Ford Barra engine

Ford Barra engine
Overview
Manufacturer	Ford Motor Company of Australia
Production	1 July 2002 – 26 September 2016
Layout
Configuration	Inline-6
Displacement	3,984 cc (243.1 cu in)
Cylinder bore	92.26 mm (3.632 in)
Piston stroke	99.31 mm (3.910 in)
Cylinder block material	Cast iron
Cylinder head material	Aluminium
Valvetrain	DOHC 4 valves per cyl with VCT
Compression ratio	8.47:1 - 12.0:1
Combustion
Fuel system	Multi point fuel injection
Fuel type	Unleaded Autogas
Oil system	Wet sump
Cooling system	Water-cooled
Output
Power output	156–198 kW (209–266 hp) (autogas) 182–195 kW (244–261 hp) (petrol) 240–325 kW (322–436 hp) (turbocharged petrol)
Torque output	374–409 N⋅m (276–302 lb⋅ft) (autogas) 380–391 N⋅m (280–288 lb⋅ft) (petrol) 450–576 N⋅m (332–425 lb⋅ft) (turbocharged petrol)
Chronology
Predecessor	Ford Intech Engine

The Barra is a family of V8 and inline-6 engines used by Ford Australia between 2002 and 2016. The inline-6 engines are unique to the Australian manufactured Falcon and Territory and were developed and manufactured in Geelong, Victoria. The Barra was first introduced in the BA Falcon, named after the "Barramundi" code name used during the development of the BA update engine. The V8 engine, from Essex, Ontario, were discontinued with the FG model, whereas the I6 engines continued production until 26 September 2016, coinciding with the end of production of the Falcon and Territory on 7 October.

Inline 6

All Barra I6 engines are DOHC with VCT and contain 24 valves. They are a development of the SOHC "Intech" I6s produced between 1988 and 2002, which in turn are a development of the 3.3 and 4.1 L push-rod flat-tappet I6, developed in Australia as an "Alloy Head" Crossflow in 1980 , eventually in both carburetted and injected versions, which itself was developed from the original iron-head cross flow engine from 1976, and which in turn was developed, again in Australia, from the original non-cross flow family of light Ford sixes which originated in North America as the "Thriftpower Six" designed for the original American Ford Falcon compact of 1959, initially in just a 144 cubic inch (2.4 L) displacement.

Petrol

Barra 182

This engine is found in the six-cylinder variants of the BA Falcon (also derivative models Fairmont and Fairlane), and SX Territory, and was produced between late 2002 and mid 2005. This was the first Falcon engine that came standard with DOHC and Variable Cam Timing. This contributed to the significant jump in output over the base 157 kW SOHC Intech engine in the previous generation AU Falcon and a 10 kW gain over the Tickford enhanced VCT engine's 172 kW. It also kept Ford's engine power outputs above those of the Holden Ecotec and L67 supercharged V6 engines found in the Holden VY Commodore.

Power: 182 kW (244 hp) @ 5000 rpm

Torque: 380 N⋅m (280 lb⋅ft) @ 3250 rpm

Compression Ratio: 9.7:1

Barra 190

This engine is found in the BF Falcon and SY/SY II Territory, and was produced between late 2005 and early 2008. It is aesthetically the same and mechanically very similar to the Barra 182. Changes from its predecessor include an increase in compression ratio, a slight revision of the cam profiles, a revision of the air intake system, the introduction of dual independent variable camshaft timing, a secondary knock sensor and an upgraded ECU, which allowed for more sophisticated ignition timing and spark control. These changes lead to a slight increase in power to 190 kW.

Power: 190 kW (255 hp) @ 5250 rpm

Torque: 383 N⋅m (282 lb⋅ft) @ 2500 rpm

Compression Ratio: 10.3:1

Barra 195

The Barra 195 is the last version of the naturally aspirated I6 engine and is found in the FG/FG-X Falcon and SZ/SZ II Territory. Changes from its predecessor include a new plastic inlet manifold & throttle body (replacing the broadband manifold intake which originated in the naturally aspirated EF Falcon) and a redesigned cylinder head with 'Fast Burn' swirl changes to the inlet port. These changes achieved power and economy improvements over the Barra 190. The engine also moved to a rear sump design to suit the new FG Falcon front sub-frame.

Power: 195 kW (261 hp) @ 6000 rpm

Torque: 391 N⋅m (288 lb⋅ft) @ 3250 rpm

Compression Ratio: 10.3:1

Turbocharged Petrol

Barra 240T

This engine is found in the BA Falcon XR6 Turbo, and was produced between late 2002 and mid 2005. It is similar to the naturally aspirated Barra 182, except it has different pistons to lower the compression ratio, a single Garrett GT35/40r turbocharger, higher base fuel pressure, Inconel exhaust valves, red rocker cover, and an intercooler.

Power: 240 kW (322 hp) @ 5250 rpm

Torque: 450 N⋅m (332 lb⋅ft) @ 2000-4500 rpm

Compression Ratio: 8.7:1

Barra 245T

Barra 245T in a BF Falcon XR6T engine bay

This engine is found in the BF Falcon XR6 Turbo and the SY Territory Turbo, and was produced between mid 2005 and early 2008. It is internally very similar to its predecessor, with the 5 kW power increase found through the changes introduced by the Barra 190 (revised camshaft profiles and more powerful ECU, enabling dual independent VCT with an extra knock sensor). Aesthetically the engine is the same as the previous model, with the exception of the Territory Turbo using a black rocker cover and a top mounted intercooler. In May 2006, the engine received a minor internal upgrade which addressed concerns of bending con-rods, by introducing stronger con-rods.

Power: 245 kW (329 hp) @ 5250 rpm

Torque: 480 N⋅m (354 lb⋅ft) @ 2000-4500 rpm

Compression Ratio: 8.7:1

Barra 270T (BA / BF FPV)

Barra 270T from a BA-BF FPV

This engine is found in the BA/BF Falcon based FPV F6 Typhoon and Tornado models, and the SY Territory based FPV F6X, and was produced between 2004 and early 2009. It is the high-power variant of the Barra 240/245T versions found in the XR6 Turbo. The increase in power is achieved through the use of higher boost pressures from the otherwise under-utilised large Garrett GT3540 turbocharger, a larger intercooler, revised air intake. These are differentiated from the standard turbo engines by the unique FPV blue-coloured rocker cover. With the introduction of the BF Falcon in 2005, the 270T also inherited the upgrades found in the 245T, but the power figures were left unchanged.

Power: 270 kW (362 hp) @ 5250 rpm

Torque: 550 N⋅m (406 lb⋅ft) @ 2000-4250 rpm

Compression Ratio: 8.7:1

Barra 270T (FG)

This engine is found in the FG/FG-X Falcon XR6 Turbo, and was produced between mid 2008 and late 2016. Although the power figures for the revised turbo engine mimic the old FPV turbo I6, the engines are quite different. It has a redesigned low-profile log style intake manifold, a smaller turbocharger which spools faster, a new intercooler, redesigned pistons to increase compression. The end result is that the FG XR6 Turbo is faster than the FPV's BF Typhoon although they share the same power output. This engine introduces a transient over-boost feature for a maximum of 10 seconds when optimal atmospheric conditions are met when under full throttle, which increases torque to a maximum of 586 Nm.

Power: 270 kW (362 hp) @ 5250 rpm

Torque: 533 N⋅m (393 lb⋅ft) @ 2000-4750 rpm

Compression Ratio: 8.8:1

Barra 310T

This engine is found in the FG Falcon based FPV F6. It is the high-power variant of the FG XR6 Turbo's Barra 270T. It was produced between mid 2008 and mid 2014, ending production when FPV shut down. Featuring a larger turbocharger and intercooler, different pistons to reduce compression, and larger injectors than its less powerful sibling (the FG Barra 270T), it was the first engine manufactured in Australia to produce more than 100 hp (75 kW) per litre, producing 310 kW at the flywheel.

Power: 310 kW (416 hp) @ 5500 rpm

Torque: 565 N⋅m (417 lb⋅ft) @ 1950-5200 rpm

Compression Ratio: 8.47:1

Barra 325T

The final and most powerful variant of the Barra engine featured in the FG-X XR6 Sprint. This engine is the most powerful six cylinder produced in Australia and was built in very limited numbers, with only 500 for Australia and 50 for New Zealand (True production is 560, as 10 pre-production vehicles were built and auctioned off). Each engine had its own numbered build plaque attached to the rocker cover, which is painted in the same colour as the Territory Turbo rocker cover. The engine is based internally upon the Barra 270T, with extras added from the Barra 310T variant such as the turbo, intercooler and injectors. In an Australian first, Ford also employed a custom designed carbon fibre air intake which increased airflow by 45 percent. It was chosen to base the engine on the 270T instead of the 310T due to the increased compression ratio. The engine yet again employs Ford's over-boost feature, which when the correct conditions are met will increase engine output to 370 kW and 650 Nm.

Power: 325 kW (436 hp) @ 6000 rpm

Torque: 576 N⋅m (425 lb⋅ft) @ 2750 rpm

Compression Ratio: 8.8:1

Internals

According to Ford Chief Program Engineer David Burn and Program Manager Justin Capicchiano, there are differences in the internals between turbo models, however no forged internals have been used.

Liquefied Petroleum Gas

Barra E-Gas

This engine was launched in 2002 with the BA Falcon and was a development of the Intech E-Gas engine. The E-Gas engine is designed to run on autogas only. It features a low-performance, high-reliability, low-maintenance Vialle closed-loop single-point venturi-style LPG-injector-less carburetion system in lieu of the standard sequential petrol injection system. This engine was carried over to the FG Falcon with only one option of a 4-Speed automatic transmission, without traction control but was replaced in mid-2011 by the EcoLPi system, which featured the ZF 6HP26 6-speed automatic transmission and traction control as per fitted to the petrol models.

Power: 156 kW (209 hp) @ 4750-5000 rpm

Torque: 374 N⋅m (276 lb⋅ft) @ 2750-3000 rpm

Compression Ratio (BA E-Gas): 10.7:1

Compression Ratio (BF / FG E-Gas): 10.3:1

Barra EcoLPi

This engine was launched in 2011 as a replacement for the E-Gas engine. It features a liquid phase injection autogas system, allowing for much higher power and torque than previously.

Power: 198 kW (266 hp) @ 5000 rpm

Torque: 409 N⋅m (302 lb⋅ft) @ 3250 rpm

Compression Ratio: 12.0:1

Discontinuation

On the 23rd of May 2013, Ford Australia confirmed that the Barra engine would be discontinued along with the Ford Falcon and Territory by October 2016. Ford Australia's engine manufacturing operations ceased on 26 September 2016 and car assembly on 7 October 2016. Ford Australia president Bob Graziano cited unprofitability due to high labour costs and dwindling market share for the demise of local manufacturing.

V8

Barra 220

The Barra V8s, manufactured at the Essex, Ontario, Canada engine plant, are based on the Ford modular engine. All have a displacement of 5.4 litres and are SOHC with VCT incorporating three valves per cylinder. The Falcon was the first vehicle in the Ford world to have the VCT Modular engine.

The Barra V8 line is the V8 5.4 L upgrade for the all Falcon models excluding the XR (XT, Futura, Fairmont, Fairmont Ghia, Fairlane, Fairlane Ghia, LTD). The higher-performance V8s in the Falcon range (XR8 / FPV GT) were known as the Boss 260/290/302/315 and differ from the Barra V8 engine as they are DOHC with four valves per cylinder.
Common specifications to Barra V8s
Bore: 90.2 mm
Stroke: 105.8 mm
Displacement: 5408 cc
Number of valves: 24

Barra 220

This was an optional engine on the BA Falcon and was produced between 2002 and 2005.

Power: 220 kW (295 hp) @ 4750 rpm

Torque: 472 N⋅m (348 lb⋅ft) from 3250-4000 rpm

Barra 230

An option on the BF Falcon, its extra power comes from a slight increase in compression ratio. This is done safely with the addition of another knock sensor. It was in production from 2005 until the release of the FG Falcon.

Power: 230 kW (308 hp) @ 5350 rpm

Torque: 500 N⋅m (369 lb⋅ft) @ 3500 rpm

See also

• Undersquare
• Ford of Australia modern V8s

External links

• Ford Australia