Rover 20

Rover 20
Tourer first registered December 1907
Overview
Manufacturer	Rover
Production	1907–1910
Model years	1908–1910
Body and chassis
Body style	open tourer landaulet chassis only
Layout	FR
Powertrain
Engine	3,251 cc (198.4 cu in) Straight-4
Dimensions
Wheelbase	114 in (2,896 mm) tourer 120 in (3,048 mm) landaulet Track 53 in (1,346 mm) wood Track 55 in (1,397 mm) wire
Length	156 in (3,962 mm)
Width	63 in (1,600 mm)
Kerb weight	Chassis 17 cwt, 1,904 lb (864 kg)

Rover 20hp
engine's near side
Overview
Manufacturer	Rover
Layout
Configuration	straight 4-cylinder
Displacement	3,251 cc (198.4 cu in)
Cylinder bore	97 mm (3.8 in)
Piston stroke	110 mm (4.3 in)
Cylinder block material	cast iron, en bloc, four separately cast cylinders
Cylinder head material	in unit with blocks
Valvetrain	side valves
Combustion
Fuel system	Rover (pat.) carburettor gravity fed from fuel tank in scuttle
Management	Bosch H T magneto or accumulator
Fuel type	petrol
Oil system	splash
Cooling system	water: flattened tube radiator, water pump, fan
Output
Power output	2 bhp (1.5 kW; 2.0 PS) @2,400 rpm Tax horsepower 23.33
Chronology
Predecessor	Rover 16 but 20 has been bored out by 2mm

The Rover 20 was a new medium sized car announced by Rover in June 1907. It was a production version of the car which won the Isle of Man Tourist Trophy Race in 1906. However artillery wood wheels were fitted instead of the (still recommended) wire wheels used in the race and the longer wheelbase allowed the engine to be kept out of the passenger area. The prototype's engine came back beneath the petrol tank.

With a few breaks Rover kept a premium 20 tax horsepower car in their catalogue until the outbreak of war in 1939. In the early 1950s an equivalent model returned to the market, the 2.6-litre Rover 90 and later Rover's 3-litre.

1907 model

Engine

The engine was very much based on the Rover 16's but the bore had been increased 2mm. There were a number of minor improvements. The water inlet pipe was now to the other side of the engine to provide better access to the valves and tappets. The oil box (reservoir) was now at the left rear of the engine so a catcher for oil thrown up by the flywheel is no longer necessary. Lubrication pipes had been mounted lower. There was a new partition between sump and clutch housing so oil was not thrown to the clutch. Rover's engine braking system was fitted, it has the ability to close the engine's valves.

engine's off side showing ignition etc The petrol tank was above the driver's knees with its filler in front of the centre of the windscreen and the tank shaped to form the car's dashboard and scuttle. It was high enough to always provide sufficient head of petrol and no pressure feed was needed. The coil is mounted on a board which slides in grooves on the front of the petrol tank. The coil is used with either an accumulator or the Eisemann ignition magneto and provides both ignition systems. At the forward right hand end of the engine a shaft spur-driven from the crankshaft powers the water circulation pump, the magneto and the contact maker. The magneto and contact maker are linked so one lever controls the advance or retard of the ignition timing. Crankcase, clutch case and gearbox case are all aluminium castings. They are assembled to form one unit.

Gearbox

vertical section of clutch and gearbox The four-speed gearbox had a gate change. The lever was located by the driver's right hand. Direct drive was on third gear, fourth gear was indirect. For a reduced price a three-speed gearbox could be supplied along with smaller diameter tyres in which case no magneto ignition system is fitted. The clutch has a cone stop to ease gear changes by slowing the clutch and the gearshift motion. Ball bearings are fitted throughout to the engine and gear box and to the road wheels.

Brakes suspension steering

Rover's system of front suspension

The chassis was suspended from the front axle at just one point by a pivoted transverse leaf spring which made no contribution to transverse stability and the whole car rested on just three points. Radius rods from the gearbox take up braking strains and act as distance stays for the back axle. The front end of these stays have buffer springs The foot brake is the contracting band type, the hand brake is of the pull-on internal expanding type. Both sets of brake are metal to metal. The action of the engine brake avoids much use of the conventional braking system. The rear springs attach by means of a spherical case clipping over a spherical turned part of the axle casing thus allowing a little motion due to bumps.

The chassis is built up from steel flitch plates over ash to give the necessary strength with flexibility.

Engine controls

A pair of Autoloc levers move over the top of the steering wheel. They operate the throttle and ignition. A pedal controls the engine braking system. Road tests as late as 1911 noted how Rover cars lacked accelerator pedals.

Winning the RAC Tourist Trophy 1907

1930 Light Twenty

This car was fitted with a Rover Meteor 20 hp engine but otherwise was identical with the Rover Two-litre Sportsman's coupé

Rover Speed Twenty
Overview
Manufacturer	Rover
Production	1933–1935 xxxxxxxxxxxx
Model years	1934–1935
Body and chassis
Body style	xxxxxxxxxxxx
Layout	FRxxxxxxxxxxxx
Powertrain
Engine	2565 cc Straight-6xxxxxxxxxxxx
Dimensions
Wheelbase	111 in (2,800 mm) ’’’Track’’’ 51 in (1,300 mm)xxxxxxxxxxxx
Length	172.5 in (4,380 mm)xxxxxxxxxxxx
Width	61 in (1,500 mm)xxxxxxxxxxxx
Kerb weight	Saloon 19½ cwt, 2,184 lb (991 kg)xxxxxxxxxxxx

Rover 20
Overview
Manufacturer	Rover
Layout
Configuration	Straight 6-cylinderxxxxxxxxxxxx
Displacement	2,565 cc (157 cu in)xxxxxxxxxxxx
Cylinder bore	72 mm (2.8 in)xxxxxxxxxxxx
Piston stroke	105 mm (4.1 in)xxxxxxxxxxxx
Output
Power output	72 bhp (54 kW; 73 PS) @x rpm Tax horsepower 19.28xxxxxxxxxxxx

1939 Twenty

Rover 20 P2
Overview
Manufacturer	Rover
Body and chassis
Body style	sports saloon drophead coupé
Layout	FR

Rover 20
Layout
Configuration	Straight 6-cylinderxxxxxxxxxxxx
Displacement	2,512 cc (153 cu in)xxxxxxxxxxxx
Cylinder bore	73 mm (2.9 in)xxxxxxxxxxxx
Piston stroke	100 mm (3.9 in)xxxxxxxxxxxx
Output
Power output	not published Tax horsepower 19.82xxxxxxxxxxxx

External links

• Tickford coupé 1940