7×64mm

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Alan Liefting (talk | contribs) at 23:26, 5 August 2009 (remove Category:Hunting using AWB). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

7x64mm
7x64mm (far left) amongst other rifle cartridges
TypeRifle
Place of origin Germany
Service history
In serviceNever issued
Production history
DesignerWilhelm Brenneke
Designed1917
Produced1917 - present
Variants7x65mm R (rimmed)
Specifications
Parent case8x64mm S
Case typeRimless, bottleneck
Bullet diameter7.24 mm (0.285 in)
Neck diameter7.95 mm (0.313 in)
Shoulder diameter10.80 mm (0.425 in)
Base diameter11.85 mm (0.467 in)
Rim diameter11.95 mm (0.470 in)
Rim thickness1.30 mm (0.051 in)
Case length64.00 mm (2.520 in)
Overall length84.00 mm (3.307 in)
Case capacity4.48 cm3 (69.1 gr H2O)
Rifling twist220 mm (1-8.66")
Primer typeLarge rifle
Maximum pressure415 MPa (60,200 psi)
Ballistic performance
Bullet mass/type Velocity Energy
8.0 g (123 gr) SP 910 m/s (3,000 ft/s) 3,810 J (2,810 ft⋅lbf)
10.0 g (154 gr) SP 880 m/s (2,900 ft/s) 3,901 J (2,877 ft⋅lbf)
11.3 g (174 gr) SP 820 m/s (2,700 ft/s) 3,841 J (2,833 ft⋅lbf)
Source(s): "Cartridges of the World" [1]

The 7x64mm (also unofficially known as the 7x64mm Brenneke, though its designers name officially never was added as a part of this cartridge name) is a rimless bottlenecked centerfire cartridge developed for hunting. As is customary in European cartridges the 7 denotes the 7 mm bullet caliber and the 64 denotes the 64 mm (2.52 in) case length. The 7x64mm is a popular hunting cartridge in central Europe and can due to its 84 mm (3.307 in) overall length easily be chambered in standard sized Mauser 98 bolt action rifles.

History

At the start of the 20th century the famous German gun and ammunition designer Wilhelm Brenneke (1865–1951) was lengthening standard cartridge cases like the M/88 cartridge case, then used by the German military in their Mauser 98 rifles, to obtain extra muzzle velocity.

In 1912 Brenneke designed the commercially rather unsuccessful 8x64mm S cartridge. It was intended as a ballistic upgrade option for the Mauser Gewehr 98 rifles that were then standard issue in the German military. The German military chose however to stick to their 8x57mm IS rifle cartridge avoiding rechambering their service rifles for a cartridge that due to its more favourable bore area to case volume ratio ballistically would outperform the .30-06 Springfield cartridge of the United States Army. Brenneke’s engineering concept to lengthen the 57 mm (2.244 in) long M/88 cartridge case to create new for those days very powerful cartridges was essentially sound and he persisted in the development of new cartridges along this line.

In 1917 Brenneke necked down his 8x64mm S design of 1912 to 7 mm calibre and introduced it as 7x64mm and achieved a major commercial success. The 7x64mm offered compared to the 7x57mm about 10 to 12 % extra muzzle velocity. This results in a flatter trajectory and better performance at longer range. In the years between World War I and World War II the 7x64mm was often regarded by German hunters as a “miracle cartridge” and dozens of different factory loads where available on the German market. It was that highly regarded the German Wehrmacht (Army) during the 1930s even considered replacing the 8x57mm IS in favour for the 7x64mm for their snipers. The Wehrmacht decided - just like the German army in 1912 - to stick to the 8x57mm IS cartridge for their Mauser Karabiner 98k to keep things as simple as possible in their logistical chain.

Beside the 7x64mm rifle cartridge Brenneke also designed a rimmed version for break action rifles of the cartridge in 1917. The rimmed 7x65mm R variant of the cartridge was also immediately a commercial success.

Cartridge dimensions

The 7x64mm has 4.48 ml (69 grains H2O) cartridge case capacity. A sign of the era in which the 7x64mm was developed are the gently sloped shoulders. The exterior shape of the case was designed to promote reliable case feeding and extraction in bolt-action rifles, under extreme conditions.

7x64mm maximum C.I.P. cartridge dimensions. All sizes in millimeters (mm).

Americans would define the shoulder angle at alpha/2 ≈ 20.42 degrees. The common rifling twist rate for this cartridge is 220 mm (1 in 8.66 in), 4 grooves, Ø lands = 6.98 mm, Ø grooves = 7.24 mm, land width = 3.70 mm and the primer type is large rifle or large rifle magnum depending on the load.

According to the official with C.I.P. (Commission Internationale Permanente Pour L'Epreuve Des Armes A Feu Portative) guidelines the 7x64mm case can handle up to 415 MPa (60190 psi) piezo pressure. In C.I.P. regulated countries every rifle cartridge combo has to be proofed at 125% of this maximum C.I.P. pressure to certify for sale to consumers.

The American .280 Remington cartridge is probably the closest ballistic twin of the 7x64mm. When compared to the 7x64mm the .280 Remington has a slightly lower maximum allowed chamber pressure and as an American 7 mm cartridge has a slightly smaller bore. European 7 mm cartridges all have 7.24 mm (0.285 in) grooves Ø diameter. American 7 mm cartridges have 7.21 mm (0.284 in) grooves Ø.

Contemporary use

The 7x64mm is one of the favorite rifle cartridges in central Europe and is offered as a chambering option in every major European hunting rifle manufacturers products palette. The versatility of the 7x64mm for hunting all kinds of European game and the availability of numerous factory loads[2] all attribute to the 7x64mm chambering popularity. Loaded with short light bullets it can be used on small European game like roe deer and chamois. Loaded with long heavy bullets it can be used on big European game like boar, red deer, moose and brown bear. The 7x64mm offers very good penetrating ability due to a fast twist rate that enables it to fire long, heavy bullets with a high sectional density. The 7x64mm rimmed sister cartridge, the 7x65mm R, is also very popular in central Europe for the same reasons as the 7x64mm. The (former) legal banning of (ex) military service cartridges like the .308 Winchester, 7x57mm, 8x57mm I, 8x57mm IS and the .30-06 Springfield in countries like France and Belgium also promoted acceptance and use of the 7x64mm and the 7x65mm R.

See also

References

  1. ^ Barnes, Frank C. (1997) [1965]. McPherson, M.L. (ed.). Cartridges of the World (8th Edition ed.). DBI Books. pp. 355, 374. ISBN 0-87349-178-5. {{cite book}}: |edition= has extra text (help)
  2. ^ The RWS Ammunition Ballistic Data & Application Consultant shows several 7x64mm factory loads

External links

Retrieved from "https://en.wikipedia.org/w/index.php?title=7×64mm&oldid=306300956"