Time base correction
This article includes a list of references, related reading or external links, but its sources remain unclear because it lacks inline citations. (March 2010) (Learn how and when to remove this template message)
Time base correction is a technique to reduce or eliminate errors caused by mechanical instability present in analog recordings on mechanical media. Without time base correction, a signal from a videotape recorder (VTR) or videocassette recorder (VCR) cannot be mixed with other, more time stable devices found in television studios and post-production facilities. Most broadcast quality VCRs have simple time base correctors built in though external time base correctors (TBCs) are often used. Some high end domestic analogue video recorders and camcorders also include a TBC circuit, which typically can be switched off if required.
Time base correction counteracts errors by buffering the video signal as it comes off the videotape at an unsteady rate, and releasing it at a steady rate. TBCs also allow a variable delay in the video stream. By adjusting the rate and delay using a waveform monitor and a vectorscope, the corrected signal can now match the timing of the other devices in the system. If all of the devices in a system are adjusted so their signals meet the video switcher at the same time and at the same rate, the signals can be mixed. A single master clock or "sync generator" provides the reference for all of the devices' clocks.
As far back as 1956, professional reel-to-reel audio tape recorders relying on mechanical stability alone were stable enough that pitch distortion could be below audible level without time base correction. However, the higher sensitivity of video recordings meant that even the best mechanical solutions still resulted in detectable distortion of the video signals. A video signal consists of picture information but also sync and subcarrier signals which allow the image to be framed up square on the monitor, reproduce colors accurately[note 1] and, importantly, allow the combination and switching of two or more video signals.
Implicit in the idea of time base correction is that there must be some target time base that the corrector is aiming for. There are two time bases commonly used. The first method is to make the frames, fields and lines come out smoothly and uniformly, at the rates specified by the standards using an oscillator for time reference. The alternative to this method is to align the frames, fields, and lines with some external signal, a procedure called genlocking.[note 2] Genlocking allows sources that are not themselves genlock-capable to be used with production switchers and A/B roll editing equipment. Stand-alone broadcast model time base correctors typically will genlock the signal to an external sync reference, and also allow the brightness, contrast, chrominance, and color phase ("tint" or "hue") to be adjusted.
Some TBCs featured a Drop Out Compensation (DOC) circuit that enabled videotape flaws caused by oxide drop-out to be temporarily corrected. The DOC circuit required dedicated cabling between the videotape player and the TBC in which irregularities were detected in portions of the video image. Previously captured and stored lines of video would then be superimposed over the flawed video lines.
A variant of the time base corrector is the frame synchronizer which allows devices that cannot be "steered" by an advanced sync signal to also be time base corrected and/or timed into a system. Satellites, microwave transmitters and other broadcast signals as well as consumer VTRs cannot be sent an advance sync signal. A frame synchronizer stores at least a full frame of video. If the buffer over or under fills, the Frame Sync will hold the last good frame of video until another full frame's worth of video is received. Usually this is undetectable to viewers.
- In particular, the color information in NTSC is encoded relative to the phase of a high frequency color sub-carrier, making the displayed colors extremely sensitive to time base errors.
- To handle a randomly varying analog signal, a stable "pilot tone" is recorded along with the signal. Upon playback the pilot tone is extracted with filters and frequency variations in the pilot tone are used to generate an error signal that drives the time base correction circuits. A notch filter is then used to suppress the pilot tone from the recovered signal.
- Extensive guide to TBCs and their selection
- A digital synchronizer for a video-tape recorder, Bucciarelli, F.V.; Proceedings of the IEEE, Volume 61, Issue 4, April 1973 Page(s):506 - 507
- oldvcr.com Sony, Sony BVT-800, Professional Timebase Corrector
- oldvcr.com FOR.A FA-410, Professional Timebase Corrector