TRIAC: Difference between revisions
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
[[Image:triac.jpg|right|thumb| |
[[Image:triac.jpg|right|thumb|Triac Schematic Symbol]] |
||
A '''TRIAC''', or '''TRIode for Alternating Current''' is an [[Electronics|electronic]] component approximately equivalent to two [[silicon controlled rectifier]]s (SCRs/[[thyristor]]s) joined in [[Antiparallel|inverse parallel]] (paralleled but with the polarity reversed) and with their gates connected together. This results in a bidirectional electronic switch which can conduct [[electric current|current]] in either direction when it is triggered (turned on). It can be triggered by either a positive or a negative [[voltage]] being applied to its ''gate'' electrode. Once triggered, the device continues to conduct until the current through it drops below a certain threshold value, such as at the end of a half-cycle of [[alternating current]] (AC) mains power. This makes the TRIAC a very convenient switch for AC circuits, allowing the control of very large power flows with [[milliampere]]-scale control currents. In addition, applying a trigger pulse at a controllable point in an AC cycle allows one to control the percentage of current that flows through the TRIAC to the load (so-called ''phase control''). |
A '''TRIAC''', or '''TRIode for Alternating Current''' is an [[Electronics|electronic]] component approximately equivalent to two [[silicon controlled rectifier]]s (SCRs/[[thyristor]]s) joined in [[Antiparallel|inverse parallel]] (paralleled but with the polarity reversed) and with their gates connected together. This results in a bidirectional electronic switch which can conduct [[electric current|current]] in either direction when it is triggered (turned on). It can be triggered by either a positive or a negative [[voltage]] being applied to its ''gate'' electrode. Once triggered, the device continues to conduct until the current through it drops below a certain threshold value, such as at the end of a half-cycle of [[alternating current]] (AC) mains power. This makes the TRIAC a very convenient switch for AC circuits, allowing the control of very large power flows with [[milliampere]]-scale control currents. In addition, applying a trigger pulse at a controllable point in an AC cycle allows one to control the percentage of current that flows through the TRIAC to the load (so-called ''phase control''). |
||
[[Image:Triace.jpg|right|Thumb|Triac Equivilant circuit]] |
|||
Low power TRIACs are used in many applications such as [[electric light|light]] [[dimmer]]s, speed controls for [[electric fan]]s and other [[electric motor]]s, and in the modern computerized control circuits of many household [[Small appliance|small]] and [[major appliance]]s. However, when used with [[inductor|inductive]] loads such as electric fans, care must be taken to assure that the TRIAC will turn off correctly at the end of each half-cycle of the ac power. A [[snubber]] circuit is often used to assist this turn off. Snubber circuits are also used to prevent premature triggering. For higher-powered, more-demanding loads, two [[thyristor|SCRs]] in inverse parallel may be used instead of one TRIAC. Because each SCR will have an entire half-cycle of reverse polarity voltage applied to it, turn-off of the SCRs is assured, no matter what the character of the load. |
Low power TRIACs are used in many applications such as [[electric light|light]] [[dimmer]]s, speed controls for [[electric fan]]s and other [[electric motor]]s, and in the modern computerized control circuits of many household [[Small appliance|small]] and [[major appliance]]s. However, when used with [[inductor|inductive]] loads such as electric fans, care must be taken to assure that the TRIAC will turn off correctly at the end of each half-cycle of the ac power. A [[snubber]] circuit is often used to assist this turn off. Snubber circuits are also used to prevent premature triggering. For higher-powered, more-demanding loads, two [[thyristor|SCRs]] in inverse parallel may be used instead of one TRIAC. Because each SCR will have an entire half-cycle of reverse polarity voltage applied to it, turn-off of the SCRs is assured, no matter what the character of the load. |
||
Revision as of 22:23, 17 July 2006
A TRIAC, or TRIode for Alternating Current is an electronic component approximately equivalent to two silicon controlled rectifiers (SCRs/thyristors) joined in inverse parallel (paralleled but with the polarity reversed) and with their gates connected together. This results in a bidirectional electronic switch which can conduct current in either direction when it is triggered (turned on). It can be triggered by either a positive or a negative voltage being applied to its gate electrode. Once triggered, the device continues to conduct until the current through it drops below a certain threshold value, such as at the end of a half-cycle of alternating current (AC) mains power. This makes the TRIAC a very convenient switch for AC circuits, allowing the control of very large power flows with milliampere-scale control currents. In addition, applying a trigger pulse at a controllable point in an AC cycle allows one to control the percentage of current that flows through the TRIAC to the load (so-called phase control).
Low power TRIACs are used in many applications such as light dimmers, speed controls for electric fans and other electric motors, and in the modern computerized control circuits of many household small and major appliances. However, when used with inductive loads such as electric fans, care must be taken to assure that the TRIAC will turn off correctly at the end of each half-cycle of the ac power. A snubber circuit is often used to assist this turn off. Snubber circuits are also used to prevent premature triggering. For higher-powered, more-demanding loads, two SCRs in inverse parallel may be used instead of one TRIAC. Because each SCR will have an entire half-cycle of reverse polarity voltage applied to it, turn-off of the SCRs is assured, no matter what the character of the load.