EVEX prefix

The EVEX prefix (Enhanced vector extension) and corresponding coding scheme is an extension to the 32-bit x86 (IA-32) and 64-bit x86-64 (AMD64) instruction set architecture. EVEX is based on, but should not be confused with the MVEX prefix used by the Knights Corner processor.

The EVEX scheme is a 4-byte extension to the VEX scheme which supports the AVX-512 instruction set and allows addressing new 512-bit ZMM registers and new 64-bit operand mask registers.

Features

EVEX coding can address 8 operand mask registers, 16 general-purpose registers and 32 vector registers in 64-bit mode (otherwise, 8 general-purpose and 8 vector), and can support up to 4 operands.

Like the VEX coding scheme, the EVEX prefix unifies existing opcode prefixes and escape codes, memory addressing and operand length modifiers of the x86 instruction set .

The following features are carried over from the VEX scheme:

• Direct encoding of three SIMD registers (XMM, YMM, or ZMM) as source operands (MMX or x87 registers are not supported);
• Compacted REX prefix for 64-bit mode;
• Compacted SIMD prefix (66H, F2H, F3H), escape opcode (0FH) and two-byte escape (0F38H, 0F3AH);
• Less strict memory alignment requirements for memory operand

EVEX also extends VEX with additional capabilities:

• Extended SIMD register encoding: a total of 32 new 512-bit SIMD registers ZMM0-ZMM31 in 64-bit mode;
• Operand mask encoding: 8 new 64-bit opmask registers k0-k7 for conditional execution and merging of destination operands;
• Broadcasting from source to destination for instructions that take memory vector as a source operand: the second operand is broadcast before being used in the actual operation;
• Direct embedded rounding control for instructions that operate on floating-point SIMD registers with rounding semantics;
• Embedded exceptions control for floating-point instructions without rounding semantics;
• Compressed displacement (DISP8*N), new memory addressing mode to improve encoding density of instruction byte stream; the scale factor N depends on vector length and broadcast mode.

For example, the EVEX encoding scheme allows conditional vector addition in the form of

VADDPS zmm1 {k1}{z}, zmm2, zmm3

where {k1} modifier next to the destination operand encodes the use of opmask register k1 for conditional processing and updates to destination, and {z} modifier (encoded by EVEX.z) provides the two types of masking (merging and zeroing), with merging as default when no modifier is attached.

Technical description

The EVEX coding scheme uses a code prefix consisting of 4 bytes; the first byte is always 62h and derives from an unused opcode of the 32-bit BOUND instruction, which is not supported in 64-bit mode.

EVEX Prefix in the AVX-512 Instruction Format

# of bytes	4	1	1	1	4 / 1	1
[Prefixes]	EVEX	Opcode	ModR/M	[SIB]	[Disp32] / [Disp8*N]	[Immediate]

The ModR/M byte specifies the addressing of the source register with mod and r/m fields, which encode either 8 registers or 24 addressing modes, and the destination register is encoded with reg field. Base-plus-index and scale-plus-index addressing require the SIB byte, which encodes 2-bit scale factor as well as 3-bit index and 3-bit base registers. In certain SIB encodings, Disp32 contains displacements that need to be added to the base address.

The EVEX prefix retains some fields introduced in the VEX prefix:

• Four bits R, X, B, and W from the REX prefix. W expands the operand size to 64 bits or serves as an additional opcode, R expands reg, B expands r/m or reg, and X and B expand index and base in the SIB byte. Comparing to the VEX prefix, RXB are provided in non-inversed forms.
• Four bits named v, specifying a second non-destructive source register operand.
• Bit L specifying 256-bit vector length.
• Two bits named p to replace operand size prefixes and operand type prefixes (66, F2, F3).
• Two of the m bits for replacing existing escape codes (0F, 0F 38 and 0F 3A;).
• Bit V' is an additional source register index.

New functions of the existing fields:

• Bit X now expands r/m along with bit B when the SIB byte is not present, which allows 32 SIMD registers.

There are several new bit fields:

• Three bits named a, specifying the operand mask register (k0-k7) for vector instructions.
• Bit z for specifying merging mode (merge or zero).
• Bit b for source broadcast, rounding control (combined with L’L), or suppress exceptions.
• Bit L’ for specifying 512-bit vector length, or rounding control mode when combined with L.
• Bit R’ for expanding reg, which allows for 32 SIMD registers.

The encoding of the EVEX prefix is as follows:

	7	6	5	4	3	2	1	0
Byte 0 (62h)	0	1	1	0	0	0	1	0
Byte 1 (P1)	R	X	B	R’	0	0	m1	m0	P[7:0]
Byte 2 (P2)	W	v3	v2	v1	v0	1	p1	p0	P[15:8]
Byte 3 (P3)	z	L’	L	b	V’	a2	a1	a0	P[23:16]

The following table lists allowed register addressing combinations (bit 4 is always zero when encoding the 16 general purpose registers):

Register addressing in 64-bit mode using EVEX prefix

Addressing mode	Bit 4	Bit 3	Bits [2:0]	Register type	Common usage
REG	EVEX.R’	EVEX.R	ModRM.reg	General purpose, Vector	Destination or Source
NDS/NDD	EVEX.V’	EVEX.v3v2v1v0		GPR, Vector	2nd Source or Destination
RM	EVEX.X	EVEX.B	ModRM.r/m	GPR, Vector	1st Source or Destination
BASE	0	EVEX.B	ModRM.r/m	GPR	Memory addressing
INDEX	0	EVEX.X	SIB.index	GPR	Memory addressing
VIDX	EVEX.V’	EVEX.X	SIB.index	Vector	VSIB memory addressing
IS4	Imm8[3]	Imm8[7:4]		Vector	3rd Source