Search results
The page "Soldered seam" does not exist. You can create a draft and submit it for review or request that a redirect be created, but consider checking the search results below to see whether the topic is already covered.
remaining solder types are used in decreasing order of hardness during the process of making an item, to prevent a previously soldered seam or joint desoldering...38 KB (4,923 words) - 17:09, 27 April 2024
the item to be soldered. Another method for soldering is to place solder and flux at the locations of joints in the object to be soldered, then heat the...64 KB (8,893 words) - 06:59, 19 May 2024
and seams. Continuous, long runs of soldered seams can cause stress fractures and should therefore be avoided. Common 50-50 tin-lead bar solder is often...91 KB (10,970 words) - 07:11, 23 December 2023
Solder is a metallic material that is used to connect metal workpieces. The choice of specific solder alloys depends on their melting point, chemical...69 KB (1,860 words) - 19:47, 24 May 2024- silver. Bore anomalies include (but are not limited to) imperfectly soldered seam tubing and telescoping joints. Each of the five joints — crook or bit...10 KB (1,411 words) - 07:23, 11 April 2024
are made from aluminum. Early cans were often soldered with neurotoxic high-lead solders. High-lead solders were banned in the 1990s in the United States...55 KB (5,921 words) - 17:13, 11 May 2024
extremely unsatisfactory during the North African Campaign. The crimped or soldered seams easily split during transport, especially off-road over the rock-strewn...22 KB (2,534 words) - 15:20, 27 April 2024- Electric resistance welding (redirect from Seam welding)the weld and the method of applying pressure to the joint: spot welding, seam welding, flash welding, projection welding, for example. Some factors influencing...14 KB (1,957 words) - 06:37, 19 May 2024
heated in small furnaces, covered in Sal ammoniac, and then used for soldering seams.[full citation needed] Tinwares were being produced in London by the...8 KB (974 words) - 13:23, 27 May 2024
a "good effort". The problem with the containers was the crimped or soldered seams, which easily split during transportation, especially over the rocky...4 KB (432 words) - 13:01, 2 July 2023
plus a thick gold layer, except where the leads are soldered and decoupling capacitors are soldered on top of the package. These packages are hermetic...9 KB (1,158 words) - 05:03, 21 April 2024
Canning (section Sealing: double seams)seams is the welded side seam. Prior to the welded side seam, the can body was folded and/or soldered together, leaving a relatively thick side seam....35 KB (4,142 words) - 12:57, 22 January 2024- as the solder cools. In contrast, when lead-tin mixtures were used to solder seams in automobile bodies a pasty state enabled a shape to be formed with...15 KB (1,855 words) - 01:00, 12 April 2024
interlocking the can body and a can end (or lid). Originally, the can end was soldered or welded onto the can body after the can was filled. However, this introduced...10 KB (1,405 words) - 02:23, 24 April 2023
Metal roof (redirect from Standing seam metal roof)that roof. Mechanically seamed roofs are seamed together using a roof seamer and can be either single lock or double lock seamed, meaning they can be folded...21 KB (2,522 words) - 18:04, 26 May 2024- roofs of low pitch such as 0.5/12 to 3/12 pitch. Flat-seam metal with or without soldered seams. Steel coated with a coloured alloy of zinc and aluminium...16 KB (2,066 words) - 22:07, 14 March 2024
tinplate, had a visible tin solder seam, and incorporated an opening strip. A key for use on the opening strip was soldered to the base of every B unit...26 KB (3,803 words) - 15:04, 19 November 2023
Pipe (fluid conveyance) (section Soldered connections)side of the replacement fitting. Whereas with a soldered fitting, a defective joint can just be re-soldered, or heated and turned if a minor change is required...42 KB (6,031 words) - 20:44, 29 March 2024
Piping and plumbing fitting (section Soldering)durable than soldered (aka sweated) connections, they are easy to install with simple tools. However, they take longer to install than soldered joints and...56 KB (6,854 words) - 21:49, 27 March 2024
then all the components on the circuit board could be soldered at one time on a wave soldering machine and passed on to automated testing machines, with...23 KB (3,249 words) - 00:05, 17 February 2024
- day for making this class of tube. Seamed tubes, especially of copper and brass, are made by brazing or soldering the edges of the skelp. Another method
- [imitating Mulcahy] "Left, right! Left, right! Little finger along the seams of yer trousers!" [normally] Marching is probably all they'll ever get to
- with an integral frame. Plastic bubble skylights tend to leak because the seam between the roof and the bubble expands and contracts over time. Pre-framed