Breakdown voltage: Difference between revisions

Content deleted Content added

Inline

Revision as of 09:26, 22 July 2010

The breakdown voltage of an Insulator is the minimum voltage that causes a portion of an insulator to become electrically conductive.

The breakdown voltage of a diode is the minimum reverse voltage to make the diode conduct in reverse. Some devices (such as TRIACs) also have a forward breakdown voltage.^[1]

In Detail

Insulators

Breakdown voltage is a characteristic of an insulator that defines the maximum voltage difference that can be applied across the material before the insulator collapses and conducts. In solid insulating materials, this usually creates a weakened path within the material by creating permanent molecular or physical changes by the sudden current. Within rarefied gases found in certain types of lamps, breakdown voltage is also sometimes called the "striking voltage".^[2]

The breakdown voltage of a material is not a definite value because it is a form of failure and there is a statistical probability whether the material will fail at a given voltage. When a value is given it is usually the mean breakdown voltage of a large sample. Another term is also 'withstand voltage' where the probability of failure at a given voltage is so low it is considered, when designing insulation, that the material will not fail at this voltage.^[3]

Two different breakdown voltage measurements of a material are the AC and impulse breakdown voltages. The AC voltage is the line frequency of the mains (either 50 or 60 Hz depending on where you live). The impulse breakdown voltage is simulating lightning strikes, and usually uses a 1.2 microsecond rise for the wave to reach 90% amplitude then drops back down to 50% amplitude after 50 microseconds.^[4]

Two technical standards governing performing these tests are ASTM D1816 and ASTM D3300 published by ASTM.^[5]

Breakdown in vacuum

In standard conditions at atmospheric pressure, gas serves as an excellent insulator, requiring the application of a significant voltage before breaking down (e.g. lightning). In partial vacuum, this breakdown potential may decrease to an extent that two uninsulated surfaces with different potentials might induce the electrical breakdown of the surrounding gas. This has some useful applications in industry (e.g. the production of microprocessors) but in other situations may damage an apparatus, as breakdown is analogous to a short circuit.^[6]

The breakdown voltage in a partial vacuum is represented as^[7]^[8] ^[9]:

$V_{\mathrm {b} }={\frac {Bpd}{\ln Apd-\ln(1+{\frac {1}{\gamma _{\mathrm {se} }}})}}$

where $V_{\mathrm {b} }$ is the breakdown potential in volts DC, $A$ and $B$ are constants that depend on the surrounding gas, $p$ represents the pressure of the surrounding gas, $d$ represents the distance in centimetres between the electrodes, and $\gamma _{\mathrm {se} }$ represents the Secondary Electron Emission Coefficient.^[10]

Diodes

Breakdown voltage is a parameter of a diode that defines the largest reverse voltage that can be applied without causing an exponential increase in the current in the diode. As long as the current is limited, exceeding the breakdown voltage of a diode does no harm to the diode. In fact, Zener diodes are essentially just heavily doped normal diodes that exploit the breakdown voltage of a diode to provide regulation of voltage levels.

References

^ Emelyanov, A.A. and Emelyanova, E.A., Abstracts of Papers, Proc. XXII ISDEIV, Matsue, 2006, vol. 1, p. 37.
^ J. M. Meek and J. D. Craggs, Electrical Breakdown of Gases, John Wiley & Sons, Chichester, 1978.
^ Relationship between Electrode Surface Roughness and Impulse Breakdown Voltage in Vacuum Gap of Cu and Cu-Cr Electrodes, Shinji Sato and Kenichi Koyama, Mitsubishi Electric Corporation, Advanced Technology R & D Center, 8-1-1 Tsukaguchi-Honmachi, Amagasaki-City, Hyogo 661-8661, Japan
^ Emelyanov, A.A., Izv. Vyssh. Uchebn. Zaved., Fiz., 1989, no. 4, p. 103.
^ Kalyatskii, I.I., Kassirov, G.M., and Smirnov, G.V., Prib. Tekh. Eksp., 1974, no. 4, p. 84.
^ Stefanov, L.S., Tekhnika vysokikh napryazhenii (High-Voltage Engineering), Leningrad: Energiya, 1967.
^ G. Cuttone, C. Marchetta, L. Torrisi, G. Della Mea, A. Quaranta, V. Rigato and S. Zandolin, Surface Treatment of HV Electrodes for Superconducting Cyclotron Beam Extraction, IEEE. Trans. DEI, Vol. 4, pp. 218<223, 1997.
^ H. Moscicka-Grzesiak, H. Gruszka and M. Stroinski, ‘‘Influence of Electrode Curvature on Predischarge Phenomena and Electric Strength at 50 Hz of a Vacuum
^ R. V. Latham, High Voltage Vacuum Insulation: Basic concepts and technological practice, Academic Press, London, 1995.
^ Yemelyanov, A.A., Kalyatskiy, I.I., Kassirov, G.M., and Smirnov, G.V., Abstracts of Papers, Proc. VII ISDEIV, Novosibirsk, 1976, p. 130.

forward and reverse voltage between the gap

@@ Line 43: / Line 43: @@
 ==References==
 {{reflist}}
+forward and reverse voltage between the gap
 ==See also==