Jump to content

ADM-3A

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by Guy Harris (talk | contribs) at 01:42, 28 September 2018 (→Hardware: Permanently dead, perhaps, but fixable.). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

ADM-3A
DeveloperLear Siegler

The ADM-3A was an early video display terminal introduced in 1976.[1] It was manufactured by Lear Siegler and had a 12 inch screen displaying 12 or 24 lines of 80 characters. It set a new industry low single unit price of $995. Its "dumb terminal" nickname came from some of the original trade publication advertisements.[2] It quickly became commercially successful because of the rapid increase of computer communications speeds, and because of new minicomputer systems released to the market which required inexpensive operator consoles.

Antecedents

Lear Siegler, Inc. (LSI) manufactured its first video display terminal in 1972 – the 7700A.

In 1973 LSI hired a new head of engineering, Jim Placak. He and his team created the ADM-1 in late '73. It set a new pricing low in the industry at $1,500. Its lower cost was primarily due to a unique single printed circuit board design. In early 1973 the LSI division in Anaheim, California that manufactured these and other products hired a management team for this product line – a VP, national sales manager, and one regional sales manager – for the western region. The regional manager was Dennis Cagan who came from an LSI competitor. The ADM-1 was followed by the ADM-2 in early '74. It had expanded functionality and a detached keyboard. It set another new industry low single unit price of $1,195.[citation needed]

The initials "ADM" were referred to as meaning "American Dream Machine" in some advertising.[3]

ADM-3

The clam shell ADM-3 followed and the first manufactured units were introduced at 1975 National Computer Conference in Anaheim, Calif., May 19-22, 1975, in booth 2348 at a price of $995.[4][2] Its innovative wave soldered single board design, which included the keyboard and all connectors, was packaged in an original clam shell enclosure.

Within weeks of the launch of the ADM-3, Cagan started to book very large orders. Its 'Dumb Terminal' nickname came from some of the original trade publication ads, and quickly caught on industry wide.[2] Due to two emerging trends the device immediately became the best selling in the industry. Computer communications speeds were rapidly increasing, and a wave of general purpose and dedicated single application minicomputer systems were hitting the market from dozens of manufacturers. These required inexpensive operator consoles that could match the speeds. With no fast low cost printers available, the ADM-3 (painted in a variety of custom colors for the OEMs) became the de facto standard. By December 20, 1976 Teletype Model 33 KSR were $895 or $32/month and ADM-3 were $995 or $36/month.[5]

ADM-3 options

The original ADM-3 terminal only displayed capital letters.[6] In 1976, an option was added to allow it to display both lower and upper case.[6][7] The standard version of the terminal displayed only twelve (rather than twenty-four) rows of eighty characters.[2][6] In those days RAM was expensive, and halving the display size halved the RAM requirement[8] (and likewise all uppercase required only six bits per character to be stored rather than seven). Further optional add-ons included a graphics card enabling it to emulate a Tektronix 4014[citation needed] and an extension port which would allow daisy chaining several ADM-3As on a single RS-232 line.[2]

ADM-3A

In 1976, the ADM-3A was introduced.[1] The ADM-3A added support for control codes to move the cursor around on the screen, and directly position the cursor at any point in the display. It did not, however, support “clear to end of line” or “clear to end of screen”, or other more advanced codes that appeared in later terminals, such as the VT52 and VT100.

The ADM-3A's overall setup was controlled by 20[6][9] DIP switches under the nameplate at the front of the machine, beside the keyboard, including speed from 75 to 19,200 baud. The advanced configuration options allowed split speed connection, sending at one rate, and receiving at another.

Hardware

ADM-3A keyboard layout

The 5×7 dot matrix characters were displayed in amber, green, or white phosphor on black (the cursor was 7×9). The keyboard had 59 keys. The 12-inch monochrome CRT[10] was mounted in the top half of the case, which was hinged in the back and opened like a clamshell. The CRT was typically made by Ball Brothers.[citation needed]

Unlike later terminals, such as the VT100, the ADM-3A did not use a microprocessor in its implementation, but instead used TTL.[9] It did, however, use RAM chips, rather than the Circulating Memory used by earlier terminals, such as the Datapoint 3300.

Legacy

The use of the HJKL keys for moving the cursor in the vi editor and its descendants stems from the ADM-3A; it had the cursor-movement arrows printed on those four keys.[11][discuss]

Both the arrows and the "home" correspond to the functions of the corresponding control characters Ctrl+H, Ctrl+J, Ctrl+K, Ctrl+L, and Ctrl+^ (identical to Ctrl+~) when sent to the terminal, moving the cursor left, down, up, right, and to the "home" position in the upper left-hand corner of the terminal, respectively.[12] (The Ctrl+H and Ctrl+J functions were standard, but the interpretations of Ctrl+K, Ctrl+L, and Ctrl+^ were new to the ADM-3A.)

The tilde key was additionally labeled HOME, which is why ~ is used to mean home directory in many Unix shells .[discuss]

Finally, the control key was located above, not below, the shift key—in the same place where most modern PC keyboards put the Caps Lock key.[13] Many standard Unix key combinations were designed with the QWERTY layout and the ADM-3A's original Ctrl key placement in mind.[citation needed] Many of those key combinations are still in use today, even on non-Unix operating systems. Seasoned computer users familiar with the original layout often claim that the different position of the Ctrl key on modern PC keyboard layouts makes the use of Ctrl key combinations more cumbersome.[14][15][16][better source needed] Solutions exist for many operating systems to switch around the Caps Lock and Ctrl keys in software,[15][17] thus making the PC keyboard layout more closely resemble the ADM-3A's keyboard layout.

See also

References

  1. ^ a b "Lear Siegler Updates ADM-1, Gives ADM-3 Full Cursor Ability". Computerworld. July 5, 1976. Retrieved July 13, 2016.
  2. ^ a b c d e "Introducing The $995 Dumb Terminal".
  3. ^ "Lear Siegler advertisement Computerworld 21 May 1984". Terminals Wiki. Classic cmp. Retrieved 21 July 2016.
  4. ^ "Compact ADM-3 Parading". Computerworld. May 14, 1975.
  5. ^ https://books.google.com/books?id=Zab9x-fFopsC&pg=PA15&dq=adm-3+33-ksr
  6. ^ a b c d "ADM-3 Maintenance Manual" (PDF).
  7. ^ "Lower Case Feature Available for ADM-3". Computerworld. March 29, 1976.
  8. ^ ADM-3A Lower Case Option "Clone"
  9. ^ a b "ADM-3A Maintenance Manual" (PDF).
  10. ^ "ADM-3A CRT Replacement". Archived from the original on October 20, 2016.
  11. ^ ADM-3A Operators Manual
  12. ^ "Tenth Anniversary ADM 3A Dumb Terminal Video Display Terminal User's Reference Manual" (PDF). Lear Siegler, Inc. April 1986. pp. 1–5.
  13. ^ Very early PC keyboards also had the Ctrl key located above the shift key, just like the ADM-3A's keyboard.[citation needed]
  14. ^ http://capsoff.org/history
  15. ^ a b http://c2.com/cgi/wiki?RemapCapsLock
  16. ^ http://www.emacswiki.org/emacs/MovingTheCtrlKey
  17. ^ "Swapping Capslock and Control Keys". Archived from the original on 2011-02-25. {{cite web}}: Unknown parameter |deadurl= ignored (|url-status= suggested) (help)
Wikimedia Commons has media related to ADM-3A.
Retrieved from "https://en.wikipedia.org/w/index.php?title=ADM-3A&oldid=861521769"