Coaxial power connector

Most common coaxial power connector, male and female, 5.5 x 2.5 mm

Common DC power connectors

A coaxial power connector is an electrical power connector used for attaching extra-low voltage devices such as consumer electronics to external electricity. Also known as barrel connectors, concentric barrel connectors or tip connectors, these small cylindrical connectors come in an enormous variety of sizes.

Barrel plug connectors are commonly used to interface the secondary side of a power supply with the device. Some of these jacks contain a normally closed switch; the switch can disconnect internal batteries whenever the external power supply is connected.

Connector construction and terminology

Female (plug)

On the female plug, the outer body is metallic and cylindrical in shape, and comprises one of the two contacts. The second, inside contact is a hollow metallic cylinder constructed to accept insertion of the pin in the corresponding male connector. The inner and outer barrels are separated by an insulating layer. The outer contact is generally called the barrel, sleeve or ring, and the inner contact is called the tip.

Male (receptacle)

There is typically a single spring-loaded contact at the side of the male connector and a pin in the center corresponding to the intended female plug.

Connector sizes

There are many different sizes of coaxial power connectors (see table at end of this article).

Contact ratings commonly vary from unspecified up to 5 amperes (11 amperes for special high-power versions). Voltage is often unspecified, but may be up to 48V with 12V typical. The smaller types usually have lower current and voltage ratings.

It is quite possible that new sizes will continue to appear and disappear. One possible reason that a particular manufacturer may use a new size is to discourage use of third-party power supplies, either for technical reasons or to promote use of their own products, or both.

The sizes and shapes of connectors do not consistently correspond to the same power specifications across manufacturers and models. Two connectors from different manufacturers with different sizes could potentially be attached to power supplies with the same voltage and current. Alternatively, connectors of the same size can be part of power supplies with different voltages and currents. Use of the wrong power supply may cause severe equipment damage, or even fire.

Common sizes and interchangeability

Some common DC power connectors

Generic plugs are often described by their inside diameter, such as 2.1mm DC plugs and 2.5mm DC plugs.

After the two common 5.5mm OD plugs, the next-most common size is 3.5mm OD with a 1.3mm ID, usually about 9.5mm in length, although both longer and shorter versions also exist. These 3.5mm OD plugs are normally used for lower voltages and currents.

Locking and retention features

A ring-shaped 'locking detent' or 'high-retention feature', present on the barrel of some DC coaxial connectors, is a feature intended to prevent accidental disconnection. Typically, this feature is a conical cut-back section of the tip, just behind the insulator that separates the inner from outer contact surfaces.

'lock-ring DC coaxial connector' uses a captive threaded ring or collar to secure the connection between the plug and jack. This design offers strong resistance to unplugging when used properly.

Lock-ring DC coaxial connectors. The knurled barrel allows the plug to be secured to jacks that have mating male threads.

'lock-tab DC coaxial connector' (also called 'bayonet lock') offers a compromise that resists unplugging, but which will disengage when pulled hard enough. This connector uses small metal tab protrusions on the connector barrel to lock the plug in place, requiring a special push-and-rotate motion to engage the locks.

Standards

Close-up of a yellow-tipped EIAJ connector. Note 2 round adapter pins on the opposite end.

There are several standards in existence, such as IEC, EIAJ in Japan and DIN in Germany. More recently, some manufacturers appear to have implemented their own system correlating voltage and plug size. In addition, there appears to be a trend to standardize DC connector to negative barrel (or sleeve) of a coaxial power connector.

IEC 60130-10

IEC 60130-10:1971 defines five DC power connectors.

• Type A: 5.5 mm OD, 2.1 mm ID (with optional screw lock)
• Type A: 5.5 mm OD, 2.5 mm ID (with optional screw lock)
• Type B: 6.0 mm OD, 2.1 mm ID
• Type B: 6.0 mm OD, 2.5 mm ID
• Type C: 3.8 mm OD, 1.4 mm ID
• Type D: 6.3 mm OD, 3.1 mm ID
• Type E: 3.4 mm OD, 1.3 mm ID

EIAJ power connectors

Further information: EIAJ connector

Five plug and matching socket or jack designs are defined by the EIAJ standard RC-5320A (also called JEITA RC-5320A). Each of these plugs is used with a specified voltage range. Most manufacturers use a yellow insulating material to distinguish these plugs from other similar-looking DC plugs.

• EIAJ-01 for 0–3.15 V
• EIAJ-02 for 3.15–6.3 V
• EIAJ-03 for 6.3–10.5 V
• EIAJ-04 for 10.5–13.5 V (also called JSBP 4)
• EIAJ-05 for 13.5–18 V (also called JSBP 5)

EIAJ-04 and 05 have an internal male pin in the plug. The 01 through 03 sizes do not and are similar to the generic plugs in structure. These five EIAJ plugs are 9.5 mm in length and have a current rating of 2A.

There are two other, less common, connectors defined by EIAJ; RC-5321 and RC-5322. The latter is designed for both 12 V and 24 V automotive applications.

DIN 45323

The German national standards organization DIN (Deutsches Institut für Normung — German Institute for Standardization) issued DIN 45323, which defines two DC power plug and jack (respectively) sizes. At least one of these sizes has a maximum rating of 34 V and 3 A. The information here is inferred from catalog references, as the German standard has not been translated into English yet.

• 5.00 mm OD, 2.00 mm ID, 14 mm long?
• 6.00 mm OD, 1.98 mm ID

Listing of DC coaxial connectors

This list attempts to show all known sizes, and is annotated with some manufacturers producing selected types, since each manufacturer makes its own unique subset of the known types. Note that the example part numbers given may have different connector barrel (sleeve) lengths, and are not necessarily exact equivalents. There are many more design variants than can be listed in this table, so only a small sampling of part numbers is given.

Connector size is often listed in the format OD (outer diameter) x ID (inner diameter) x L (length of barrel and expressed in millimeters). Designations may vary between manufacturers.

Coaxial plugs that have a male center pin will have another measurement, Center Pin Diameter (CPD). These plugs are often used for higher power applications such as portable computers.

There are a number of sizes listed below that appear to be quite similar, and while the tolerances of these connectors are typically indicated as ±0.05 or ±0.03 mm by the manufacturers, there is still ambiguity as to whether two sizes differing by only 0.05 mm (or where the specification is only given to the nearest 0.10 mm) warrants listing them separately here.

OD (mm)	ID (mm)	CPD (mm)	Barrel length (mm)	Adaptaplug	Standard	Volts	Plug part numbers	Jack part numbers	Notes
2.00	0.60								used in newer Nokia phones (AC-3)
2.35	0.70		9.5	A	EIAJ-01	0–3.15 V	Kobiconn 3218-EX Lumberg 1636 01	Kobiconn 0307-EX (inline)	Canon ACK-800, also used on very old Motorola phones (SPN4364/4365/4366/4474)
2.40	0.70						Egston 212		possibly a rounded-off representation of EIAJ-01
2.40	0.80						Egston 213
2.50	0.80								Used in Samsung Bluetooth headsets and few tablet PCs
3.00	1.00
3.00	1.10			G			CUI Inc. PP-019 Egston 214
3.20	0.90						CUI Inc. PP-017
3.30	1.00							Motorola AAPN4064A	Used in older Motorola phones (SPN4680/4681/4682/4677/5296A) and also used in some rare Nokia phones (ACH-6)
3.40	1.30			H			Kobiconn 3210-E	Kobiconn 0309-EX (inline)
3.40	1.35						Egston 218 Medical, 220
3.40	1.40						Lumberg NES/J 135
3.50	0.90							possible nokia acp-7 charger	used in many older Nokia phones (ACP-12?)
3.50	1.10						CUI Inc. PP3–002C Philmore 202
3.50	1.30						Egston 238 Philmore 204,2049	Kobiconn 0308-EX (inline) Philmore 256 (inline)	Also used in older Alcatel phones (3DS07008A?AA, 3DS09371A?AA, 3DS10628A?AA)
3.50	1.35						CUI Inc. P7 CUI Inc. PP3–002D Egston 215 Kobiconn PA35135-E
3.60	1.15						Egston 216
3.80	1.10			I			CUI Inc. P9 but with 1.05 mm ID
3.80	1.30						Egston 217
3.80	1.35						CUI Inc. P8
4.00	1.70		9.5	B	EIAJ-02	3.15–6.3 V	Kobiconn 3219-EX Lumberg 1636 02	Kobiconn 0311-EX (inline)
4.75	1.70		9.5	C	EIAJ-03	6.3–10.5 V	Kobiconn 3220-EX Lumberg 1636 03	Kobiconn 0310-EX (inline)
4.75	?.??		2.5 protruding	C	EIAJ RC-5321
5.00	1.50			J
5.00	2.00				DIN 45323?		Egston 206,207,219
5.00	2.10			K			CUI Inc. P3
5.00	2.50			L			CUI Inc. P4
5.50	1.50			S
5.50	2.10			M			CUI Inc. P5 CUI Inc. PP3–002A Kobiconn 3217-EX Philmore 210, 210L, 2109 Switchcraft S-760, S-765	CUI Inc. PR-002A (inline) Kobiconn 0302 (inline) Philmore 257 (inline) Switchcraft 722A (panel)	2.1 mm center pin Common on guitar effect pedals
5.50	2.10						CUI Inc. P10 Kobiconn 7391 Philmore 2560 Switchcraft S760K		2.1 mm center pin, lock-ring
5.50	2.10						Kobiconn 0721-EX	Kobiconn 1000-EX (panel)	2.1 mm center pin, lock-tab
5.50	2.50			N			CUI Inc. P6 CUI Inc. PP3–002B Egston 222 Kobiconn 0702-EX Philmore 250, 250L, 2509 Switchcraft 760, 765	CUI Inc. PR-002B (inline) Kobiconn 0303 (inline) Philmore 258 (inline) Switchcraft 712A (panel)	2.5 mm center pin
5.50	2.50						CUI Inc. P11 Kobiconn 7395 Philmore 2560 Switchcraft 760K		2.5 mm center pin, lock-ring
5.50	2.50						Kobiconn 0725-EX	Kobiconn 1100-EX (panel)	2.5 mm center pin, lock-tab
5.50	2.80			O
5.50	3.0					5V, 1.5A, Efficiency Level V	Philmore Coaxial Power Plug 3.0mm I.D./5.5mm O.D. No. 206		Roku 2 XS HDTV Streaming Box
5.50	3.30	1.00	9.5	D	EIAJ-04, JSBP4	10.5–13.5 V	Lumberg 1636 04		Microsoft Xbox 360 HD DVD drive
5.50	3.80	1.80		P
6.00	1.98				DIN 45323		Lumberg 1632 01
6.30	3.00			Q
6.50	?.??				EIAJ RC-5322
6.50	3.00								Used in Yamaha keyboard power supply
6.50	3.10	1.00					Philmore 285
6.50	3.40	1.40	9.0			18 VDC @5A	Kobiconn 6014-E		used often for laptop computers
6.50	4.10	1.00			JEITA RC-5322	24 VDC @ 2A	Lumberg 1636 06		Epson Photo Scanners V600 etc
6.50	4.30	1.40		T	EIAJ-05, JSBP5	13.5–18.0 V	Lumberg 1636 05		OD is of ring at tip
6.90	4.20	0.70		R
7.00	??	1.00					Philmore 48-412
7.4	5.5	0.5	12.5						Some Asus, some Dell, Sony laptops

RadioShack Adaptaplug

RadioShack sold a line of adapter plugs for universal AC adapters. Each "Adaptaplug" had a single-letter code, but did not provide any other official designation, nor publish the complete specifications and tolerances on barrel and pin dimensions. RadioShack's web site listed the diameters to the nearest 0.1 mm, and sometimes differs slightly from the official EIAJ RC-5320A standard dimensions. This list may include some parts RadioShack has discontinued but are retained here for completeness.

Adaptaplug	Outside diameter	Inside diameter	Pin diameter	Standard type	Voltage range	Ring color	Radio Shack part number
A	2.3 mm	0.7 mm		EIAJ-01	< 3.15 V	Yellow	3807936
B	4.0 mm	1.7 mm		EIAJ-02	3.15 – 6.3 V	Yellow	3780266
C	4.7 mm	1.7 mm		EIAJ-03	6.3 – 10.5 V	Yellow	3780267
D	5.5 mm	3.3 mm	0.9 mm	EIAJ-04	10.5 – 13.5 V	Yellow	3780268
E	2.5 mm (3/32" submini plug)					Black	3870005
F	3.5 mm (1/8" mini plug)					Black	3875411
G	3.0 mm	1.1 mm				Turquoise	3807935
H	3.4 mm	1.3 mm		IEC 60130-10 Type E		Orange	3870006
I	3.8 mm	1.1 mm		IEC 60130-10 Type C		Pink	3870007
J	5.0 mm	1.5 mm				Red	3870004
K	5.0 mm	2.1 mm				Purple	3807937
L	5.0 mm	2.5 mm				Dark Green	3807938
M	5.5 mm	2.1 mm		IEC 60130-10 Type A		Navy	3807939
N	5.5 mm	2.5 mm		IEC 60130-10 Type A		White	3807940
O	5.5 mm	2.8 mm				Brown	3780269
P	5.5 mm	3.8 mm	1.8 mm			Not Specified	3802153
Q	6.3 mm	3.0 mm				Yellow-Green	3780270
R	6.9 mm	4.2 mm	0.7 mm			Not Specified	3912655
S	5.5 mm	1.5 mm				Gray	3875405
T	6.5 mm	4.3 mm	1.4 mm	EIAJ-05	13.5 – 18.0 V	Yellow	3875406
U	6.5 mm	4.1 mm / 3.10 mm	1.0 mm	IEC 60130-10 Type D?		Light Yellow	3875407

See also

• AC adapter
• EIAJ connector
• Cigarette lighter receptacle
• DC connector
• Anderson Powerpole

External links

• Guide to Understanding Power Conversion, RadioShack

Datasheets (drawings and dimensions)

• CUI
• Hosiden
• Lumberg
• SMK
• West Side