Host controller interface (USB, Firewire)
This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these messages)
|
A host controller interface (HCI) is a register-level interface that enables a host controller for USB or FireWire hardware to communicate with a host controller driver in software. The driver software is typically provided with an operating system of a personal computer, but may also be implemented by application-specific devices such as a microcontroller.
On the expansion card or motherboard controller, this involves much custom logic, with digital logic engines in the motherboard's controller chip, plus analog circuitry managing the high-speed differential signals. On the software side, it requires a device driver (called a Host Controller Driver, or HCD).
FireWire
Open Host Controller Interface
Open Host Controller Interface (OHCI) , is an open standard.
When applied to a FireWire (IEEE 1394) card, OHCI means that the card supports a standard interface to the PC and can be used by the OHCI FireWire drivers that come with all modern operating systems. Because the card has a standard OHCI interface, the OS does not need to know in advance exactly who makes the card or how it works; it can safely assume that the card understands the set of well-defined commands that are defined in the standard protocol.
USB
Open Host Controller Interface
The OHCI standard for USB is similar to the OHCI standard for FireWire, but supports USB 1.1 (full and low speeds) only; so as a result its register interface looks completely different. Compared with UHCI, it moves more intelligence into the controller, and thus is accordingly much more efficient; this was part of the motivation for defining it. If a computer provides non-x86 USB 1.1, or x86 USB 1.1 from a USB controller that is not part of an Intel or a VIA chipset, it probably uses OHCI (e.g. OHCI is common on add-in PCI Cards based on an NEC chipset). It has many fewer intellectual property restrictions than UHCI.[1] It only supports 32-bit memory addressing,[2] so it requires an IOMMU or a computationally expensive bounce buffer to work with a 64-bit operating system. OHCI interfaces to the rest of the computer only with memory-mapped I/O.[2]
Universal Host Controller Interface
Universal Host Controller Interface (UHCI) is a proprietary interface created by Intel for USB 1.x (full and low speeds). It requires a license from Intel. A USB controller using UHCI does little in hardware and requires a software UHCI driver to do much of the work of managing the USB bus.[1] It only supports 32-bit memory addressing,[3] so it requires an IOMMU or a computationally expensive bounce buffer to work with a 64-bit operating system. UHCI is configured with port-mapped I/O and memory-mapped I/O, and also requires memory-mapped I/O for status updates and for data buffers needed to hold data that needs to be sent or data that was received.[3]
Enhanced Host Controller Interface
Enhanced Host Controller Interface (EHCI) is a high-speed controller standard applicable to USB 2.0. The existence of UHCI and OHCI based systems, as existed previously, entailed greater complexity and costs than necessary. Consequently the USB-IF insisted on a public specification for EHCI. Intel hosted EHCI conformance testing and this helped to prevent incursion of proprietary features.
Originally a PC providing high-speed ports had two controllers, one handling low- and full-speed devices and the second handling high-speed devices. Typically such a system had EHCI and either OHCI or UHCI drivers. The UHCI driver provided low- and full-speed functions using an Intel or VIA chipset's USB host controllers on the motherboard. The OHCI driver provided low and full speed functions for USB ports of a PCI expansion card with any other chipset vendor's integrated USB host controllers or discrete controller chipsets attached to the computer's expansion bus, if present. The EHCI driver provided high-speed functions for USB ports on the motherboard or on the discrete USB controller. In more recent hardware, all ports are routed through an internal "rate-matching" hub (RMH) and the EHCI controller indirectly provides full and low speed USB functions.
EHCI was designed to work with 32-bit or 64-bit operating systems, so it does not need a bounce buffer or IOMMU to work with a 64-bit operating system as long as a rate-matching hub is implemented to provide full-speed and low-speed connectivity instead of companion controllers.
Extensible Host Controller Interface
Extensible Host Controller Interface (XHCI) is the newest host controller standard that improves speed, power efficiency and virtualization over its predecessors The goal was also to define a USB host controller to replace UHCI/OHCI/EHCI. It supports all USB device speeds (USB 3.1 SuperSpeed+, USB 3.0 SuperSpeed, USB 2.0 Low-, Full-, and High-speed, USB 1.1 Low- and Full-speed).
See also
- Universal Serial Bus (USB)
- Advanced Host Controller Interface (AHCI)
- EHCI (xHCI 0.9 SuperSpeed USB Architecture - USB 3.0)
- Extensible Host Controller Interface (XHCI)
- WHCI 1.0 (Wireless USB 1.0)
- RAID Controller
- Host adapter
- LPCIO
- EHCI
References
- ^ a b gowdy (August 27, 2007). "Linux USB FAQ". Retrieved April 13, 2014.
- ^ a b ftp://ftp.compaq.com/pub/supportinformation/papers/hcir1_0a.pdf
- ^ a b ftp://ftp.netbsd.org/pub/NetBSD/misc/blymn/uhci11d.pdf
External links
- An OHCI for USB standard document from Compaq, Microsoft and National Semiconductor (PDF)
- Linux kernel source: OHCI and EHCI documentation
- Intel EHCI Specification
- Intel xHCI Specification
- xHCI draft specification is finally available
- http://www.intel.com/content/www/us/en/io/universal-serial-bus/ehci-specification.html