Prince Rupert's cube

A unit cube with a hole cut through it, large enough to allow Prince Rupert's cube to pass

In geometry, Prince Rupert's cube (named after Prince Rupert of the Rhine) is the largest cube that can pass through a hole cut through a unit cube, i.e. through a cube whose sides have length 1, without splitting the cube into two pieces. Its side length is approximately 6% larger than that of the unit cube through which it passes. The problem of finding the largest square that lies entirely within a unit cube is closely related, and has the same solution.

Solution

If two points are placed on two adjacent edges of a unit cube, each at a distance of 3/4 from the point where the two edges meet, then the distance between the two points will be

${\frac {3{\sqrt {2}}}{4}}\approx 1.0606601.$

These two points, together with a second set of two points placed symmetrically on the opposite face of the cube, form the four vertices of a square that lies entirely within the unit cube. This square, extruded in both directions perpendicularly to itself, forms the hole through which a cube larger than the original one (up to side length ${\tfrac {3{\sqrt {2}}}{4}}$) may pass.

The parts of the unit cube that remain, after emptying this hole, form two triangular prisms and two irregular tetrahedra, connected by thin bridges at the four vertices of the square. Each prism has as its six vertices two adjacent vertices of the cube, and four points along the edges of the cube at distance 1/4 from these cube vertices. Each tetrahedron has as its four vertices one vertex of the cube, two points at distance 3/4 from it on two of the adjacent edges, and one point at distance 3/16 from the cube vertex along the third adjacent edge.

History

Prince Rupert's cube is named after Prince Rupert of the Rhine. According to a story recounted in 1693 by English mathematician John Wallis, Prince Rupert wagered that a hole could be cut through a cube, large enough to let another cube of the same size pass through it. Wallis showed that in fact such a hole was possible (with some errors that were not corrected until much later), and Prince Rupert won his wager.

Wallis assumed that the hole would be parallel to a space diagonal of the cube. The projection of the cube onto a plane perpendicular to this diagonal is a regular hexagon, and the best hole parallel to the diagonal can be found by drawing the largest possible square that can be inscribed into this hexagon. Calculating the size of this square shows that a cube with side length

${\sqrt {6}}-{\sqrt {2}}\approx 1.03527$,

slightly larger than one, is capable of passing through the hole.

Approximately 100 years later, Dutch mathematician Pieter Nieuwland found that a better solution (in fact, the optimal solution) may be achieved by using a hole with a different angle than the space diagonal. Nieuwland died in 1794 (a year after taking a position as a professor at the University of Leiden) but his solution was published posthumously in 1816 by Nieuwland's mentor, Jean Henri van Swinden.

Since then, the problem has been repeated in many books on recreational mathematics, in some cases with Wallis' suboptimal solution instead of the optimal solution.

Models

The construction of a physical model of Prince Rupert's cube is made difficult by the accuracy with which such a model would need to be measured, and the thinness of the connections between the remaining parts of the unit cube after the hole is cut through it; for this reason, the problem has been called "mathematically possible but practically impossible". Nevertheless, in a 1950 survey of the problem, D. J. E. Schrek published photographs of a model of a cube passing through a hole in another cube. Martin Raynsford has designed a template for constructing paper models of a cube with another cube passing through it; however, in order to account for the tolerances of paper construction and not tear the paper at the narrow joints between parts of the punctured cube, the hole in Raynsford's model only lets cubes through that are slightly smaller than the outer cube.

Generalizations

The cube is not the only body that can pass through a hole cut into a copy of itself; the same is true for the regular tetrahedron and octahedron.

Another way to express the same problem is to ask for the largest square that lies within a unit cube. More generally, Jerrard & Wetzel (2004) show how to find the largest rectangle of a given aspect ratio that lies within a unit cube. As they show, the optimal rectangle must always pass through the center of the cube, with its vertices on edges of the cube. Based on this, they show, depending on the desired aspect ratio, that the optimal rectangle must either lie on a plane that cuts diagonally through four corners of the cube, or it must be formed by an isosceles right triangle on one corner of the cube and by the two opposite points, as in the case of Prince Rupert's problem. If the aspect ratio is not constrained, the rectangle with the largest area that fits within a cube is the one that has two opposite edges of the cube as two of its sides, and two face diagonals as the other two sides.

Alternatively, one may ask for the largest $m$-dimensional hypercube that may be drawn within an $n$-dimensional unit hypercube. The answer is always an algebraic number. For instance, the problem for $(m,n)=(3,4)$ asks for the largest cube within a four-dimensional hypercube. After Martin Gardner posed this question in Scientific American, Kay R. Pechenick DeVicci and several other readers showed that the answer for the (3,4) case is the square root of the smaller of two real roots of the polynomial $4x^{4}-28x^{3}-7x^{2}+16x+16$, which works out to approximately 1.007435. For $m=2$, the optimal side length of the largest square in an $n$-dimensional hypercube is either ${\sqrt {n/2}}$ or ${\sqrt {n/2-3/8}}$, depending on whether $n$ is even or odd respectively.

External links

• Weisstein, Eric W. "Prince Rupert's Cube". MathWorld.