Amplitude

For quantum-mechanical amplitude, see probability amplitude. For the video game of the same name, see Amplitude (video game). Peak to Peak redirects here. For the school of that name, see Peak to Peak Charter School

Amplitude is the magnitude of change in the oscillating variable, with each oscillation, within an oscillating system. For instance, sound waves are oscillations in atmospheric pressure and their amplitudes are proportional to the change in pressure during one oscillation. If the variable undergoes regular oscillations, and a graph of the system is drawn with the oscillating variable as the vertical axis and time as the horizontal axis, the amplitude is visually represented by the vertical distance between the extrema of the curve. In older texts the phase is sometimes very confusingly called the amplitude.

Concepts of amplitude

===Peak-to-peak amplitude=== TOM ANDERSON IS A WILLY AND LOVES TOM POSTELLELELES Peak-to-peak amplitude is the measure of the change between peak (highest amplitude value) and trough (lowest amplitude value, which can be negative). Peak-to-peak amplitudes can be measured by meters with appropriate circuitry, or by viewing the waveform on an oscilloscope. Peak-to-peak is a straightforward measurement to make on an oscilloscope, the peaks of the waveform being easily identified and measured against the graticule. It remains a common way of specifying amplitude but sometimes other measures of amplitude are more appropriate.

Peak amplitude

In audio system measurements, telecommunications and other areas where the measurand is a signal that swings above and below a zero value but is not sinusoidal, peak amplitude is often used. This is the absolute value of the signal.

Semi-amplitude

Semi-amplitude in fields such as astronomy is understood to mean half the peak-to-peak amplitude. For a sine wave, peak amplitude and semi-amplitude are the same.

Some scientists use "amplitude" or "peak amplitude" to mean semi-amplitude, that is, half the peak-to-peak amplitude.

Root mean square amplitude

Root mean square (RMS) amplitude is used especially in electrical engineering: the RMS is defined as the square root of the mean over time of the square of the vertical distance of the graph from the rest state.

For complex waveforms, especially non-repeating signals like noise, the RMS amplitude is usually used because it is unambiguous and because it has physical significance. For example, the average power transmitted by an acoustic or electromagnetic wave or by an electrical signal is proportional to the square of the RMS amplitude (and not, in general, to the square of the peak amplitude).

A sinusoidal curve
1 = Peak amplitude ($\scriptstyle {\hat {U}}$),
2 = Peak-to-peak amplitude ($\scriptstyle 2{\hat {U}}$),
3 = RMS amplitude ($\scriptstyle {\hat {U}}/{\sqrt {2}}$),
4 = Wave period (not an amplitude)

When dealing with alternating current electrical power it is universal to specify RMS values of a sinusoidal waveform. The peak-to-peak voltage of a sine wave is nearly 3 times the RMS value, but is a rarely used measure in this field. Some common meter types used in electrical engineering are calibrated for RMS amplitude, but actually operate on a DC input. Digital voltmeters and moving coil meters are both in this category. Such meters require the AC input to be first rectified and are really reading proportional to either rectified average or peak amplitiude. They are not true RMS meters and the RMS calibration is only correct for a sine wave input since the ratio between peak, average and rms values is dependant on waveform. True RMS meters do exist but until recently have been considered more specialised equipment; the advent of microprocessor controlled meters has made them more common.

Ambiguity of amplitude

The use of peak amplitude is simple and unambiguous for symmetric, periodic waves, like a sine wave, a square wave, or a triangular wave. For an asymmetric wave (periodic pulses in one direction, for example), the peak amplitude becomes ambiguous because the value obtained is different depending on whether the maximum positive signal is measured relative to the mean, the maximum negative signal is measured relative to the mean, or the maximum positive signal is measured relative to the maximum negative signal (the peak-to-peak amplitude) and then divided by two. In electrical engineering, the usual solution to this ambiguity is to measure the amplitude from a defined reference potential (such as ground or 0V). Strictly speaking, this is no longer amplitude since there is the possibility that a constant (DC component) is included in the measurement.

Pulse amplitude

In telecommunication, pulse amplitude is the magnitude of a pulse parameter, such as the voltage level, current level, field intensity, or power level.

Pulse amplitude is measured with respect to a specified reference and therefore should be modified by qualifiers, such as "average", "instantaneous", "peak", or "root-mean-square."

Pulse amplitude also applies to the amplitude of frequency- and phase-modulated waveform envelopes.

Formal representation

In this simple wave equation

$x=A\sin(t-K)+b\ ,$

A is the amplitude of the wave,
x is the oscillating variable,
t is time,
K and b are arbitrary constants representing time and displacement offsets respectively.

The units of the amplitude depend on the type of wave, but are always in the same units as the oscillating variable. A more general representation of the wave equation is more complex, but the role of amplitude remains analogous to this simple case.

For waves on a string, or in medium such as water, the amplitude is a displacement.

The amplitude of sound waves and audio signals (which relates to the volume) conventionally refers to the amplitude of the air pressure in the wave, but sometimes the amplitude of the displacement (movements of the air or the diaphragm of a speaker) is described. The logarithm of the amplitude squared is usually quoted in dB, so a null amplitude corresponds to -∞ dB. Loudness is related to amplitude and intensity and is one of most salient qualities of a sound, although in general sounds can be recognized independently of amplitude. The square of the amplitude is proportional to the intensity of the wave.

For electromagnetic radiation, the amplitude of a photon corresponds to the changes in the electric field of the wave. However radio signals may be carried by electromagnetic radiation; the intensity of the radiation (amplitude modulation) or the frequency of the radiation (frequency modulation) is oscillated and then the individual oscillations are varied (modulated) to produce the signal.

Waveform and envelope

The amplitude may be constant (in which case the wave is a continuous wave) or may vary with time and/or position. The form of the variation of amplitude is called the envelope of the wave.

If the waveform is a pure sine wave, the relationships between peak-to-peak, peak, mean, and RMS amplitudes are fixed and known, as they are for any continuous periodic wave. However, this is not true for an arbitrary waveform which may or may not be periodic or continuous.

For a sine wave the relationship between RMS and peak-to-peak amplitude is:

${\mbox{Peak-to-peak}}=2{\sqrt {2}}\times {\mbox{RMS}}\approx 2.8\times {\mbox{RMS}}\,$.

For other waveforms the relationships are not (necessarily) arithmetically the same as they are for sine waves.

See also

• Waves and their properties:
  • Frequency
  • Period
  • Wavelength
  • Crest factor
• Amplitude modulation

Further reading

• Goldvais, A. Goldvais. Exoplanets. Retrieved 2008-08-22