Go/no go gauge
|This article needs additional citations for verification. (July 2010)|
A Go-No gauge (or Go/no go) refers to an inspection tool used to check a workpiece against its allowed tolerances. Its name derives from its use: the gauge has two tests; the check involves the workpiece having to pass one test (Go) and fail the other (No Go).
A Go NoGo gauge is a measuring tool that does not return a size in the conventional sense, but instead returns a state. The state is either acceptable (the part is within tolerance and may be used) or it is unacceptable (and must be rejected).
They are well suited for use in the production area of the factory as they require little skill or interpretation to use effectively and have few, if any, moving parts to be damaged in the often hostile production environment.
These gauges are referred to as plug gauges; they are used in the manner of a plug. They are generally assembled from standard parts where the gauge portion is interchangeable with other gauge pieces (obtained from a set of pin type gauge blocks) and a body that uses the collet principle to hold the gauges firmly. To use this style of gauge, one end is inserted into the part first and depending on the result of that test, the other end is tried.
In the right hand image, the top gauge is a thread gauge that is screwed into the part to be tested, the labeled GO end will enter into the part fully, the NOT GO end should not. The lower image is a plain plug gauge used to check the size of a hole, the green end is the GO, red is the NO GO. The tolerance of the part this gauge checks is 0.30mm where the lower size of the hole is 12.60mm and the upper size is 12.90mm, every size outside this range is out of tolerance. This may be initially expressed on the parts drawing in a number of styles, three possibilities may be:
- 12.75mm +/- 0.15mm
- 12.60mm +0.30 -0.00
- 12.90mm +0.00 -0.30
Snap gauges (or snap gage) are often used when a large quantity of work pieces must be inspected. The snap gauge has four anvils or jaws, the first one or pair (outermost) are set using the upper limit (tolerance) of the part and the inner set adjusted to the lower limit of the part. A correctly machined part will pass the first set of jaws and stop at the second — end of test. In this manner a part may be checked in one action, unlike the plug gauge that needs to be used twice and flipped to access the second gauge. The first go-no-go snap gage for checking thread rolls was invented in 1943 to speed production of parts during World War Two.
Once the concept is understood, the principle of operation can lead to all manner of designs where internal grooves, keyways, splines etc. may be measured in a simple yet effective manner. These will often be made to order by the toolmakers, or a related skilled tradesman.
Go/No-Go gauges play an integral part in setting the correct headspace during gunsmithing. In order for the chamber to be in-spec, the bolt must close without resistance on the Go gauge, but it must not close completely on the No-Go gauge. In addition, there is usually a third gauge called FIELD that is slightly larger than the No-Go gauge. Since bolt and chamber lugs eventually stretch with use (although thousands and thousands of rounds need to be fired for that to happen), the bolt may start to close on the No-Go gauge. If the bolt also closes fully on the field gauge, such a gun is considered unsafe due to high risk of shell case rupture if the cartridges length happens to be on the shorter end of the spec.
A special match-grade Go gauge can also be employed to verify a particularly tight, or shorter-than-SAAMI spec chamber length. Such gauges are usually special-ordered from chamber reamer manufacturers. This minimizes case stretch or end-play in order to best control the positioning of an unfired round prior to its firing in a match-grade chamber. Such chambers are also usually cut to tighter dimensions in the case neck area. Thus a standard Go gauge may not actually chamber as easily due to these reduced dimensions, even if they are cut properly.
- Hoffman, Edward G. (1985). Fundamentals of Tool Design. Dearborn: Society of Manufacturing Engineers (SME) Publications/Marketing Division. pp. 499–502. ISBN 0-87263-134-6.
- "Snap Gage for Checking Threads Combines Go-no-Go Limits" Popular Mechanics, December 1943 left side of page
- Limit (GO & NO GO) Gauges
- Technicial Specification on Plug (GO / NO GO) Gauges