Jump to content

Muzzle flash

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by 210.49.94.137 (talk) at 11:28, 4 October 2018 (→Muzzle flash characteristics). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

Photo of the Five-seven muzzle flash in dim lighting
FN Five-seven muzzle flash
Muzzle flash of an Israeli Merkava IIId Baz tank IMI 120 mm gun
USS Iowa (BB-61) fires a full broadside during a target exercise near Vieques Island, Puerto Rico, 1 July 1984, showing the muzzle blast from its 16 inch main battery and the blast's effect on the water surrounding the ship.

Muzzle flash is the visible light of a muzzle blast, which expels high-temperature, high-pressure gases from the muzzle of a firearm. The blast and flash are caused by the combustion products of the gunpowder, and any remaining unburned powder, mixing with the ambient air. The size and shape of the muzzle flash is dependent on the type of ammunition being used and the individual characteristics of firearm and any devices attached to the muzzle (such as a muzzle brake or flash suppressor).

Muzzle blast

The muzzle blast is the explosive expansion of propellant gases when the barrel seal previously maintained by the projectile is suddenly removed as the said projectile leaves the muzzle. The blast is often broken down into two components, an auditory component[1] and a non-auditory component.[2] The auditory component, the sound of the gunshot, is important because it can cause hearing loss or give away the gun's position, while the non-auditory component, the overpressure wave, can cause damage to nearby items.

Soldiers covering their ears while firing a 120-mm mortar

Sound

The sound of a gunshot, also known as the muzzle report, may have two sources: the muzzle blast itself, and any shockwave produced by a transonic or supersonic projectile. Suppressors help to reduce the muzzle report of firearms by providing a larger area for the propellant gas to expand, decelerate and cool before release.[3]

Overpressure wave

The overpressure wave from the muzzle blast of a firearm can contain a significant amount of energy because it travels at an extremely high velocity. Residual pressures at the muzzle can be a significant fraction of the peak chamber pressure, especially when slow burning powders or short barrels are used. This energy can also be harnessed by a muzzle brake to reduce the recoil of the firearm, or by a muzzle booster to provide energy to operate the action.[4]

Problems caused by muzzle blast

Muzzle blasts can easily exceed sound pressure levels of 140 decibels, which can cause permanent hearing loss even with brief and infrequent exposure.[5] With big guns such as artillery, that danger can extend outwards a significant distance from the muzzle.[6]

The force of the muzzle blast can cause damage to items near the muzzle, and with artillery, the energy is sufficiently large to cause severe damage to surrounding structures and vehicles.[7] It furthermore can violently raise dust and debris when firing rifles from prone position and so give away the position. Preventive actions may consist in wetting dry ground or covering the area around the muzzle with a tarpaulin.

Muzzle flash

Muzzle flash of a revolver. Note the minor flash at the gap between cylinder and barrel.

The muzzle flash refers to the light emitted by the muzzle blast, both visible light and infrared. Both heat and pressure can result in light being emitted.

Muzzle flash characteristics

Muzzle flash can be broken down into five distinct components.[8]

  • Muzzle glow is a reddish glow that is visible before the bullet leaves the barrel. Muzzle glow is created by superheated gases that have leaked past the projectile and have exited the barrel.
  • The primary flash is caused by propellant gases exiting the firearm behind the bullet. Although amongst the brightest of the flashes, the heat of the primary flash dissipates quickly and thus is no longer visible.
  • The intermediate flash is caused by shock waves created by the high speeds of the escaping gases and projectile, and appears as a reddish disc shape in front of the muzzle.
  • The secondary flash appears farthest from the muzzle as a large white or yellow flame. Secondary flash is caused by the reaction of incompletely combusted ejecta mixing with abundant oxygen in the atmosphere surrounding the muzzle.[9]
  • Following the dissipation of the muzzle flash, partially unburnt powder or other heated materials can be ejected from the muzzle and appear as residual sparks.

Suppression

Muzzle flash, particularly the long duration secondary flash, is an inherent problem in most firearms. Due to its brightness, muzzle flash can temporarily blind the shooter, or give away the shooter's location, especially at night. Ingestion of the muzzle flash from aircraft mounted guns has also been implicated in compressor stall and flameout, causing loss of aircraft.[10]

Flash suppressors attempt to suppress the flash mechanically, by interfering with the shock wave using either a cone or a series of slots at the muzzle of the firearm. However, since the primary cause of the secondary flash is combustion of hydrogen and carbon monoxide, chemical approaches are also used. In World War I, bags of sodium chloride (table salt) were placed in front of the propellant charges of artillery to suppress the flash. Addition of a few percent of alkali salts to the powder for flash suppression is common, typically salts of potassium such as potassium chloride, potassium sulfate, potassium carbonate, and potassium bicarbonate. In both cases, the salts act as catalysts, and interfere with the hydrogen-oxygen combustion to reduce the muzzle flash. The side effects of the alkali salts is a reduction in power, an increase in smoke, and fouling and corrosion of the firearm and nearby equipment (a significant concern with aircraft guns). Ammonium chloride and ammonium nitrate salts have also been tried with success.[10][11]

Detection, with muzzle blast

Gunfire locators detect muzzle blast with microphones and triangulate the location where the shots were fired. They are commercially available, and have been installed in many high-crime areas of large cities. They provide a fairly precise location of the source of a shot fired outdoors—99% to within 33 feet (10 m) or better—and can provide it to police within seconds of a firing.[12]

Muzzle flashes create distinct signatures that can be located using infrared imaging technology.[13] Technology is being developed to detect enemy muzzle flashes before the projectile reaches its target.

See also

Wikimedia Commons has media related to Muzzle flash.

References

  1. ^ Muzzle Blast Sound Intensity, Firearm Sound Pressure Level
  2. ^ Blast Overpressure Studies. Nonauditory Damage Risk Assessment for Simulated Muzzle Blast from a l2Omm Ml2l Mortar System. (abstract)
  3. ^ "Definition for "sound suppressor"". MidwayUSA.
  4. ^ "Definition for "compensator"". MidwayUSA.
  5. ^ Hearing protection FAQ Archived 2007-06-28 at the Wayback Machine
  6. ^ Prediction of Standoff Distances to Prevent Loss of Hearing from Muzzle Blast
  7. ^ Muzzle Blast Damage to Combat Vehicles (abstract)
  8. ^ Tony DiGiulian, Muzzle flash, 14 August 2006
  9. ^ G. Klingenberg, Gun Muzzle Blast and Flash, 21 July 1988
  10. ^ a b WO application 1986/001796A1, Winkler, David Allen, "Gun Flash Suppressants", published 1986-09-24 
  11. ^ Explosives, 6th Ed. Josef Köhler (trans.). Wiley-VCH. 2007. p. 218. ISBN 978-3-527-31656-4. {{cite book}}: Unknown parameter |authors= ignored (help)CS1 maint: others (link)
  12. ^ "Random Gunfire Problems and Gunshot Detection Systems" (PDF). U.S. Department of Justice. December, 199. {{cite web}}: Check date values in: |date= (help)
  13. ^ Infrared sniper detection enhancement
Retrieved from "https://en.wikipedia.org/w/index.php?title=Muzzle_flash&oldid=862440302"