Backflow prevention device

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Andy Dingley (talk | contribs) at 10:17, 10 February 2014 (Reverted 1 edit by BackflowPro (talk): Rv EL - over-promotional, adds nothing to this article. (TW)). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

In this situation, dirty water from the hillside pool will back-siphon or back-flow down the hosepipe and into the clean water tank. To prevent this from happening, the house's external tap should be fitted with a backflow prevention device.

A backflow prevention assembly is used to protect potable water supplies from contamination or pollution due to backflow.

In water supply systems, water is normally maintained at a significant pressure to enable water to flow from the tap, shower etc. When pressure fails or is reduced, as may happen if a water main bursts, pipes freeze or there is unexpectedly high demand on the water system, then such reduced pressure in the pipe may allow contaminated water from the ground, from storage or from other sources to be drawn up into the system.

Terminology

Points at which a potable water system connects with a non-potable water system, are called cross connections.

Backflow means the undesirable reversal of flow of a liquid, gas or solid into the potable water supply — A backflow preventer keeps this from happening.

Back-siphonage occurs when higher pressure fluids, gases, or suspended solids move to an area of lower pressure fluids. For example, using a straw to drink a beverage; the suction of drink will make the pressure of fluid inside the straw lower, thus, liquid will move from the cup to inside the straw and then up to your mouth. This is an example of an indirect cross-connection — undesirable material is being pulled into the system.

If instead, air is blown through the straw and bubbles begin to erupt at the submerged end, this is an example of back-pressure. If instead of air, natural gas had been forced into a potable water tank, it in turn could be carried to your kitchen faucet. This is an example of a direct cross-connection — undesirable material is being pushed into the system.

Back pressure can force an undesirable contaminant to enter potable water piping. Sources of back pressure may be pumps in the water distribution system, boilers, heat exchanging equipment, or power washing equipment. In these cases there may be an almost constant risk of overcoming the static water pressure in the piping. To reduce the risk of contamination, a backflow preventer can be fitted. A backflow preventer is also important when potentially toxic chemicals are used, for instance for commercial/industrial descaling (boilers) or when bleaches are used for residential power washing.

Preventive devices

The simplest, and a very effective way to provide backflow prevention, is to provide an air gap. An air gap is simply an open space between any device that connects to a plumbing system (like a valve or faucet) and any place where water can collect or pool.

Alternatively, a specialized backflow preventer valve may be installed at strategic locations in the plumbing system wherever there is a risk of contaminated fluids entering the water supply pipes.

Regulatory requirements

To prevent contamination due to back pressure, many health regulatory regimes require an air gap or mechanical backflow prevention assembly between the delivery point of mains water and local storage or use.[1] Where submerged mains inflow is permitted,[further explanation needed] a backflow prevention assembly is required, which protects the potable water system from contamination hazards.[citation needed] A check valve is a common form of backflow prevention, but more complex devices may instead be required.[further explanation needed]

In many countries. approved backflow prevention assemblies are required by law, and must be installed in accordance with plumbing or building codes.[example needed] A typical backflow assembly has test cocks and shut-off valves, and must be tested when installed, if relocated or repaired, and also on a periodic basis.[citation needed]

In the US, the Environmental Protection Agency (EPA) holds local water suppliers responsible for maintaining a certain amount of purity in potable water systems. Many states and/or local municipalities require annual testing of backflow prevention assemblies. In most cases, the law requires a double check (DC), Reduced Pressure Principle Device (RP) device, or an air gap when backflow prevention is mandated.[citation needed]

Partial list of backflow prevention devices

See also

Backflow (plumbing)

References

  1. ^ "The Water Supply (Water Fittings) Regulations 1999". Archived from the original on 23 August 2010. Retrieved July 26, 2010. {{cite web}}: Unknown parameter |deadurl= ignored (|url-status= suggested) (help)

External links

Retrieved from "https://en.wikipedia.org/w/index.php?title=Backflow_prevention_device&oldid=594803815"