Jump to content

Synchro-Cyclotron (CERN)

Coordinates: 46°13′58.7136″N 6°03′9.9468″E / 46.232976000°N 6.052763000°E / 46.232976000; 6.052763000
From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Citation bot (talk | contribs) at 02:39, 14 June 2022 (Add: title. Changed bare reference to CS1/2. | Use this bot. Report bugs. | Suggested by BrownHairedGirl | #UCB_webform 3512/3827). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

This article is about the specific machine at CERN. For the general concept, see Synchrocyclotron.
The Synchrocyclotron (SC)

The Synchro-Cyclotron, or Synchrocyclotron (SC), built in 1957, was CERN’s first accelerator. It was 15.7 metres (52 ft) in circumference and provided beams for CERN's first experiments in particle and nuclear physics. It accelerated particles to energies up to 600 MeV. The foundation stone of CERN was laid at the site of the Synchrocyclotron by the first Director-General of CERN, Felix Bloch.[1] After its remarkably long 33 years of service time, the SC was decommissioned in 1990. Nowadays it accepts visitors as an exhibition area in CERN.

Background

A Synchrocyclotron (as a general idea) was invented by Edwin McMillan in 1945. Its main purpose is to accelerate charged particles like protons and deutrons. The machine consists of two D shaped hollow metal electrodes (called "dee"s) with a gap between them, connected to a radio frequency (RF) alternating voltage source. These dees are placed on a plane in a way that their openings on the flat sides look at each other. The particles inside the Syncrocylotron can be accelerated from one dee to the other by the force produced by the electrical field between dees. The particles accelerated between dees with this method are rotated by the magnetic field created by two large magnets placed below and above the structure. The machine continues to accelerate particles by alternating the direction of the electrical field until they reach the maximum radius and then extracts them via a beam tube and sends them towards a target or another machine. Throughout the process, the frequency is being decreased to compensate relativistic mass increase due to the speed of the particles approaching the speed of light.

History

In late 1951, a UNESCO meeting about a new European organization for nuclear research was held in Paris. In the meeting, the synchrocyclotron machine was proposed as an ideal solution for a medium-energy accelerator to use until they built a more powerful accelerator. Later in May 1952, in the first council meeting of the proposed organization, Cornelis Bakker was appointed as director of the Synchro-Cyclotron Study Group.[2] After a month, in a report called Provisional Program of Synchro-Cyclotron Study Group, the group decided that they would need a design that could provide 600 MeV protons. The initial objective of the group stated as indicating the scope of the work to be done and studying and/or designing the necessary items. After preliminary studies, the first meeting of the SC study group was held in Copenhagen in mid-June. Decisions made in the meeting included several trips to see similar machines around the world, making contacts to find appropriate companies that can build necessary pieces and preparing basic drawings of the machine. After a second meeting at Amsterdam in August, a progress report dated 1 October 1952 was prepared to be presented in the meeting of the European Council for Nuclear Research which was going to be held in Amsterdam in October. According to the report, the group aimed to finish its work in a year and a complete report to be presented to the European Council for Nuclear Research. A preliminary design drawing of the SC was attached to the report which stated that the work of the group was progressing "satisfactorily" and they were cooperating "adequately".[2]

The Synchro-Cyclotron (CERN) construction site

In 1953, after a year of research, meetings and reports alike, the design of the Synchro-Cyclotron started. The construction of the machine began in 1954 on the site at Meyrin with the parts coming from all over Western Europe. In late 1955, Wolfgang Gentner became the director of the Synchro-Cyclotron Study Group, as former director Cornelis Bakker became the Director-General of CERN.[3] The research program for the Synchrocyclotron started to be planned to be able to start experiments as soon as possible.[4] The SC was ready to produce its first beam in August 1957, practically on the date foreseen. A press release by CERN on 16 August 1957, stated that the SC, as the third-largest accelerator of its type in the world, had started to work at its full energy.[5] In late 1958, the Synchrocyclotron made its first important contribution to nuclear physics by the discovery of the rare electron decay of the pion particle. This discovery helped theorists a lot by proving that this decay really occurs.[6] The Synchrocyclotron was used for an average of 135 hours per week during 1961; it ran continuously every day of the week except Mondays which were reserved for maintenance. The Synchrocyclotron was accelerating a jet of protons 54 times a second, up to a speed of approximately 240,000 kilometers per second (80% percent of the speed of light).[7]

In May 1960, plans for an isotope separator were published in Vienna. This isotope separator was built by CERN's Nuclear Chemistry Group (NCG) and used in measurements of production rates of radionuclides produced in the Synchrocyclotron. High production rates observed during these measurements proved that the SC was the ideal machine for experiments for on-line production of rare isotopes.[8] In April 1963, a group of physicists met at CERN to discuss for the isotope separator project. In late 1964, a formal proposal was submitted for the project and accepted by the CERN Director-General.[9] In the same year, the Synchrocyclotron started to concentrate on nuclear physics alone, leaving particle physics to a more powerful accelerator built in 1959, the Proton Synchrotron. In May 1966, the Synchrocyclotron was shut down for major modifications. Until mid-July, the capacity of the SC and its associated facilities were improved. Also, a new tunnel was constructed for an external proton beamline to the new underground hall for the new isotope separator.[10] In 1967, it started supplying beams for the dedicated radioactive-ion-beam facility called ISOLDE, which still carries out research ranging from pure nuclear physics to astrophysics and medical physics.

In 1969, preparations started to increase the beam intensity and improve the beam extraction efficiency of the SC. It was shut down in June 1973 for modifications. The highly improved machine started working again for physical research with its new name, SC2, in January 1975.[11] In 1990, ISOLDE was transferred to the Proton Synchrotron Booster, and the SC finally closed down after 33 years of service.[12]

Having served as storage facility since the 1990 shutdown, the SC and its building, the SC hall, were renovated in 2012-2013[13] to become an exhibition area for visitors, opening September 2013.[14] The exhibition includes a video about the birth of CERN and the Synchrocyclotron. Using projection mapping technology, it displays simulations of the accelerating particles on the SC and demonstrates parts of it. Some objects and tools which were used at the time the Synchrocyclotron was started are also in the hall for visitors to see.[15]

Activities

Below is the list of some physics activities done at the SC.[16][17][18]

References

  1. ^ Rubbia, Carlo (1993). "Opening address". Physics Reports. 225 (1–3): 12–25. Bibcode:1993PhR...225...12R. doi:10.1016/0370-1573(93)90155-7. ISSN 0370-1573.
  2. ^ a b Synchro-Cyclotron Divisional Reports, CERN-ARCH-Series, CERN, 1952, retrieved 17 July 2019
  3. ^ Hermann, Armin; Krige, Gerhard John; Mersits, Ulrike; Pestre, Dominique; Weiss, Laura (1990). History of CERN Volume II: Building and Running the Laboratory. Amsterdam: North-Holland. p. 106. ISBN 0444882073. Retrieved 13 August 2019.
  4. ^ Preparation For Experimentation With The SC Machine (PDF), CERN Scientific Policy Committee, 11 November 1955, retrieved 18 July 2019
  5. ^ CERN Synchro-cyclotron working at full energy (Press Release) (PDF), CERN, 16 August 1958, retrieved 19 July 2019
  6. ^ Crucial Experiment With CERN 600 MeV Synchro-Cyclotron (Press Release) (PDF), CERN, 11 September 1958, retrieved 19 July 2019
  7. ^ Press Release (PDF), CERN, 25 January 1962, retrieved 19 July 2019
  8. ^ "Plans for an isotope separator are published". CERN Timelines. CERN. Retrieved 8 July 2019.
  9. ^ "CERN approves the online separator project". CERN Timelines. CERN. Retrieved 9 July 2019.
  10. ^ "Synchrocyclotron shuts down". CERN Timelines. CERN. Retrieved 9 July 2019.
  11. ^ "Archives of Synchro-Cyclotron Division, SC". CERN Scientific Information Service. CERN. Retrieved 30 July 2019.
  12. ^ "The Sychrocyclotron". CERN. Retrieved 2014-10-10.
  13. ^ "The Synchrocyclotron prepares for visitors".
  14. ^ "Our universe was yours". 21 October 2013.
  15. ^ "Synchrocyclotron". Visit CERN. CERN. Retrieved 8 July 2019.
  16. ^ "(Full Issue)". Physics Reports. 225 (1–3): 1–191. April 1993. Retrieved 8 August 2019.
  17. ^ "Last Month at CERN". CERN Courier. 2 (9): 2. September 1962. Retrieved 8 August 2019.
  18. ^ Hermann, Armin; Krige, Gerhard John; Mersits, Ulrike; Pestre, Dominique; Weiss, Laura (1990). History of CERN Volume II: Building and Running the Laboratory. Amsterdam: North-Holland. p. 330. ISBN 0444882073. Retrieved 13 August 2019.

Further reading

46°13′58.7136″N 6°03′9.9468″E / 46.232976000°N 6.052763000°E / 46.232976000; 6.052763000

Retrieved from "https://en.wikipedia.org/w/index.php?title=Synchro-Cyclotron_(CERN)&oldid=1093024462"