Roger T. Howe
Roger T. Howe | |
---|---|
![]() | |
Born | 1957 Sacramento, California, U.S. |
Nationality | American |
Alma mater | Harvey Mudd College University of California, Berkeley |
Known for | MEMS; nanoscale devices; fabrication technology |
Awards | National Academy of Engineering member |
Scientific career | |
Fields | Electrical Engineering |
Institutions | Stanford University |
Thesis | Integrated Electromechanical Vapor Sensor, 1984 |
Doctoral advisor | Richard S. Muller (UC Berkeley) |
Roger Thomas Howe (born 1957 in Sacramento, California) is the William E. Ayer Professor of Electrical Engineering at Stanford University. He earned a B.S. degree in physics from Harvey Mudd College (Claremont, California) and M.S. and Ph.D. degrees in electrical engineering from the University of California, Berkeley in 1981 and 1984, respectively. He was a faculty member at Carnegie-Mellon University in 1984-1985, at the Massachusetts Institute of Technology from 1985-1987, and at UC Berkeley between 1987-2005, where he was the Robert S. Pepper Distinguished Professor. He has been a member of the faculty of the School of Engineering at Stanford since 2005.
His research interests are micro and nanoelectromechanical systems (M/NEMS) design and fabrication. He and his Ph.D. advisor, Richard S. Muller at Berkeley, developed polysilicon surface micromachining technology.[1] [2] This process opened the possibilities of micro mechanical elements such as cantilevers, resonators, and gears. It is currently used for the production of billions of inertial sensors [3] [4] ,[5] microphones ,[6] and timing devices.[7] Polysilicon micromachining technology is still being developed to achieve higher performance sensors .[8] Together with his Ph.D. student, William C. Tang, he co-invented the electrostatic comb drive,[9][10] which is a key building block for microsensors and actuators. With his former colleague Tsu-Jae King Liu and their students, a low-temperature polycrystalline silicon germanium micromachining technology was developed that could be fabricated after standard CMOS electronics.[11] Since joining Stanford, he has contributed to thermionic energy conversion devices[12] and broad-spectrum electronic biomolecular sensors.[13]
He was elected an IEEE Fellow in 1996, for "seminal contributions to microfabrication technologies, devices, and micro-electromechanical systems.” He was co-recipient, with Richard S. Muller, of the 1998 IEEE Cledo Brunetti Award. In 2005, he was elected to the U.S. National Academy of Engineering: "for contributions to the development of microelectromechanical systems in processes, devices and systems." In 2015, he and Yu-Chong Tai were co-recipients of the IEEE Electron Devices Society’s Robert Bosch Micro and Nano Electro Mechanical Systems Award. In 2015, he was also the recipient of the IEEE Electron Devices Society Education Award, “for contributions to mentoring and education in the fields of microelectromechanical systems and nanotechnology.” He co-authored the electronics textbook Microelectronics: an Integrated Approach with Charles G. Sodini of MIT.[14]
From 2011 - 2015, he was the Director of the U.S. National Nanotechnology Infrastructure Network (NNIN) and from 2009 – 2017, he served as the Faculty Director of the Stanford Nanofabrication Facility (SNF).[15]
He co-founded two companies based on research in his group. Silicon Clocks, Inc. was founded in 2004 and was acquired by Silicon Labs, Inc. in 2010. ProbiusDx, Inc. was founded in December 2015 to commercialize a broad-spectrum electronic biomolecular sensor.[16]
References
- ^ R. T. Howe and R. S. Muller, “Polycrystalline Silicon Micromechanical Beams,” Electrochemical Society Spring Meeting, vol. 82-1, Montreal, Québec, Canada, May 9–14, 1982, pp. 184-185.
- ^ R. T. Howe and R. S. Muller, “Polycrystalline silicon micromechanical beams,” Journal of the Electrochemical Society, 130, pp. 1420-1423, (1983)
- ^ http://www.analog.com/media/en/technical-documentation/data-sheets/ADXL335.pdf (accessed Oct. 12, 2018)
- ^ https://www.bosch-mobility-solutions.com/en/products-and-services/industry-elements-and-components/mems-sensors/ (accessed Oct. 12, 2018)
- ^ https://www.st.com/content/st_com/en/about/innovation---technology/mems.html (accessed Oct. 12, 2018)
- ^ https://www.knowles.com/subdepartment/dpt-microphones/subdpt-sisonic-surface-mount-mems
- ^ J. Classen, et al, “Advanced Surface Micromachining Process – a First Step Toward 3D MEMS,” IEEE MEMS Conference, Las Vegas, Nevada, U.S.A, pp. 314-318, Jan. 22-26, 2017.
- ^ E. Ng, et al, “The Long Path from MEMS Resonators to Timing Products,” IEEE MEMS Conference, Estoril, Portugal, pp. 1-2, Jan. 18-22, 2015.
- ^ W. C. Tang and R. T. Howe, “Laterally Driven Resonant Microstructures,” U. S. Patent 5,025,346, June 18, 1991.
- ^ W. C. Tang, T.-C. H. Nguyen, and R. T. Howe, “Laterally driven polysilicon resonant microstructures,” Sensors and Actuators, 20, pp. 25-32 (1989).
- ^ A. E. Franke, J. M. Heck, T. King Liu, and R. T. Howe, “Polycrystalline silicon-germanium films for integrated microsystems,” J. Microelectromechanical Systems, 12, pp. 160-171, (2003).
- ^ J.-H. Lee, et al, “Microfabricated Thermally Isolated Low Work-Function Emitter,” J. Microelectromechanical Systems, 23, pp. 1182-1187 (2014).
- ^ C. Gupta, et al, “Quantum Tunneling Currents in a Nanoengineered Electrochemical System,” Journal of Physical Chemistry C, 121, pp. 15085–15105 (2017).
- ^ R. T. Howe and C. G. Sodini, Microelectronics: an Integrated Approach, Prentice Hall, 1997
- ^ https://cap.stanford.edu/profiles/viewCV?facultyId=10500&name=Roger_Howe
- ^ https://cap.stanford.edu/profiles/viewCV?facultyId=10500&name=Roger_Howe
External links
- Living people
- American electrical engineers
- Stanford University faculty
- Stanford University Department of Electrical Engineering faculty
- Stanford University School of Engineering faculty
- UC Berkeley College of Engineering faculty
- Harvey Mudd College alumni
- UC Berkeley College of Engineering alumni
- 1957 births
- Engineers from California