Driving cycle
![]() | This article includes a list of general references, but it lacks sufficient corresponding inline citations. (November 2009) |
This article is part of a series on |
Driving cycles |
---|
Europe |
NEDC: ECE R15 (1970) / EUDC (1990) (UN ECE regulations 83 and 101) |
United States |
EPA Federal Test: FTP 72/75 (1978) / SFTP US06/SC03 (2008) |
Japan |
10 mode (1973) / 10-15 Mode (1991) / JC08 (2008) |
Global Technical Regulations |
WLTP (2015) (Addenda 15) |
A driving cycle is a series of data points representing the speed of a vehicle versus time.
Driving cycles are produced by different countries and organizations to assess the performance of vehicles in various ways, as for example fuel consumption and polluting emissions.[1][2][3]
Fuel consumption and emission tests are performed on chassis dynamometers. Tailpipe emissions are collected and measured to indicate the performance of the vehicle.
Another use for driving cycles is in vehicle simulations. More specifically, they are used in propulsion system simulations to predict performance of internal combustion engines, transmissions, electric drive systems, batteries, fuel cell systems, and similar components.
Some driving cycles are derived theoretically, as it is preferred in the European Union, whereas others are direct measurements of a driving pattern deemed representative.
There are two types of driving cycles:
- Transient driving cycles involve many changes, representing the constant speed changes typical of on-road driving.
- Modal driving cycles involve protracted periods at constant speeds.
The American FTP-75,[4] and the unofficial European Hyzem driving cycles are transient, whereas the Japanese 10-15 Mode and JC08 cycles are modal cycles.
Some highly stylised transient driving cycles such as official European NEDC are designed to fit a particular requirement and bear little relation to real world driving patterns.[5] The most common driving cycles are probably the NEDC and the FTP-75, which correspond to urban driving conditions.
Driving cycle design is the core technology for these standard cycles.[clarification needed] Optimization and Markov chains are employed to design a driving cycle.[citation needed]
Drive cycle recognition is applying to Hybrid Electric Vehicle.[clarification needed]
Data Collection
Data collection from the test road is the most important activity. Test road (e.g. city, highway, etc.) measured data are the inputs to the 'Drive Cycle' preparation activity.
The procedure involves instrumentation of the test vehicle to collect information while driving on the test road. There are two major types of data to be collected, Driver behavior and vehicle vs Road data. The vehicle vs road data are used to prepare the road drive cycle and the driver data to prepare the Driver model. for example, to calculate a vehicle's fuel consumption either in computer simulation or in chassis dynamo-meter which is going to be launched in India, it must run on an Indian road with an Indian Driver. Indian Drive Cycle with a European driver model does not give a fair comparison of the on road trials.
Driving Cycle Design
The "Drive-cycle" basically is the representative of the road. Drive cycles are used to reduce the expense of on road tests, time of test and fatigue of the test engineer. The whole idea is to bring the road to the test lab (a chassis dynamo-meter) or to the computer simulation.
Two kinds of drive cycle can be made. One is DISTANCE DEPENDENT (SPEED vs DISTANCE vs ALTITUDE) and the other one is TIME DEPENDENT (SPEED VS TIME VS GEAR SHIFT). The DISTANCE DEPENDENT is the actual replica of the test road whereas TIME DEPENDENT is the compressed version of the actual time taken to conduct the test on road. Examples of TIME DEPENDENT drive cycles are European NEDC cycle, FTP-75. TIME DEPENDENT drive cycles are used specifically for chassis dynamo meter testing because in a short time the results can be availed and repeated tests can be done easily.
Driving Cycle Recognition
Based on the type of application drive cycles are made. Drive cycle for passenger cars are different form commercial vehicle.
Driving Cycle Prediction
![]() | This section is empty. You can help by adding to it. (June 2011) |
References
- ^ Brundell-Freij, Karin; Ericsson, Eva (May 2005). "Influence of street characteristics, driver category and car performance on urban driving patterns". Transportation Research Part D: Transport and Environment. 10 (3). Elsevier: 213–229. doi:10.1016/j.trd.2005.01.001.
- ^ Ericsson, Eva (September 2000). "Variability in urban driving patterns". Transportation Research Part D: Transport and Environment. 5 (5). Elsevier: 337–354. doi:10.1016/S1361-9209(00)00003-1.
- ^ Ericsson, Eva (September 2001). "Independent driving pattern factors and their influence on fuel-use and exhaust emission factors". Transportation Research Part D: Transport and Environment. 6 (5). Elsevier: 325–345. doi:10.1016/S1361-9209(01)00003-7.
- ^ "Dynamometer Drive Schedules". US EPA. Retrieved 26 April 2014.
- ^ "A reference book of driving cycles for use in the measurement of road vehicle emissions" (PDF). Retrieved 11 August 2014.
External links
- US EPA Dynamometer Drive Schedules - Examples of driving cycles and downloadable data sets, including UDDS, FTP75, HWFET, US06, and others.
- Wheels: road load energy demand calculator - Online tool to calculate vehicle road load over a driving cycle
- DieselNet - Introduction to various standard driving cycles