. (2015-11-01). "The Tacoma Narrows Bridge collapse". Physics Today. 68 (11): 64–65. Bibcode:2015PhT....68k..64O. doi:10.1063/PT.3.2991. ISSN 0031-9228.
- "Tacoma Narrows Bridge: Aftermath – A New Beginning: 1940 – 1950". www.wsdot.wa.gov.
- "Subject Guides & Online Exhibits — UW Libraries". www.lib.washington.edu.
- National Park Service (2007-01-23). "National Register Information System". National Register of Historic Places. National Park Service.
- "WSDOT - Tacoma Narrows Bridge: Extreme History". Washington State Department of Transportation. Retrieved 2007-10-23.
- Othmar H. Ammann, Theodore von Kármán and Glenn B. Woodruff. The Failure of the Tacoma Narrows Bridge, a report to the administrator. Report to the Federal Works Agency, Washington, 1941
- History.com Editors (August 21, 2018). "Tacoma Bridge collapses". HISTORY. A&E Television Networks. Retrieved November 7, 2018.
After the Tacoma Narrows disaster, bridge builders took care to incorporate aerodynamics into their designs and build structures with complex frequencies. Wind-tunnel testing of bridge designs eventually became mandatory.
- "The Strangest, Most Spectacular Bridge Collapse (And How We Got It Wrong)" (December 2015). A detailed, in-depth investigative report on the complicated physics behind the collapse in layman's terms, with videos, charts, graphs, diagrams etc. By Alex Pasternack, Motherboard
- Physics behind the collapse of the bridge
- failurebydesign.info – physics presentation and resources
- Sudden lateral asymmetry and torsional oscillations in the original Tacoma suspension bridge, Joseph Malik, Journal of Sound and Vibration, Vol 332, Issue 15, 22 July 2013, p. 3772–3789. Full article behind paywall, abstract freely viewable.
|Wikimedia Commons has media related to Tacoma Narrows Bridge (1940).|
- Color video of the original bridge's construction and collapse with narration
- Photos of the bridge and the new span under construction
- Tacoma Narrows Bridge (1940) at Structurae
- 1940 Narrows Bridge (1940 bridge construction) Washington State Department of Transportation
- History of the Tacoma Narrows Bridge
- University of Washington Libraries Digital Collection – Tacoma Narrows Bridge Collection More than 152 images and text documenting the infamous collapse in 1940 of the Tacoma Narrows Bridge. Also covers Galloping Gertie's creation, subsequent studies involving its aerodynamics, and finally the construction of a second bridge spanning the Narrows.
- The Tacoma Narrows Bridge Disaster, November 1940
- Images of failure
- Information and images of failure
- Official site of the Tacoma Narrows Bridge
- Timeline of the bridges
- Tacoma Narrows Bridge
- Suspended Animation – Failure Magazine (November 2000)
- A film clip of the Tacoma Narrows bridge wobbling and eventually, collapsing is available at the Internet Archive
- Youtube video of similar deck oscillations on a new bridge at Volgograd in Russia