MAC address
In computer networking a Media Access Control address (MAC address) or Ethernet Hardware Address (EHA) or hardware address or adapter address is a quasi-unique identifier attached to most network adapters (NIC or Network Interface Card). It is a number that serves as an identifier for a particular network adapter. Thus network cards (or built-in network adapters) in two different computers will have different MAC addresses, as would an Ethernet adapter and a wireless adapter in the same computer, and as would multiple network cards in a router. However, it is possible to change the MAC address on most of today's hardware, often referred to as MAC spoofing.
Most layer 2 network protocols use one of three numbering spaces managed by the IEEE: MAC-48, EUI-48, and EUI-64, which are designed to be globally unique. Not all communications protocols use MAC addresses, and not all protocols require globally unique identifiers. The IEEE claims trademarks on the names "EUI-48" and "EUI-64" ("EUI" stands for Extended Unique Identifier).
MAC addresses, unlike IP addresses and IPX addresses, are not divided into "host" and "network" portions. Therefore, a host cannot determine from the MAC address of another host whether that host is on the same layer 2 network segment as the sending host or a network segment bridged to that network segment.
ARP is commonly used to convert from addresses in a layer 3 protocol such as Internet Protocol (IP) to the layer 2 MAC address. On broadcast networks, such as Ethernet, the MAC address allows each host to be uniquely identified and allows frames to be marked for specific hosts. It thus forms the basis of most of the layer 2 networking upon which higher OSI Layer protocols are built to produce complex, functioning networks.
Notational conventions
The standard (IEEE 802) format for printing MAC-48 addresses in human-readable media is six groups of two hexadecimal digits, separated by hyphens (-) in transmission order, e.g. 01-23-45-67-89-ab. This form is also commonly used for EUI-64. Other conventions include six groups of two separated by colons (:), e.g. 01:23:45:67:89:ab; or three groups of four hexadecimal digits separated by dots (.), e.g. 0123.4567.89ab; again in transmission order.
Address details
The original IEEE 802 MAC address comes from the original Xerox Ethernet addressing scheme.[1] This 48-bit address space contains potentially 248 or 281,474,976,710,656 possible MAC addresses.
All three numbering systems use the same format and differ only in the length of the identifier. Addresses can either be "universally administered addresses" or "locally administered addresses."
A universally administered address is uniquely assigned to a device by its manufacturer; these are sometimes called "burned-in addresses" (BIA). The first three octets (in transmission order) identify the organization that issued the identifier and are known as the Organizationally Unique Identifier (OUI). The following three (MAC-48 and EUI-48) or five (EUI-64) octets are assigned by that organization in nearly any manner they please, subject to the constraint of uniqueness. The IEEE expects the MAC-48 space to be exhausted no sooner than the year 2100; EUI-64s are not expected to run out in the foreseeable future.
A locally administered address is assigned to a device by a network administrator, overriding the burned-in address. Locally administered addresses do not contain OUIs.
Universally administered and locally administered addresses are distinguished by setting the second most significant bit of the most significant byte of the address. If the bit is 0, the address is universally administered. If it is 1, the address is locally administered. The bit is 0 in all OUIs. For example, 02-00-00-00-00-01. The most significant byte is 02h. The binary is 00000010 and because Ethernet transmit octets with the least significant bit first, bit order has to be read backwards and the second most significant bit is 1. Therefore, it is a locally administered address.[2]
If the most significant bit of the most significant byte is set to a 0, the packet is meant to reach only one receiving NIC. This is called unicast. If the most significant bit of the most significant byte is set to a 1, the packet is meant to be sent only once but still reach several NICs. This is called multicast.
MAC-48 and EUI-48 addresses are usually shown in hexadecimal format, with each octet separated by a dash or colon. An example of a MAC-48 address would be "00-08-74-4C-7F-1D". If you cross-reference the first three octets with IEEE's OUI assignments,[3] you can see that this MAC address came from Dell Computer Corp. The last three octets represent the serial number assigned to the adapter by the manufacturer.
The following technologies use the MAC-48 identifier format:
- Ethernet
- 802.11 wireless networks
- Bluetooth
- IEEE 802.5 token ring
- most other IEEE 802 networks
- FDDI
- ATM (switched virtual connections only, as part of an NSAP address)
- Fibre Channel and Serial Attached SCSI (as part of a World Wide Name)
The distinction between EUI-48 and MAC-48 identifiers is purely semantic: MAC-48 is used for network hardware; EUI-48 is used to identify other devices and software. (Thus, by definition, an EUI-48 is not in fact a "MAC address", although it is syntactically indistinguishable from one and assigned from the same numbering space.)
Note: The IEEE now considers the label MAC-48 to be an obsolete term which was previously used to refer to a specific type of EUI-48 identifier used to address hardware interfaces within existing 802-based networking applications and should not be used in the future. Instead, the term EUI-48 should be used for this purpose.
EUI-64 identifiers are used in:
- FireWire
- IPv6 (as the low-order 64 bits of a unicast network address when temporary addresses are not being used)
- ZigBee / 802.15.4 wireless personal-area networks
The IEEE has built in several special address types to allow more than one Network Interface Card to be addressed at one time:
- Packets sent to the broadcast address, all one bits, are received by all stations on a local area network. In hexadecimal the broadcast address would be "FF:FF:FF:FF:FF:FF".
- Packets sent to a multicast address are received by all stations on a LAN that have been configured to receive packets sent to that address.
- Functional addresses identify one of more Token Ring NICs that provide a particular service, defined in IEEE 802.5.
These are "group addresses", as opposed to "individual addresses"; the most significant bit of the first octet of a MAC address distinguishes individual addresses from group addresses. That bit is set to 0 in individual addresses and 1 in group addresses. Group addresses, like individual addresses, can be universally administered or locally administered.
In addition, the EUI-64 numbering system encompasses both MAC-48 and EUI-48 identifiers by a simple translation mechanism. To convert a MAC-48 into an EUI-64, copy the OUI, append the two octets "FF-FF", and then copy the organization-specified part. To convert an EUI-48 into an EUI-64, the same process is used, but the sequence inserted is "FF-FE". In both cases, the process can be trivially reversed when necessary. Organizations issuing EUI-64s are cautioned against issuing identifiers that could be confused with these forms. The IEEE policy is to discourage new uses of 48-bit identifiers in favor of the EUI-64 system.
IPv6—one of the most prominent standards that uses EUI-64—applies these rules inconsistently. Due to an error in the appendix to the specification of IPv6 addressing, it is standard practice to extend MAC-48 addresses (such as IEEE 802 MAC address) to EUI-64 using "FF-FE" rather than "FF-FF."
Individual address block
An Individual Address Block comprises a 24-bit OUI managed by the IEEE Registration Authority, followed by 12 IEEE-provided bits (identifying the organization), and 12 bits for the owner to assign to individual devices. An IAB is ideal for organizations requiring fewer than 4097 unique 48-bit numbers (EUI-48).[4]
Bit-reversed notation
The standard transmission order notation for MAC addresses, as seen in the output of the ifconfig command for example, is also called canonical format.
However, since IEEE 802.3 (Ethernet) and IEEE 802.4 (Token Bus) send the bits over the wire with least significant bit first, while IEEE 802.5 (Token Ring) and IEEE 802.6 send the bits over the wire with most significant bit first, confusion may arise where an address in the latter scenario is represented with bits reversed from the canonical representation. So for instance, an address whose canonical form is 12-34-56-78-9A-BC would be transmitted over the wire as bits 01001000 00101100 01101010 00011110 01011001 00111101 in the standard transmission order (least significant bit first). But for Token Ring networks, it would be transmitted as bits 00010010 00110100 01010110 01111000 10011010 10111100 in most significant bit first order. If care is not taken to translate correctly and consistently to the canonical representation, the latter might be displayed as 482C6A1E593D, which could cause confusion. This would be referred to as "Bit-reversed order", "Non-canonical form", "MSB format", "IBM format", or "Token Ring format" as explained by RFC 2469. Canonical form is preferred.
See also
- NSAP address, another endpoint addressing scheme.
- Cisco Hot Standby Router Protocol or standard alternative VRRP Virtual router redundancy protocol, which allows multiple routers to share one IP address and MAC address to provide router redundancy. The OpenBSD project has an open source alternative, the Common Address Redundancy Protocol (CARP).