Jump to content

Thiocarbanilide

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Citation bot (talk | contribs) at 19:30, 27 October 2022 (Misc citation tidying. | Use this bot. Report bugs. | Suggested by AManWithNoPlan | #UCB_CommandLine). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Thiocarbanilide
Thiocarbanilide
Names
Preferred IUPAC name
N,N′-Diphenylthiourea
Other names
1,3-Diphenylthiourea
sym-Diphenylthiourea
Diphenylthiourea
1,3-Diphenyl-2-thiourea
DPTU
Sulfocarbanilide
Identifiers
3D model (JSmol)
ChEMBL
ChemSpider
ECHA InfoCard 100.002.732 Edit this at Wikidata
UNII
  • InChI=1S/C13H12N2S/c16-13(14-11-7-3-1-4-8-11)15-12-9-5-2-6-10-12/h1-10H,(H2,14,15,16) checkY
    Key: FCSHMCFRCYZTRQ-UHFFFAOYSA-N checkY
  • InChI=1/C13H12N2S/c16-13(14-11-7-3-1-4-8-11)15-12-9-5-2-6-10-12/h1-10H,(H2,14,15,16)
    Key: FCSHMCFRCYZTRQ-UHFFFAOYAC
  • S=C(Nc1ccccc1)Nc2ccccc2
Properties
C13H12N2S
Molar mass 228.312 g/mol
Appearance White powder
Density 1.32 g/cm3
Melting point 154.5 °C (310.1 °F; 427.6 K)
Boiling point decomposes
slightly soluble in water
Solubility very soluble in ethanol, diethyl ether, chloroform[1]
Hazards
NFPA 704 (fire diamond)
NFPA 704 four-colored diamondHealth 2: Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury. E.g. chloroformFlammability 1: Must be pre-heated before ignition can occur. Flash point over 93 °C (200 °F). E.g. canola oilInstability 0: Normally stable, even under fire exposure conditions, and is not reactive with water. E.g. liquid nitrogenSpecial hazards (white): no code
2
1
0
Flash point 164.7 °C (328.5 °F; 437.8 K)
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
checkY verify (what is checkY☒N ?)

Thiocarbanilide is an organic chemical compound with the formula (C6H5NH)2CS. This white solid is a derivative of thiourea. It is prepared by the reaction of aniline and carbon disulfide.

Uses

Thiocarbanilide is commonly used as a vulcanization accelerator for rubber,[2] and as a stabilizer for PVC and PVDC. Its use as a vulcanization accelerator was discovered by BF Goodrich chemist George Oenslager.[3]

Reactions

Thiocarbanilide reacts with phosphorus pentachloride or hydrochloric acid, dilute sulfuric acid, acetic anhydride or iodine to produce phenyl isothiocyanate.[citation needed]

Toxicology

Oral, rat: LD50 = 50 mg/kg.

References

  1. ^ Lide, David R. (1998), Handbook of Chemistry and Physics (87 ed.), Boca Raton, Florida: CRC Press, pp. 3–242, ISBN 0-8493-0594-2
  2. ^ Hans-Wilhelm Engels, Herrmann-Josef Weidenhaupt, Manfred Pieroth, Werner Hofmann, Karl-Hans Menting, Thomas Mergenhagen, Ralf Schmoll, Stefan Uhrlandt "Rubber, 4. Chemicals and Additives" in Ullmann's Encyclopedia of Industrial Chemistry 2004, Wiley-VCH, Weinheim. doi:10.1002/14356007.a23_365.pub2
  3. ^ Trumbull, H. L. (1933). "Accomplishments of the Medalist". Ind. Eng. Chem. 25 (2): 230–232. doi:10.1021/ie50278a030.


Stub icon

This article about an organic compound is a stub. You can help Wikipedia by expanding it.

Retrieved from "https://en.wikipedia.org/w/index.php?title=Thiocarbanilide&oldid=1118574740"