Two-stroke engine
The two-stroke cycle of an internal combustion engine differs from the more common four-stroke cycle by having only two strokes (linear movements of the piston) instead of four, although the same four operations (intake, compression, power, exhaust) still occur. Thus, there is a power stroke per piston for every engine revolution, instead of every second revolution.
Two-stroke engines are used most among the smallest and largest reciprocating powerplants, but less commonly among medium sized ones.
The smallest gasoline engines are usually two-strokes. They are commonly used in outboard motors, high-performance, small-capacity motorcycles, mopeds, scooters, karting, and motorized garden appliances like chainsaws and lawnmowers. In each application, they are popular because of their simple design (and consequent low cost) and very high power-to-weight ratios (because the engine has twice as many combustions per second as a four stroke engine revolving at the same speed). For handheld devices, they also have the advantage of working in any orientation, as there is no oil reservoir.
Two-stroke cycles have also been used in diesel engines, notably opposed piston designs, low speed units such as large marine engines, and V8 engines for trucks and heavy machinery.
imposible technology, cant work, wont work
Two-stroke diesel engines
A two-stroke cycle has also been used for some diesel engines. As the fuel is injected directly into the cylinder, the lubrication of the crankshaft must be independent in these engines. There is no mixing of lubricating oil into the fuel.
There are three patterns. Some modern designs differ from the gasoline two-stroke cycle in that they have intake and exhaust valves in the cylinder head, exactly like a four-stroke engine. In these engines, the two-stroke cycle is used to improve power-to-weight ratio and/or reduce the engine speed to increase reliability. This pattern is common in truck, railroad locomotive and machinery engines.
Other engines have used the same ported arrangement as the gasoline two-stroke, although the charge air is generally delivered under pressure from a blower through ducting rather than through the crankcase. Examples are the Junkers Jumo 205 and Napier Deltic high-speed opposed piston engines.
A third pattern uses the induction method of the gasoline two-stroke, but with an exhaust valve in the cylinder head. Large marine diesels commonly use this arrangement. These engines commonly also use a crosshead bearing, which together with a sliding seal on the piston rod allows the air path to be separated from the crankshaft while still using the piston movement as an air pump.
The simpler stroke in the fully valved diesel two-stroke cycle is the compression stroke; both valves are closed, and the rising piston compresses the air, heating it. At the top of the stroke, diesel fuel is injected into the cylinder, where it ignites and burns. The hot, high pressure gases produced by the combustion push against the piston as it descends in the initial part of the second stroke, delivering power. At this point, both valves are still closed. When the piston nears the bottom of the stroke, the exhaust valve opens, and the exhaust gases, still under pressure, rush out. The intake valve then opens. Air under pressure rushes into the cylinder, blowing out the remainder of the exhaust gases. The exhaust valve closes at that point, and shortly after that, and at about bottom dead center, so does the intake valve.
If the crankcase is not used as an air pump, some other means of forced induction is required, and is often used for efficiency in any case. The intake air must be under pressure, since the engine does not have an induction stroke and cannot suck the air in by itself. A low-pressure supercharger (blower) is needed at minimum, but many are turbocharged.
The diesel two-stroke generally lacks the inefficiency and pollution problems of the gasoline two-stroke, since no unburned fuel, only air, can get blown out of the exhaust valve before it closes. Also, there is no mixing of lubricant with the fuel.
Compared with four-stroke engines
Two-stroke engines have several marked disadvantages that have largely precluded their use in automobiles (although there was some use, such as in historic Saabs and DKWs and until recently in Trabants) and are reducing their prevalence in the above applications. Firstly, they require much more fuel than a comparably powerful four-stroke engine due to less efficient combustion. The burning oil, and the less efficient combustion, makes their exhaust far smellier and more damaging than a four-stroke engine, thus struggling to meet current emission control laws. They are noisier, partly due to the more penetrating high-frequency buzzing and partly due to the fact that muffling them reduces engine power far more than on a four-stroke engine (high-performance two-stroke engine exhausts are tuned by computing their resonant frequencies, essentially). Finally, they are considered less reliable and durable than four stroke engines.
There are more elaborate possible two-stroke engine configurations, but these often have enough complications that they do not outperform comparable four-stroke engines. New two-stroke designs rely on electronically-controlled fuel injection, oil injection and other design tweaks to reduce pollution and increase fuel efficiency. However, such systems increase the cost of the engines to the point that for small systems simple four-stroke engines are most cost-effective. Many large manufacturers, including Ford and Honda are still actively researching ways to build practical and clean two strokes for automotive use.